AVM FRITZ!Box 3390
Write a short, relevant description of the device. Include a technical overview, but avoid marketing buzzwords/useless stuff. Two to four sentences is about right. A picture is good, too. Edit the page to see how to add pictures.
Supported Versions
Works with the latest snapshot version.
If 2,4GHz support is needed, look at : https://www.aboehler.at/doku/doku.php/projects:fritz3390.
PR requests: https://github.com/openwrt/openwrt/pull/2662 and https://github.com/openwrt/openwrt/pull/3656
Hardware highlights
CPU | Ram | Flash | Network | WLAN | USB | Serial | JTag |
---|---|---|---|---|---|---|---|
Lantiq XWAY VRX288 | 128 MiB | 128 MiB | 4x 1Gbit | abgn | 2x 2.0 | 4pin Solderpads, 2.54mm, 3.3V, 115200 Baud | ? |
Installation
→ Install OpenWrt (generic explanation)
- Use the eva_ramboot.py script to load the initramfs image on the device. Run it a few seconds after turning the device on. If it fails to find the device try the ip address 169.254.120.1 (Firmware updates or the recovery tool apparently change it).
$ scripts/flashing eva_ramboot 192.168.178.1 bin/targets/lantiq/xrx200/avm_fritz3390-initramfs-kernel.bin
IMPORTANT: Set lzma compression in ramdisk options, bootloader stalls when receiving uncompressed images.
- The device will load the initramfs image in RAM and boot it.
- After booting the initramfs image, you can reach it under the OpenWrt default ip address 192.168.1.1.
- Check if the key
linux_fs_start
is not set to 1 in tffs
$ fritz_tffs_nand -d /dev/mtd1 -n linux_fs_start
If it is set to 1, the bootloader will select the wrong set of partitions. Passive ftp using ip: 192.168.178.1 login: adam2 password: adam2 and send
quote SETENV linux_fs_start 0
Afterwards start again at step 1.
- Run sysupgrade to persistently install OpenWrt.
Hardware
Info
Architecture | MIPS32 |
---|---|
Vendor | Lantiq |
Bootloader | EVA(AVM) Revision: 1.1660 Version: 2660 |
System-On-Chip | VR9: VRX288, Atheros AR9342 SoC |
CPU Cores | 2 |
CPU | MIPS 34Kc V1.2 2×500 Mhz |
xDSL | |
VoIP | via FRITZ!App Fon |
Flash-Chip | MICRON MT29F1G08ABADAWP, 2048 Pagesize 128k Blocksize 1024 Blocks 8Bit 1 CS HW |
Flash size | 128 MiB |
RAM | 128 MiB |
Wireless | AR9580 and AR9381 |
Switch | Soc-integrated |
DSL | Lantiq VRX288 + VRX206 |
USB | Yes 2 x 2.0 |
Serial | Yes |
JTAG | Yes |
Photos
Opening the case
Remove rubber feet and unscrew 4 screws Torx T9. Open case.
Serial
→ port.serial general information about the serial port, serial port cable, etc.
→ https://www.zebradem.com/wiki/index.php?title=Serielle_Konsole for information specific to Fritz!Boxes
How to connect to the Serial Port of this specific device:
Seen from the rear of the device, the most left of the 4 holes is square cut while the others are round.
Pin | 1 [ ] | 2 | 3 | 4 |
---|---|---|---|---|
Function | VCC | RX | TX | GND |
similar examples from Fritzbox 3370: Serial connectors holes, rear side.
Serial connection with a MAX3232/RS232 TTL to Serial Port Converter.
Serial connection parameters for FRITZ!Box 3390 | 115200, 8N1 |
---|
JTAG
→ port.jtag general information about the JTAG port, JTAG cable, etc.
