AVM FRITZ!Box 3390

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

Write a short, relevant description of the device. Include a technical overview, but avoid marketing buzzwords/useless stuff. Two to four sentences is about right. A picture is good, too. Edit the page to see how to add pictures.

FRITZ!Box 3390

Currently not official supported yet. But there are two options available:

1. it works with 3370 Firmware (but without Wifi function and only power led support, use the micron version). Follow the instructions at fritz.box.wlan.3370.

2. installation instruction for an unofficial Port for Fritzbox 3390 is here: https://www.aboehler.at/doku/doku.php/projects:fritz3390. Also PR Request is pending at https://github.com/openwrt/openwrt/pull/2662 and https://github.com/openwrt/openwrt/pull/3656

CPU Ram Flash Network WLAN USB Serial JTag
Lantiq XWAY VRX288 128 MiB 128 MiB 4x 1Gbit abgn 2x 2.0 4pin Solderpads, 2.54mm, 3.3V, 115200 Baud ?
Architecture MIPS32
Vendor Lantiq
Bootloader EVA(AVM) Revision: 1.1660 Version: 2660
System-On-Chip VR9: VRX288, Atheros AR9342 SoC
CPU Cores 2
CPU MIPS 34Kc V1.2 2×500 Mhz
xDSL
VoIP via FRITZ!App Fon
Flash-Chip MICRON MT29F1G08ABADAWP, 2048 Pagesize 128k Blocksize 1024 Blocks 8Bit 1 CS HW
Flash size 128 MiB
RAM 128 MiB
Wireless AR9580 and AR9381
Switch Soc-integrated
DSL Lantiq VRX288 + VRX206
USB Yes 2 x 2.0
Serial Yes
JTAG Yes

Front of the casing

Back of the casing

PCB Topside

PCB Bottom

Remove rubber feet and unscrew 4 screws Torx T9. Open case.

port.serial general information about the serial port, serial port cable, etc.
https://www.zebradem.com/wiki/index.php?title=Serielle_Konsole for information specific to Fritz!Boxes

How to connect to the Serial Port of this specific device:

Seen from the rear of the device, the most left of the 4 holes is square cut while the others are round.

Pin 1 [ ] 2 3 4
Function VCC RX TX GND

Connection-Example of FT232

similar examples from Fritzbox 3370: Serial connectors holes, rear side.

Serial connection with a MAX3232/RS232 TTL to Serial Port Converter.