How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port
Bootlogs
OEM bootlog
1606134986,ROM VER: 1.1.4 1606134986,CFG 05 1606134986,ç$ DC! ¤¥„„DC[-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\][|][/][-][\] 1606134988,(AVM) EVA Revision: 1.1660 Version: 2660 1606134988,(C) Copyright 2005 AVM Date: Apr 24 2013 Time: 12:33:43 (0) 3 0x0-0x740D 1606134988,[FLASH:] MACRONIX Uniform-Flash 256kB 256 Bytes WriteBuffer 1606134988,[FLASH:](Eraseregion [0] 4 sectors a 64kB) 1606134988,[NAND:] 128MB MICRON 2048 Pagesize 128k Blocksize 1024 Blocks 8Bit 1 CS HW 1606134988,[SYSTEM:] VR9 on 500MHz/250MHz/250MHz 1606134988,.Atheros 8030/35 detected 1606134988,Eva_AVM >................................................. 1606135000,Lantiq xDSL CPE VR9 1606135000,phym = 08000000, mem = 08000000, max_pfn = 00008000 1606135000,Reserving memory for CP1 @0xa8000000, size 0x00000000 1606135000,plat_device_tree_setup: AVM hardware subrevision 1 1606135000,plat_device_tree_setup: using Fallback device-tree of AVM hardware subrevision 0 1606135000,DT: d0 0d fe ed 00 00 0d f1 1606135000,[ 0.000000] Linux version 3.10.73 (jpluschke@EmbeddedVM) (gcc version 4.8.3 (Buildroot 2014.08) ) #1 SMP Wed Aug 21 17:10:32 CEST 2019 1606135000,[ 0.000000] [unv_init] 0x81017ad0[0] 1606135000,[ 0.000000] [env_init] 0x81017b10[1] 1606135000,[ 0.000000] [env_init] 0x81017c10[2] 1606135000,[ 0.000000] [env_init] switch to ram location 1606135000,[ 0.000000] [init_avm_kernel_config] AVM Kernel Config (ptr 80825000) 1606135000,[ 0.000000] [init_avm_kernel_config] AVM Kernel Config: module memory entry 1606135000,[ 0.000000] [init_avm_kernel_config] AVM Kernel Config: version info entry 1606135000,[ 0.000000] [init_avm_kernel_config] AVM Kernel Config: device-tree for subrev 0 found 1606135000,[ 0.000000] bootconsole [early0] enabled 1606135000,[ 0.000000] CPU0 revision is: 00019556 (MIPS 34Kc) 1606135000,[ 0.000000] Determined physical RAM map: 1606135000,[ 0.000000] memory: 08000000 @ 00000000 (usable) 1606135000,[ 0.000000] Initrd not found or empty - disabling initrd 1606135000,[ 0.000000] [module-alloc] use 0xcf4000 bytes at 0x81104000 1606135000,[ 0.000000] PERCPU: Embedded 7 pages/cpu @81dfc000 s7072 r8192 d13408 u32768 1606135000,[ 0.000000] Kernel command line: annex=B console=ttyS0,115200n8r nor_size=0MB sflash_size=256KB nand_size=128MB ethaddr=9C:C7:A6:7E:C8:3A 1606135000,[ 0.000000] [NAND] nand_size = 0x8000000 1606135000,[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) 1606135000,[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) 1606135000,[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) 1606135000,[ 0.000000] Writing ErrCtl register=00042200 1606135000,[ 0.000000] Readback ErrCtl register=00042200 1606135000,[ 0.000000] Memory: 107352k/131072k available (5707k kernel code, 23720k reserved, 2688k data, 300k init, 0k highmem) 1606135000,[ 0.000000] Hierarchical RCU implementation. 