Serial connection parameters
for FRITZ!Box 3390
115200, 8N1

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

1606134986,ROM VER: 1.1.4 1606134986,CFG 05 1606134986,ç$ DC! ¤¥„„DC[-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\] 1606134988,(AVM) EVA Revision: 1.1660 Version: 2660 1606134988,(C) Copyright 2005 AVM Date: Apr 24 2013 Time: 12:33:43 (0) 3 0x0-0x740D 1606134988,[FLASH:] MACRONIX Uniform-Flash 256kB 256 Bytes WriteBuffer 1606134988,[FLASH:](Eraseregion [0] 4 sectors a 64kB) 1606134988,[NAND:] 128MB MICRON 2048 Pagesize 128k Blocksize 1024 Blocks 8Bit 1 CS HW 1606134988,[SYSTEM:] VR9 on 500MHz/250MHz/250MHz 1606134988,.Atheros 8030/35 detected 1606134988,Eva_AVM >................................................. 1606135000,Lantiq xDSL CPE VR9 1606135000,phym = 08000000, mem = 08000000, max_pfn = 00008000 1606135000,Reserving memory for CP1 @0xa8000000, size 0x00000000 1606135000,plat_device_tree_setup: AVM hardware subrevision 1 1606135000,plat_device_tree_setup: using Fallback device-tree of AVM hardware subrevision 0 1606135000,DT: d0 0d fe ed 00 00 0d f1 1606135000,[ 0.000000] Linux version 3.10.73 (jpluschke@EmbeddedVM) (gcc version 4.8.3 (Buildroot 2014.08) ) #1 SMP Wed Aug 21 17:10:32 CEST 2019 1606135000,[ 0.000000] [unv_init] 0x81017ad0[0] 1606135000,[ 0.000000] [env_init] 0x81017b10[1] 1606135000,[ 0.000000] [env_init] 0x81017c10[2] 1606135000,[ 0.000000] [env_init] switch to ram location 1606135000,[ 0.000000] [init_avm_kernel_config] AVM Kernel Config (ptr 80825000) 1606135000,[ 0.000000] [init_avm_kernel_config] AVM Kernel Config: module memory entry 1606135000,[ 0.000000] [init_avm_kernel_config] AVM Kernel Config: version info entry 1606135000,[ 0.000000] [init_avm_kernel_config] AVM Kernel Config: device-tree for subrev 0 found 1606135000,[ 0.000000] bootconsole [early0] enabled 1606135000,[ 0.000000] CPU0 revision is: 00019556 (MIPS 34Kc) 1606135000,[ 0.000000] Determined physical RAM map: 1606135000,[ 0.000000] memory: 08000000 @ 00000000 (usable) 1606135000,[ 0.000000] Initrd not found or empty - disabling initrd 1606135000,[ 0.000000] [module-alloc] use 0xcf4000 bytes at 0x81104000 1606135000,[ 0.000000] PERCPU: Embedded 7 pages/cpu @81dfc000 s7072 r8192 d13408 u32768 1606135000,[ 0.000000] Kernel command line: annex=B console=ttyS0,115200n8r nor_size=0MB sflash_size=256KB nand_size=128MB ethaddr=9C:C7:A6:7E:C8:3A 1606135000,[ 0.000000] [NAND] nand_size = 0x8000000 1606135000,[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) 1606135000,[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) 1606135000,[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) 1606135000,[ 0.000000] Writing ErrCtl register=00042200 1606135000,[ 0.000000] Readback ErrCtl register=00042200 1606135000,[ 0.000000] Memory: 107352k/131072k available (5707k kernel code, 23720k reserved, 2688k data, 300k init, 0k highmem) 1606135000,[ 0.000000] Hierarchical RCU implementation. 1606135000,[ 0.000000] NR_IRQS:181 1606135000,[ 0.000000] SRSConf0 0x3feffbfe: SRS1: 0xffffffff, SRS2 0xffffffff, SRS3 0xffffffff 1606135000,[ 0.000000] Lantiq ICU driver, version 3.0.1, (c) 2001-2011 Lantiq Deutschland GmbH 1606135000,[ 0.000000] Console: colour dummy device 80x25 1606135000,[ 0.000000] console [ttyS0] enabled, bootconsole disabled 1606135000,[ 0.000000] console [ttyS0] enabled, bootconsole disabled 1606135000,[ 0.020000] Calibrating delay loop... 331.77 BogoMIPS (lpj=1658880) 1606135000,[ 0.080000] pid_max: default: 32768 minimum: 301 1606135000,[ 0.080000] Security Framework initialized 1606135000,[ 0.080000] Mount-cache hash table entries: 512 1606135000,[ 0.090000] CPU1 revision is: 00019556 (MIPS 34Kc) 1606135000,[ 0.170000] Brought up 2 CPUs 1606135000,[ 0.170000] [yield_context_init] cpu=1 tc=2 mask=300 1606135000,[ 0.180000] [yield_context_init] cpu=0 tc=3 mask=410 1606135000,[ 0.180000] devtmpfs: initialized 