1606135000,[ 0.000000] NR_IRQS:181 1606135000,[ 0.000000] SRSConf0 0x3feffbfe: SRS1: 0xffffffff, SRS2 0xffffffff, SRS3 0xffffffff 1606135000,[ 0.000000] Lantiq ICU driver, version 3.0.1, (c) 2001-2011 Lantiq Deutschland GmbH 1606135000,[ 0.000000] Console: colour dummy device 80x25 1606135000,[ 0.000000] console [ttyS0] enabled, bootconsole disabled 1606135000,[ 0.000000] console [ttyS0] enabled, bootconsole disabled 1606135000,[ 0.020000] Calibrating delay loop... 331.77 BogoMIPS (lpj=1658880) 1606135000,[ 0.080000] pid_max: default: 32768 minimum: 301 1606135000,[ 0.080000] Security Framework initialized 1606135000,[ 0.080000] Mount-cache hash table entries: 512 1606135000,[ 0.090000] CPU1 revision is: 00019556 (MIPS 34Kc) 1606135000,[ 0.170000] Brought up 2 CPUs 1606135000,[ 0.170000] [yield_context_init] cpu=1 tc=2 mask=300 1606135000,[ 0.180000] [yield_context_init] cpu=0 tc=3 mask=410 1606135000,[ 0.180000] devtmpfs: initialized 1606135000,[ 0.200000] pinctrl core: initialized pinctrl subsystem 1606135000,[ 0.200000] Creating Config Table 1606135000,[ 0.200000] [avm_generate_hw_config_table_from_device_tree] gpio_cnt: 33 1606135000,[ 0.210000] NET: Registered protocol family 16 1606135000,[ 0.220000] Reboot Status is: Power-On 1606135000,[ 0.220000] [TFFS3_Early_Init] called 1606135000,[ 0.230000] [avmnet] [avmnet_cfg_init] Driver version: 6.221.2.4 - Revision 1496:3477 - Mi 21. Aug 17:09:45 CEST 2019 1606135001,[ 0.850000] Lantiq PCIe Root Complex driver, version 2.0.0, (c) 2001-2011 Lantiq Deutschland GmbH 1606135001,[ 0.900000] bio: create slab <bio-0> at 0 1606135001,[ 0.900000] PCI host bridge to bus 0000:00 1606135001,[ 0.910000] pci_bus 0000:00: root bus resource [mem 0x1c000000-0x1cffffff] 1606135001,[ 0.910000] pci_bus 0000:00: root bus resource [io 0x1d800000-0x1d8fffff] 1606135001,[ 0.920000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] 1606135001,[ 0.930000] ifx_pcie_rc_class_early_fixup port 0: fixed pcie host bridge to pci-pci bridge 1606135001,[ 0.940000] pci 0000:00:00.0: BAR 8: assigned [mem 0x1c000000-0x1c0fffff] 1606135001,[ 0.940000] pci 0000:00:00.0: BAR 9: assigned [mem 0x1c100000-0x1c1fffff pref] 1606135001,[ 0.950000] pci 0000:01:00.0: BAR 0: assigned [mem 0x1c000000-0x1c01ffff 64bit] 1606135001,[ 0.950000] pci 0000:01:00.0: BAR 6: assigned [mem 0x1c100000-0x1c10ffff pref] 1606135001,[ 0.960000] pci 0000:00:00.0: PCI bridge to [bus 01] 1606135001,[ 0.960000] pci 0000:00:00.0: bridge window [mem 0x1c000000-0x1c0fffff] 1606135001,[ 0.970000] pci 0000:00:00.0: bridge window [mem 0x1c100000-0x1c1fffff pref] 1606135001,[ 0.970000] NET: Registered protocol family 8 1606135001,[ 0.980000] NET: Registered protocol family 20 1606135001,[ 0.980000] Switching to clocksource MIPS 1606135001,[ 1.030000] NET: Registered protocol family 2 1606135001,[ 1.030000] TCP established hash table entries: 1024 (order: 1, 8192 bytes) 1606135001,[ 1.040000] TCP bind hash table entries: 1024 (order: 1, 8192 bytes) 1606135001,[ 1.040000] TCP: Hash tables configured (established 1024 bind 1024) 1606135001,[ 1.050000] TCP: reno registered 1606135001,[ 1.050000] UDP hash table entries: 256 (order: 1, 8192 bytes) 1606135001,[ 1.060000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) 1606135001,[ 1.070000] NET: Registered