1606135000,[ 0.200000] pinctrl core: initialized pinctrl subsystem 1606135000,[ 0.200000] Creating Config Table 1606135000,[ 0.200000] [avm_generate_hw_config_table_from_device_tree] gpio_cnt: 33 1606135000,[ 0.210000] NET: Registered protocol family 16 1606135000,[ 0.220000] Reboot Status is: Power-On 1606135000,[ 0.220000] [TFFS3_Early_Init] called 1606135000,[ 0.230000] [avmnet] [avmnet_cfg_init] Driver version: 6.221.2.4 - Revision 1496:3477 - Mi 21. Aug 17:09:45 CEST 2019 1606135001,[ 0.850000] Lantiq PCIe Root Complex driver, version 2.0.0, (c) 2001-2011 Lantiq Deutschland GmbH 1606135001,[ 0.900000] bio: create slab <bio-0> at 0 1606135001,[ 0.900000] PCI host bridge to bus 0000:00 1606135001,[ 0.910000] pci_bus 0000:00: root bus resource [mem 0x1c000000-0x1cffffff] 1606135001,[ 0.910000] pci_bus 0000:00: root bus resource [io 0x1d800000-0x1d8fffff] 1606135001,[ 0.920000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] 1606135001,[ 0.930000] ifx_pcie_rc_class_early_fixup port 0: fixed pcie host bridge to pci-pci bridge 1606135001,[ 0.940000] pci 0000:00:00.0: BAR 8: assigned [mem 0x1c000000-0x1c0fffff] 1606135001,[ 0.940000] pci 0000:00:00.0: BAR 9: assigned [mem 0x1c100000-0x1c1fffff pref] 1606135001,[ 0.950000] pci 0000:01:00.0: BAR 0: assigned [mem 0x1c000000-0x1c01ffff 64bit] 1606135001,[ 0.950000] pci 0000:01:00.0: BAR 6: assigned [mem 0x1c100000-0x1c10ffff pref] 1606135001,[ 0.960000] pci 0000:00:00.0: PCI bridge to [bus 01] 1606135001,[ 0.960000] pci 0000:00:00.0: bridge window [mem 0x1c000000-0x1c0fffff] 1606135001,[ 0.970000] pci 0000:00:00.0: bridge window [mem 0x1c100000-0x1c1fffff pref] 1606135001,[ 0.970000] NET: Registered protocol family 8 1606135001,[ 0.980000] NET: Registered protocol family 20 1606135001,[ 0.980000] Switching to clocksource MIPS 1606135001,[ 1.030000] NET: Registered protocol family 2 1606135001,[ 1.030000] TCP established hash table entries: 1024 (order: 1, 8192 bytes) 1606135001,[ 1.040000] TCP bind hash table entries: 1024 (order: 1, 8192 bytes) 1606135001,[ 1.040000] TCP: Hash tables configured (established 1024 bind 1024) 1606135001,[ 1.050000] TCP: reno registered 1606135001,[ 1.050000] UDP hash table entries: 256 (order: 1, 8192 bytes) 1606135001,[ 1.060000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) 1606135001,[ 1.070000] NET: Registered protocol family 1 1606135001,[ 1.070000] Lantiq CGU driver, version 1.1.32, (c) 2001-2011 Lantiq Deutschland GmbH 1606135001,[ 1.080000] IFX DMA driver, version ifxmips_dma_core.c:v1.0.17, (c) 2009 Infineon Technologies AG 1606135001,[ 1.080000] skb_shared_size:184 1606135001,[ 1.090000] squashfs: version 4.0 (2009/01/31) Phillip Lougher 1606135001,[ 1.100000] fuse init (API version 7.22) 1606135001,[ 1.104000] msgmni has been set to 209 1606135001,[ 1.110000] io scheduler noop registered (default) 1606135001,[ 1.450000] ttyS0 at MMIO 0x1e300c00 (irq = 107) is a PORT_IFX_ASC 1606135001,[ 1.450000] ifx_usif_uart_init: uart_register_driver failed 1606135001,[ 1.460000] avm_net_trace: Up and running. 1606135001,[ 1.460000] [loadcontrol] set auto - scale=1 1606135001,[ 1.470000] Lantiq Thermal Sensor driver, version 1.0.3, (c) 2001-2011 Lantiq Deutschland GmbH 1606135001,[ 1.480000] ifx_pmu_init: Major 244 1606135001,[ 1.480000] Lantiq PMU driver, version 1.2.6, (c) 2001-2011 Lantiq Deutschland GmbX 1606135001,[ 1.490000] Lantiq GPIO driver, version 1.3.2, (c) 2001-2011 Lantiq Deutschland GmbH 1606135001,[ 1.500000] Infineon Technologies RCU driver version 1.0.7 1606135001,[ 1.520000] loop: module loaded 1606135001,[ 1.520000] nbd: registered device at major!43 1606135001,[ 1.550000] [HSNAND] Hardware-ECC activated 1606135001,[ 01.550000] ONFI param page 0 valid 1606135001,[ 1.560000] ONFI flash detected 1606135001,[ 1.560000] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xf1 (Micron MT29F1G08ABADAWP), 128MiB, page size: 2048, OOB size: 64 1606135001,[ 1.570000] Scanning device for bad blocks 1606135001,[ 1.590000] [ifx_hsnand_command] read block is critical (column: 0x800 page: 0x2c80) 1606135002,[ 1.670000] Creating 6 MTD partitions on "ifx_hsnand": 1606135002,[ 1.670000] 0x000000000000-0x000000400000 : "kernel" 1606135002,[ 1.680000] 0x000000400000-0x000003400000 : "filesystem" 1606135002,[ 1.690000] 0x000003400000-0x000003800000 : "reserved-kernel" 1606135002,[ 1.690000] 0x000003800000-0x000006800000 : "reserved-filesystem" 1606135002,[ 1.700000] 0x000006800000-0x000006a00000 : "config" 1606135002,[ 1.710000] 0x000006a00000-0x000008000000 : "nand-filesystem" 1606135002,[ 1.720000] [TFFS3_Register_Panic_CB] registering panic callback for mtd ifx_hsnand 1606135002,[ 1.720000] [TFFS3_Register_Panic_CB] registering panic callback for mtd ifx_sflash 1606135002,[ 1.730000] Creating 3 MTD partitions on "ifx_sflash": 1606135002,[ 1.740000] 0x000000000000-0x000000020000 : "urlader" 1606135002,[ 1.740000] 0x000000020000-0x000000030000 : "tffs (1)" 1606135002,[ 1.750000] 0x000000030000-0x000000040000 : "tffs (2)" 1606135002,[ 1.760000] Lantiq SPI flash driver, version 2.0.1, (c) 2001-2011 Lantiq Deutschland GmbH 1606135002,[ 1.760000] tun: Universal TUN/TAP device driver, 1.6 1606135002,[ 1.770000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> 1606135002,[ 1.780000] SWAPI: Registered character device [switch_api] with major no [81] 1606135002,[ 1.780000] i2c /dev entries driver 1606135002,[ 1.790000] cpuidle: using governor ladder 1606135002,[ 1.790000] cpuidle: using governor menu 1606135002,Š[ 1.790000] AVM PA 4.3.14 2015-10-21 1606135002,[ 1.800000] AVM PA skb pktinfo at offset 136 size 196 1606135002,[ 1.800000] [loadcontrol]module avm_pa registered 1606135002,[ 1.810000] ipip: IPv4 over IPv4 tunneling driver 1606135002,[ 1.810000] TCP: cubic registered 1606135002,[ 1.820000] NET: Registered protocol family 10 1606135002,[ 1.820000] sit: IPv6 over IPv4 tunneling driver 1606135002,[ 1.830000] NET: Registered protocol family 17 1606135002,[ 1.830000] l2tp_core: L2TP core driver, V2.0 1606135002,[ 1.830000] l2tp_ip: L2TP IP encapsulation support (L2TPv3) 1606135002,[ 1.840000] l2tp_netlink: L2TP netlink interface 1606135002,[ 1.840000] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3) 1606135002,[ 1.850000] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3) 1606135002,[ 1.860000] 8021q: 802.1Q VLAN Support v1.8 1606135002,[ 1.860000] Key type dns_resolver registered 1606135002,[ 1.870000] <ifx_fix_timing> 1606135002,[ 1.870000] [TFFS3_Init] No!storage module registered, trying legacy fallback 1606135002,[ 1.880000] [TFFS3_Register_LGCY] Called 1606135002,[ 1.880000] [TFFS3_LGCY_Configure] Called 1606135002,[ 1.890000] [TFFS3_LGCY_Setup] using mtd7(tffs (1)), mtd8(tffs (2)) 1606135002,[ 1.890000] [TFFS3_LGCY_Setup] mtd "tffs (1)": segment value 1 1606135002,[ 1.900000] [TFFS3_LGCY_Setup] mtd "tffs (2)": segment value 1 1606135002,[ 1.900000] [TFFS3_LGCY_Setup] Using segment 1 (avail: 1 + 1) 1606135002,[ 1.910000] [TFFS3_LGCY_Setup] mtd8 size=0x10000 1606135002,[ 1.910000] TFFS: tiny flash file system driver. GPL (c) AVM Berlin (Version 3.0) 1606135002,[ 1.910000] [rescan_segment] Called with mode=2 1606135002,[ 1.910000] TFFS: Clearing index for update 1606135002,[ 1.930000] Adam2 environment variables API installed. 1606135002,[ 1.940000] [simple-profiling]: 2 performance counters implemented, NEW_34K 1606135002,[ 1.940000] Enable Performance Counter 0 for Data cache load/stores (User-Mode enabled Supervisor-Mode enabled Kernel-Mode enabled Exeption-Mode disable) 1606135002,[ 1.960000] Setup tcs=0x2 current_tc_mask=0x2, reg=0 1606135002,[ 1.960000] [simple-profiling]: 2 performance counters implemented, NEW_34K 1606135002,[ 1.970000] Enable Performance Counter 1 for Data cache load/store mi{ses (User-Mode enabled Supervisor-Mode enabled Kernel-Mode enabled Exeption-Mode disable) 1606135002,[ 1.980000] Setup tcs=0x2 current_tc_mask=0x2, reg=1 1606135002,[ 1.990000] {avmnet_cfg_netinit} 1606135002,[ 1.990000] [avmnet] No config found for HWRev 193, HWSubRev 1, Profile-ID 0, trying base config for HWSubRev 1606135002,[ 2.000000] [avmnet] No config found for HWRev 193, HWSubRev 1, trying base config for HWRev 1606135002,[ 2.010000] [avmnet] [avmnet_swi_7port_init] Init on module swi_vr9 called. 