protocol family 1 1606135001,[ 1.070000] Lantiq CGU driver, version 1.1.32, (c) 2001-2011 Lantiq Deutschland GmbH 1606135001,[ 1.080000] IFX DMA driver, version ifxmips_dma_core.c:v1.0.17, (c) 2009 Infineon Technologies AG 1606135001,[ 1.080000] skb_shared_size:184 1606135001,[ 1.090000] squashfs: version 4.0 (2009/01/31) Phillip Lougher 1606135001,[ 1.100000] fuse init (API version 7.22) 1606135001,[ 1.104000] msgmni has been set to 209 1606135001,[ 1.110000] io scheduler noop registered (default) 1606135001,[ 1.450000] ttyS0 at MMIO 0x1e300c00 (irq = 107) is a PORT_IFX_ASC 1606135001,[ 1.450000] ifx_usif_uart_init: uart_register_driver failed 1606135001,[ 1.460000] avm_net_trace: Up and running. 1606135001,[ 1.460000] [loadcontrol] set auto - scale=1 1606135001,[ 1.470000] Lantiq Thermal Sensor driver, version 1.0.3, (c) 2001-2011 Lantiq Deutschland GmbH 1606135001,[ 1.480000] ifx_pmu_init: Major 244 1606135001,[ 1.480000] Lantiq PMU driver, version 1.2.6, (c) 2001-2011 Lantiq Deutschland GmbX 1606135001,[ 1.490000] Lantiq GPIO driver, version 1.3.2, (c) 2001-2011 Lantiq Deutschland GmbH 1606135001,[ 1.500000] Infineon Technologies RCU driver version 1.0.7 1606135001,[ 1.520000] loop: module loaded 1606135001,[ 1.520000] nbd: registered device at major!43 1606135001,[ 1.550000] [HSNAND] Hardware-ECC activated 1606135001,[ 01.550000] ONFI param page 0 valid 1606135001,[ 1.560000] ONFI flash detected 1606135001,[ 1.560000] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xf1 (Micron MT29F1G08ABADAWP), 128MiB, page size: 2048, OOB size: 64 1606135001,[ 1.570000] Scanning device for bad blocks 1606135001,[ 1.590000] [ifx_hsnand_command] read block is critical (column: 0x800 page: 0x2c80) 1606135002,[ 1.670000] Creating 6 MTD partitions on "ifx_hsnand": 1606135002,[ 1.670000] 0x000000000000-0x000000400000 : "kernel" 1606135002,[ 1.680000] 0x000000400000-0x000003400000 : "filesystem" 1606135002,[ 1.690000] 0x000003400000-0x000003800000 : "reserved-kernel" 1606135002,[ 1.690000] 0x000003800000-0x000006800000 : "reserved-filesystem" 1606135002,[ 1.700000] 0x000006800000-0x000006a00000 : "config" 1606135002,[ 1.710000] 0x000006a00000-0x000008000000 : "nand-filesystem" 1606135002,[ 1.720000] [TFFS3_Register_Panic_CB] registering panic callback for mtd ifx_hsnand 1606135002,[ 1.720000] [TFFS3_Register_Panic_CB] registering panic callback for mtd ifx_sflash 1606135002,[ 1.730000] Creating 3 MTD partitions on "ifx_sflash": 1606135002,[ 1.740000] 0x000000000000-0x000000020000 : "urlader" 1606135002,[ 1.740000] 0x000000020000-0x000000030000 : "tffs (1)" 1606135002,[ 1.750000] 0x000000030000-0x000000040000 : "tffs (2)" 1606135002,[ 1.760000] Lantiq SPI flash driver, version 2.0.1, (c) 2001-2011 Lantiq Deutschland GmbH 1606135002,[ 1.760000] tun: Universal TUN/TAP device driver, 1.6 1606135002,[ 1.770000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> 1606135002,[ 1.780000] SWAPI: Registered character device [switch_api] with major no [81] 1606135002,[ 1.780000] i2c /dev entries driver 1606135002,[ 1.790000] cpuidle: using governor ladder 1606135002,[ 