1606135002,[ 2.330000] [ppe_eth_init] init_hw() 1606135002,[ 2.340000] [init_hw] ppe_hw_init=0xff successful 1606135002,[ 2.340000] [ppe_eth_init] ifx_proc_file_create() 1606135002,[ 2.340000] [ppe_eth_init] dma_setup_init() 1606135002,[ 2.350000] [avmnet] [avmnet_swi_7port_disable_learning] Configuring CPU-port to receive all unknown unicast frames 0x48 1606135002,[ 2.360000] [avmnet] [avmnet_swi_7port_disable_learning] Configuring CPU-port to receive all unknown multicast frames 0x48 1606135006,[ 5.780000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth0): 9c:c7:a6:7e:c8:3a 1606135006,[ 5.790000] avmnet: avm_pa: register pid eth0 1606135006,[ 5.790000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth1): 9c:c7:a6:7e:c8:3b 1606135006,[ 5.800000] avmnet: avm_pa: register pid eth1 1606135006,[ 5.800000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth2): 9c:c7:a6:7e:c8:3f 1606135006,[ 5.810000] avmnet: avm_pa: register pid eth2 1606135006,[ 5.820000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth3): 9c:c7:a6:7e:c8:40 1606135006,[ 5.820000] avmnet: avm_pa: register pid eth3 1606135006,[ 5.830000] [avmnet_set_macaddr] Setup Mac Addr for Device(wasp): 00:de:ad:be:ef:ca 1606135006,[ 5.840000] [avmnet_create_netdevice] setup offload_cpu_link on device wasp 1606135006,[ 5.840000] avmnet: avm_pa: register pid wasp 1606135006,[ 5.890000] SQUASHFS error: Can't find a SQUASHFS superblock on mtdblock1 1606135006,[ 5.900000] yaffs: dev is 32505857 name is "mtdblock1" ro 1606135006,[ 5.900000] yaffs: passed flags "" 1606135006,[ 5.930000] VFS: Mounted root (yaffs filesystem) readonly on device 31:1. 1606135006,[ 5.940000] devtmpfs: mounted 1606135006,[ 5.940000] Freeing unused kernel memory: 300K (80835000 - 80880000) 1606135007,[ 7.030000] TFFS Name Table L 1606135007,[ ·.130000] yaffs: dev is 32505860 name is "mtdblock4" rw 1606135007,[ 7.130000] yaffs: passed flags "" 1606135009,[ 8.790000] [avm_urlader_env_set_variable] opening ID 0x1ae for writing 1606135009,[ 8.890000] led_modul_Fritz_Box_HW193: module license ' 1606135009,[ 8.890000] (C) Copyright 2012 by AVM 1606135009,[ 8.890000] ' taints kernel. 1606135009,[ 8.900000] Disabling lock debugging due to kernel taint 1606135009,[ 8.910000] [module-alloc-by-name] give 0x18000 bytes at 0x81104000 to module 'led_modul_Fritz_Box_HW193' (0xcdc000 bytes left) 1606135009,[ 8.930000] [LED] use GPIO 45 for 'gpio_avm_led_power' 1606135009,[ 8.930000] [LED] use GPIO 47 for 'gpio_avm_led_lan_all' 1606135009,[ 8.930000] [LED] use GPIO 36 for 'gpio_avm_led_wlan' 1606135009,[ 8.940000] [LED] use GPIO 35 for 'gpio_avm_led_pppoe' 1606135009,[ 8.940000] [LED] use GPIO 33 for 'gpio_avm_led_info' 1606135009,[ 8.950000] [BUTTON] use GPIO 29 for 'gpio_avm_button_wlan' 1606135009,[ 8.960000] [BUTTON] use GPIO 1 for 'gpio_avm_button_wps' 1606135009,[ 8.970000] AVM_WATCHDOG: System Init UEberwachung 120 Sekunden 1606135009,[ 9.370000] [module-alloc-by-name] give 0x3000 bytes at 0x8111c000 to module 'rtc_avm' (0xcd9000 bytes left) 1606135009,[ 9.380000] rtc-avm rtc-avm.0: rtc core: registered avm as rtc0 1606135009,[ 9.380000] [avm-rtc]: avm_rtc_probe: register: ret=0x87689000 1606135009,[ 9.390000] [avm-rtc]: avm_rtc_probe: success 1606135009,[ 9.590000] 1606135009,[ `9.590000] [avm_debug] redirecting kernel-messages (/dev/debug)


COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2020/12/06 10:21
  • by cocktailyogi