1.790000] cpuidle: using governor menu 1606135002,Š[ 1.790000] AVM PA 4.3.14 2015-10-21 1606135002,[ 1.800000] AVM PA skb pktinfo at offset 136 size 196 1606135002,[ 1.800000] [loadcontrol]module avm_pa registered 1606135002,[ 1.810000] ipip: IPv4 over IPv4 tunneling driver 1606135002,[ 1.810000] TCP: cubic registered 1606135002,[ 1.820000] NET: Registered protocol family 10 1606135002,[ 1.820000] sit: IPv6 over IPv4 tunneling driver 1606135002,[ 1.830000] NET: Registered protocol family 17 1606135002,[ 1.830000] l2tp_core: L2TP core driver, V2.0 1606135002,[ 1.830000] l2tp_ip: L2TP IP encapsulation support (L2TPv3) 1606135002,[ 1.840000] l2tp_netlink: L2TP netlink interface 1606135002,[ 1.840000] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3) 1606135002,[ 1.850000] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3) 1606135002,[ 1.860000] 8021q: 802.1Q VLAN Support v1.8 1606135002,[ 1.860000] Key type dns_resolver registered 1606135002,[ 1.870000] <ifx_fix_timing> 1606135002,[ 1.870000] [TFFS3_Init] No!storage module registered, trying legacy fallback 1606135002,[ 1.880000] [TFFS3_Register_LGCY] Called 1606135002,[ 1.880000] [TFFS3_LGCY_Configure] Called 1606135002,[ 1.890000] [TFFS3_LGCY_Setup] using mtd7(tffs (1)), mtd8(tffs (2)) 1606135002,[ 1.890000] [TFFS3_LGCY_Setup] mtd "tffs (1)": segment value 1 1606135002,[ 1.900000] [TFFS3_LGCY_Setup] mtd "tffs (2)": segment value 1 1606135002,[ 1.900000] [TFFS3_LGCY_Setup] Using segment 1 (avail: 1 + 1) 1606135002,[ 1.910000] [TFFS3_LGCY_Setup] mtd8 size=0x10000 1606135002,[ 1.910000] TFFS: tiny flash file system driver. GPL (c) AVM Berlin (Version 3.0) 1606135002,[ 1.910000] [rescan_segment] Called with mode=2 1606135002,[ 1.910000] TFFS: Clearing index for update 1606135002,[ 1.930000] Adam2 environment variables API installed. 1606135002,[ 1.940000] [simple-profiling]: 2 performance counters implemented, NEW_34K 1606135002,[ 1.940000] Enable Performance Counter 0 for Data cache load/stores (User-Mode enabled Supervisor-Mode enabled Kernel-Mode enabled Exeption-Mode disable) 1606135002,[ 1.960000] Setup tcs=0x2 current_tc_mask=0x2, reg=0 1606135002,[ 1.960000] [simple-profiling]: 2 performance counters implemented, NEW_34K 1606135002,[ 1.970000] Enable Performance Counter 1 for Data cache load/store mi{ses (User-Mode enabled Supervisor-Mode enabled Kernel-Mode enabled Exeption-Mode disable) 1606135002,[ 1.980000] Setup tcs=0x2 current_tc_mask=0x2, reg=1 1606135002,[ 1.990000] {avmnet_cfg_netinit} 1606135002,[ 1.990000] [avmnet] No config found for HWRev 193, HWSubRev 1, Profile-ID 0, trying base config for HWSubRev 1606135002,[ 2.000000] [avmnet] No config found for HWRev 193, HWSubRev 1, trying base config for HWRev 1606135002,[ 2.010000] [avmnet] [avmnet_swi_7port_init] Init on module swi_vr9 called. 1606135002,[ 2.330000] [ppe_eth_init] init_hw() 1606135002,[ 2.340000] [init_hw] ppe_hw_init=0xff successful 1606135002,[ 2.340000] [ppe_eth_init] ifx_proc_file_create() 1606135002,[ 2.340000] [ppe_eth_init] dma_setup_init() 1606135002,[ 2.350000] [avmnet] [avmnet_swi_7port_disable_learning] Configuring CPU-port to receive all unknown unicast frames 0x48 1606135002,[ 2.360000] [avmnet] [avmnet_swi_7port_disable_learning] Configuring CPU-port to receive all unknown multicast frames 0x48 1606135006,[ 5.780000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth0): 9c:c7:a6:7e:c8:3a 1606135006,[ 5.790000] avmnet: avm_pa: register pid eth0 1606135006,[ 5.790000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth1): 9c:c7:a6:7e:c8:3b 1606135006,[ 5.800000] avmnet: avm_pa: register pid eth1 1606135006,[ 5.800000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth2): 9c:c7:a6:7e:c8:3f 1606135006,[ 5.810000] avmnet: avm_pa: register pid eth2 1606135006,[ 5.820000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth3): 9c:c7:a6:7e:c8:40 1606135006,[ 5.820000] avmnet: avm_pa: register pid eth3 1606135006,[ 5.830000] [avmnet_set_macaddr] Setup Mac Addr for Device(wasp): 00:de:ad:be:ef:ca 1606135006,[ 5.840000] [avmnet_create_netdevice] setup offload_cpu_link on device wasp 1606135006,[ 5.840000] avmnet: avm_pa: register pid wasp 1606135006,[ 5.890000] SQUASHFS error: Can't find a SQUASHFS superblock on mtdblock1 1606135006,[ 5.900000] yaffs: dev is 32505857 name is "mtdblock1" ro 1606135006,[ 5.900000] yaffs: passed flags "" 1606135006,[ 5.930000] VFS: Mounted root (yaffs filesystem) readonly on device 31:1. 1606135006,[ 5.940000] devtmpfs: mounted 1606135006,[ 5.940000] Freeing unused kernel memory: 300K (80835000 - 80880000) 1606135007,[ 7.030000] TFFS Name Table L 1606135007,[ ·.130000] yaffs: dev is 32505860 name is "mtdblock4" rw 1606135007,[ 7.130000] yaffs: passed flags "" 1606135009,[ 8.790000] [avm_urlader_env_set_variable] opening ID 0x1ae for writing 1606135009,[ 8.890000] led_modul_Fritz_Box_HW193: module license ' 1606135009,[ 8.890000] (C) Copyright 2012 by AVM 1606135009,[ 8.890000] ' taints kernel. 1606135009,[ 8.900000] Disabling lock debugging due to kernel taint 1606135009,[ 8.910000] [module-alloc-by-name] give 0x18000 bytes at 0x81104000 to module 'led_modul_Fritz_Box_HW193' (0xcdc000 bytes left) 1606135009,[ 8.930000] [LED] use GPIO 45 for 'gpio_avm_led_power' 1606135009,[ 8.930000] [LED] use GPIO 47 for 'gpio_avm_led_lan_all' 1606135009,[ 8.930000] [LED] use GPIO 36 for 'gpio_avm_led_wlan' 1606135009,[ 8.940000] [LED] use GPIO 35 for 'gpio_avm_led_pppoe' 1606135009,[ 8.940000] [LED] use GPIO 33 for 'gpio_avm_led_info' 1606135009,[ 8.950000] [BUTTON] use GPIO 29 for 'gpio_avm_button_wlan' 1606135009,[ 8.960000] [BUTTON] use GPIO 1 for 'gpio_avm_button_wps' 1606135009,[ 8.970000] AVM_WATCHDOG: System Init UEberwachung 120 Sekunden 1606135009,[ 9.370000] [module-alloc-by-name] give 0x3000 bytes at 0x8111c000 to module 'rtc_avm' (0xcd9000 bytes left) 1606135009,[ 9.380000] rtc-avm rtc-avm.0: rtc core: registered avm as rtc0 1606135009,[ 9.380000] [avm-rtc]: avm_rtc_probe: register: ret=0x87689000 1606135009,[ 9.390000] [avm-rtc]: avm_rtc_probe: success 1606135009,[ 9.590000] 1606135009,[ `9.590000] [avm_debug] redirecting kernel-messages (/dev/debug)
OpenWrt bootlog
COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING