Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| inbox:toh:arcadyan:astoria:we420223-99 [2022/10/09 19:11] – WIP harm | inbox:toh:arcadyan:astoria:we420223-99 [2023/05/18 16:51] – [Flashing via the original web interface] Fix list harm | ||
|---|---|---|---|
| Line 7: | Line 7: | ||
| ===== OpenWrt support ===== | ===== OpenWrt support ===== | ||
| - | Official support | + | There is no stable release yet that supports this device, there are snapshot releases though. |
| - | * Patchwork patch: https:// | ||
| - | * GitHub fork: https:// | ||
| * OpenWrt forum thread: https:// | * OpenWrt forum thread: https:// | ||
| * Tweakers forum thread: https:// | * Tweakers forum thread: https:// | ||
| Line 25: | Line 23: | ||
| ===== Installation ===== | ===== Installation ===== | ||
| - | This device | + | If you are running an old firmware version that is equipped with a firmware upload page, that is usable for upgrading to OpenWRT, |
| - | < | + | |
| - | Target System (MediaTek Ralink MIPS) | + | |
| - | Subtarget (MT7621 based boards) | + | |
| - | Target Profile (Arcadyan WE420223-99) | + | |
| - | </ | + | |
| - | Or ask for a build in the forum thread. | + | |
| - | Unfortunately, the official firmware' | + | Otherwise, we need to directly write to the flash chip since the official firmware' |
| - | ==== Connecting | + | ==== Flashing via the original web interface |
| - | A Raspberry Pi can be used to program the flash chip in-circuit (thanks FPSUsername for discovering). Connect the chip directly to the Raspberry Pi's SPI pins. You can solder wires to the flash chip but using a [[https:// | + | |
| - | On the Raspberry Pi, you can use a specially crafted overlay for accessing the chip: https://gist.github.com/ | + | The original firmware requires signed firmware. The code to do so is on GitHub: https:// |
| - | Download this file and install it with '' | + | - Flash the signed image via the web interface. OpenWRT should boot and start a DHCP server. |
| + | - Go to http:// | ||
| + | - Profit! You might still want to unlock the U-Boot password for recovery in the future (see below) | ||
| + | ==== Writing directly to the flash chip ==== | ||
| + | === Connecting the flash chip to a Raspberry Pi === | ||
| + | A Raspberry Pi can be used to program the flash chip in-circuit (thanks FPSUsername for discovering). On the Raspberry Pi, install '' | ||
| Enable it in ''/ | Enable it in ''/ | ||
| + | |||
| + | Connect the chip directly to the Raspberry Pi's SPI pins. Use the following connections: | ||
| + | |||
| + | {{: | ||
| + | |||
| + | ^ Flash Chip ^ Raspberry Pi ^ | ||
| + | | VCC | 3v3 | | ||
| + | | RESET | 3v3 | | ||
| + | | /CS | GPIO 8 (SPI0 CE0) | | ||
| + | | DO | GPIO 9 (SPI0 MISO) | | ||
| + | | CLK | GPIO11 (SPI0 SCLK) | | ||
| + | | DI | GPIO 10 (SPI0 MOSI) | | ||
| + | | GND | Ground | ||
| + | |||
| + | You can solder wires to the flash chip but using a [[https:// | ||
| After connecting the flash chip and rebooting, the ''/ | After connecting the flash chip and rebooting, the ''/ | ||
| - | ==== Creating a backup | + | === Creating a backup === |
| For recovery, creating a backup of the flash is recommended. Run '' | For recovery, creating a backup of the flash is recommended. Run '' | ||
| - | ==== Unlocking U-Boot | + | === Unlocking U-Boot === |
| - | The password of U-Boot can be removed, though this step is optional. The following script will unlock U-Boot: | + | The password of U-Boot can be removed, though this step is optional. It is particularly useful for recovering the device through the serial port (i.e. booting an OpenWrt initramfs). The following script will unlock U-Boot: |
| < | < | ||
| Line 69: | Line 80: | ||
| </ | </ | ||
| - | ==== Flashing OpenWRT | + | === Flashing OpenWRT === |
| - | After building OpenWRT, you should have a `.trx` file containing the kernel and ubifs. | + | First we make sure the u-boot |
| < | < | ||
| echo '/ | echo '/ | ||
| Line 76: | Line 87: | ||
| </ | </ | ||
| - | Now flash it with '' | + | Download the latest '' |
| + | Now flash it with '' | ||
| ===== Debricking ===== | ===== Debricking ===== | ||
| Line 153: | Line 164: | ||
| ^ Interface Name ^ Description | ^ Interface Name ^ Description | ||
| | br-lan | | br-lan | ||
| - | | lan0 | Left port (viewed from back) | Attached to br-lan | + | | swp0 | Left port (viewed from back) | Attached to br-lan |
| - | | lan1 | Right port (viewed from back)| Attached to br-lan | + | | swp1 | Right port (viewed from back)| Attached to br-lan |
| | wlan0 | 2.4GHz WiFi | Disabled | | wlan0 | 2.4GHz WiFi | Disabled | ||
| | wlan1 | 5GHz WiFi | Disabled | | wlan1 | 5GHz WiFi | Disabled | ||
| Line 1079: | Line 1090: | ||
| ==== OpenWrt bootlog ==== | ==== OpenWrt bootlog ==== | ||
| <WRAP bootlog> | <WRAP bootlog> | ||
| - | < | + | < |
| + | =================================================================== | ||
| + | | ||
| + | | ||
| + | ================================================================== | ||
| + | Change MPLL source from XTAL to CR... | ||
| + | do MEMPLL setting.. | ||
| + | MEMPLL Config : 0x11100000 | ||
| + | 3PLL mode + External loopback | ||
| + | === XTAL-40Mhz === DDR-1200Mhz === | ||
| + | PLL4 FB_DL: 0x3, 1/0 = 571/453 0D000000 | ||
| + | PLL3 FB_DL: 0x11, 1/0 = 600/424 45000000 | ||
| + | PLL2 FB_DL: 0x15, 1/0 = 611/413 55000000 | ||
| + | do DDR setting..[01F40000] | ||
| + | Apply DDR3 Setting...(use customer AC) | ||
| + | 0 8 | ||
| + | -------------------------------------------------------------------------------- | ||
| + | 0000: | ||
| + | 0001: | ||
| + | 0002: | ||
| + | 0003: | ||
| + | 0004: | ||
| + | 0005: | ||
| + | 0006: | ||
| + | 0007: | ||
| + | 0008: | ||
| + | 0009: | ||
| + | 000A: | ||
| + | 000B: | ||
| + | 000C: | ||
| + | 000D: | ||
| + | 000E: | ||
| + | 000F: | ||
| + | 0010: | ||
| + | 0011: | ||
| + | 0012: | ||
| + | 0013: | ||
| + | 0014: | ||
| + | 0015: | ||
| + | 0016: | ||
| + | 0017: | ||
| + | 0018: | ||
| + | 0019: | ||
| + | 001A: | ||
| + | 001B: | ||
| + | 001C: | ||
| + | 001D: | ||
| + | 001E: | ||
| + | 001F: | ||
| + | rank 0 coarse = 15 | ||
| + | rank 0 fine = 72 | ||
| + | B:| 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 | ||
| + | opt_dle value:11 | ||
| + | DRAMC_R0DELDLY[018]=00001F1F | ||
| + | ================================================================== | ||
| + | RX DQS perbit delay software calibration | ||
| + | ================================================================== | ||
| + | 1.0-15 bit dq delay value | ||
| + | ================================================================== | ||
| + | bit| | ||
| + | -------------------------------------- | ||
| + | 0 | 9 7 8 10 7 8 8 7 8 8 | ||
| + | 10 | 9 10 9 12 9 10 | ||
| + | -------------------------------------- | ||
| + | |||
| + | ================================================================== | ||
| + | 2.dqs window | ||
| + | x=pass dqs delay value (min~max)center | ||
| + | y=0-7bit DQ of every group | ||
| + | input delay:DQS0 =31 DQS1 = 31 | ||
| + | ================================================================== | ||
| + | bit DQS0 bit | ||
| + | 0 (1~58)29 | ||
| + | 1 (1~58)29 | ||
| + | 2 (1~59)30 | ||
| + | 3 (1~60)30 | ||
| + | 4 (1~59)30 | ||
| + | 5 (1~60)30 | ||
| + | 6 (1~60)30 | ||
| + | 7 (1~61)31 | ||
| + | ================================================================== | ||
| + | 3.dq delay value last | ||
| + | ================================================================== | ||
| + | bit| 0 1 2 3 4 5 6 7 8 9 | ||
| + | -------------------------------------- | ||
| + | 0 | 11 9 9 11 8 9 9 7 10 10 | ||
| + | 10 | 10 12 10 13 9 11 | ||
| + | ================================================================== | ||
| + | ================================================================== | ||
| + | | ||
| + | ================================================================== | ||
| + | DQS loop = 15, cmp_err_1 = ffff0000 | ||
| + | dqs_perbyte_dly.last_dqsdly_pass[0]=15, | ||
| + | dqs_perbyte_dly.last_dqsdly_pass[1]=15, | ||
| + | DQ loop=15, cmp_err_1 = ffff00aa | ||
| + | dqs_perbyte_dly.last_dqdly_pass[1]=15, | ||
| + | DQ loop=14, cmp_err_1 = ffff00a0 | ||
| + | DQ loop=13, cmp_err_1 = ffff0080 | ||
| + | DQ loop=12, cmp_err_1 = ffff0000 | ||
| + | dqs_perbyte_dly.last_dqdly_pass[0]=12, | ||
| + | byte:0, (DQS, | ||
| + | byte:1, (DQS, | ||
| + | 20, | ||
| + | [EMI] DRAMC calibration passed | ||
| + | |||
| + | =================================================================== | ||
| + | | ||
| + | | ||
| + | =================================================================== | ||
| + | |||
| + | |||
| + | U-Boot 1.1.3 (Dec 4 2017 - 11:37:57) 0.00 | ||
| + | |||
| + | Board: Ralink APSoC DRAM: 128 MB | ||
| + | relocate_code Pointer at: 87f94000 | ||
| + | |||
| + | Config XHCI 40M PLL | ||
| + | ****************************** | ||
| + | Software System Reset Occurred | ||
| + | ****************************** | ||
| + | flash manufacture id: c2, device id 20 19 | ||
| + | find flash: MX25L25635E | ||
| + | ============================================ | ||
| + | Ralink UBoot Version: 5.0.0.1 | ||
| + | -------------------------------------------- | ||
| + | ASIC MT7621A DualCore (MAC to MT7530 Mode) | ||
| + | DRAM_CONF_FROM: | ||
| + | DRAM_TYPE: DDR3 | ||
| + | DRAM bus: 16 bit | ||
| + | Xtal Mode=3 OCP Ratio=1/3 | ||
| + | Flash component: 32 MBytes NOR Flash | ||
| + | Date: | ||
| + | ============================================ | ||
| + | icache: sets:256, ways:4, linesz:32 , | ||
| + | dcache: sets:256, ways:4, linesz:32 , | ||
| + | |||
| + | ##### The CPU freq = 880 MHZ #### | ||
| + | | ||
| + | # | ||
| + | set LAN/WAN LLLLW | ||
| + | |||
| + | Please choose the operation: | ||
| + | 1: Load system code to SDRAM via TFTP. | ||
| + | 2: Load system code then write to Flash via TFTP. | ||
| + | 3: Boot system code via Flash (default). | ||
| + | 4: Entr boot command line interface. | ||
| + | 7: Load Boot Loader code then write to Flash via Serial. | ||
| + | 9: Load Boot Loader code then write to Flash via TFTP. | ||
| + | default: 3 0 | ||
| + | |||
| + | 3: System Boot system code via Flash[0]. | ||
| + | ## Booting image at bc050000 ... | ||
| + | old glbcfg partition is broken, magic=[0x23494255][0x55424923]! | ||
| + | | ||
| + | Image Name: MIPS OpenWrt Linux-5.10.161 | ||
| + | Image Type: MIPS Linux Kernel Image (uncompressed) | ||
| + | Data Size: 2692535 Bytes = 2.6 MB | ||
| + | Load Address: 80001000 | ||
| + | Entry Point: | ||
| + | | ||
| + | OK | ||
| + | No initrd | ||
| + | ## Transferring control to Linux (at address 80001000) ... | ||
| + | ## Giving linux memsize in MB, 128 | ||
| + | |||
| + | Starting kernel ... | ||
| + | |||
| + | |||
| + | |||
| + | OpenWrt kernel loader for MIPS based SoC | ||
| + | Copyright (C) 2011 Gabor Juhos < | ||
| + | Decompressing kernel... done! | ||
| + | Starting kernel at 80001000... | ||
| + | |||
| + | [ 0.000000] Linux version 5.10.161 (builder@buildhost) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.3.0 r21603+2-fb15cb4ce9) 11.3.0, GNU ld (GNU Binutils) 2.37) #0 SMP Tue Dec 27 14:26:24 2022 | ||
| + | [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3 | ||
| + | [ 0.000000] printk: bootconsole [early0] enabled | ||
| + | [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) | ||
| + | [ 0.000000] MIPS: machine is Arcadyan WE420223-99 | ||
| + | [ 0.000000] Initrd not found or empty - disabling initrd | ||
| + | [ 0.000000] VPE topology {2,2} total 4 | ||
| + | [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. | ||
| + | [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes | ||
| + | [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. | ||
| + | [ 0.000000] Zone ranges: | ||
| + | [ 0.000000] | ||
| + | [ 0.000000] | ||
| + | [ 0.000000] Movable zone start for each node | ||
| + | [ 0.000000] Early memory node ranges | ||
| + | [ 0.000000] | ||
| + | [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] | ||
| + | [ 0.000000] percpu: Embedded 15 pages/cpu s30480 r8192 d22768 u61440 | ||
| + | [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480 | ||
| + | [ 0.000000] Kernel command line: console=ttyS0, | ||
| + | [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) | ||
| + | [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) | ||
| + | [ 0.000000] Writing ErrCtl register=00000000 | ||
| + | [ 0.000000] Readback ErrCtl register=00000000 | ||
| + | [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off | ||
| + | [ 0.000000] Memory: 119472K/ | ||
| + | [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, | ||
| + | [ 0.000000] rcu: Hierarchical RCU implementation. | ||
| + | [ 0.000000] Tracing variant of Tasks RCU enabled. | ||
| + | [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. | ||
| + | [ 0.000000] NR_IRQS: 256 | ||
| + | [ 0.000000] CPU Clock: 880MHz | ||
| + | [ 0.000000] clocksource: | ||
| + | [ 0.000013] sched_clock: | ||
| + | [ 0.015854] clocksource: | ||
| + | [ 0.033809] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688) | ||
| + | [ 0.106131] pid_max: default: 32768 minimum: 301 | ||
| + | [ 0.115443] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) | ||
| + | [ 0.129849] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) | ||
| + | [ 0.148140] rcu: Hierarchical SRCU implementation. | ||
| + | [ 0.157952] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build | ||
| + | [ 0.173529] smp: Bringing up secondary CPUs ... | ||
| + | [ 0.183279] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. | ||
| + | [ 0.183290] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes | ||
| + | [ 0.183301] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. | ||
| + | [ 0.183376] CPU1 revision is: 0001992f (MIPS 1004Kc) | ||
| + | [ 0.243361] Synchronize counters for CPU 1: done. | ||
| + | [ 0.305528] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. | ||
| + | [ 0.305537] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes | ||
| + | [ 0.305545] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. | ||
| + | [ 0.305593] CPU2 revision is: 0001992f (MIPS 1004Kc) | ||
| + | [ 0.364493] Synchronize counters for CPU 2: done. | ||
| + | [ 0.424841] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. | ||
| + | [ 0.424850] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes | ||
| + | [ 0.424858] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. | ||
| + | [ 0.424912] CPU3 revision is: 0001992f (MIPS 1004Kc) | ||
| + | [ 0.484074] Synchronize counters for CPU 3: done. | ||
| + | [ 0.543685] smp: Brought up 1 node, 4 CPUs | ||
| + | [ 0.556200] clocksource: | ||
| + | [ 0.575716] futex hash table entries: 1024 (order: 3, 32768 bytes, linear) | ||
| + | [ 0.589534] pinctrl core: initialized pinctrl subsystem | ||
| + | [ 0.602231] NET: Registered protocol family 16 | ||
| + | [ 0.612267] thermal_sys: | ||
| + | [ 0.613296] cpuidle: using governor teo | ||
| + | [ 0.638657] rt2880-pinmux pinctrl: there is not valid maps for state default | ||
| + | [ 0.683299] clocksource: | ||
| + | [ 0.695156] NET: Registered protocol family 2 | ||
| + | [ 0.704010] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear) | ||
| + | [ 0.719695] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) | ||
| + | [ 0.736368] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) | ||
| + | [ 0.751484] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear) | ||
| + | [ 0.765484] TCP: Hash tables configured (established 1024 bind 1024) | ||
| + | [ 0.778246] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) | ||
| + | [ 0.791129] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) | ||
| + | [ 0.805229] NET: Registered protocol family 1 | ||
| + | [ 0.813806] PCI: CLS 0 bytes, default 32 | ||
| + | [ 0.823874] workingset: timestamp_bits=14 max_order=15 bucket_order=1 | ||
| + | [ 0.841029] squashfs: version 4.0 (2009/ | ||
| + | [ 0.852578] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. | ||
| + | [ 0.873035] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) | ||
| + | [ 0.889474] mt7621_gpio 1e000600.gpio: | ||
| + | [ 0.900824] mt7621_gpio 1e000600.gpio: | ||
| + | [ 0.912094] mt7621_gpio 1e000600.gpio: | ||
| + | [ 0.923818] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled | ||
| + | [ 0.940573] printk: console [ttyS0] disabled | ||
| + | [ 0.949067] 1e000c00.uartlite: | ||
| + | [ 0.966996] printk: console [ttyS0] enabled | ||
| + | [ 0.966996] printk: console [ttyS0] enabled | ||
| + | [ 0.983535] printk: bootconsole [early0] disabled | ||
| + | [ 0.983535] printk: bootconsole [early0] disabled | ||
| + | [ 1.005547] spi-mt7621 1e000b00.spi: | ||
| + | [ 1.017892] spi-nor spi0.0: mx25l25635e (32768 Kbytes) | ||
| + | [ 1.028295] 12 fixed-partitions partitions found on MTD device spi0.0 | ||
| + | [ 1.041148] Creating 12 MTD partitions on " | ||
| + | [ 1.050884] 0x000000000000-0x000002000000 : " | ||
| + | [ 1.061216] 0x000000000000-0x000000030000 : " | ||
| + | [ 1.072829] 0x000000030000-0x000000040000 : " | ||
| + | [ 1.083807] 0x000000040000-0x000000050000 : " | ||
| + | [ 1.094885] 0x000000050000-0x000001fb0000 : " | ||
| + | [ 1.105803] 0x000000490000-0x000001fb0000 : " | ||
| + | [ 1.116620] mtd: setting mtd5 (rootfs) as root device | ||
| + | [ 1.126800] mtdsplit: no squashfs found in " | ||
| + | [ 1.136564] 0x000001000000-0x000001fb0000 : " | ||
| + | [ 1.147590] 0x000001440000-0x000001fb0000 : " | ||
| + | [ 1.158715] 0x000001fb0000-0x000001fc0000 : " | ||
| + | [ 1.169716] 0x000001fc0000-0x000001fd0000 : " | ||
| + | [ 1.181486] 0x000001fd0000-0x000001fe0000 : " | ||
| + | [ 1.192745] 0x000001fe0000-0x000001ff0000 : " | ||
| + | [ 1.254756] mt7530 mdio-bus: | ||
| + | [ 1.270802] mtk_soc_eth 1e100000.ethernet: | ||
| + | [ 1.287960] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 20 | ||
| + | [ 1.304794] mtk_soc_eth 1e100000.ethernet: | ||
| + | [ 1.321891] mtk_soc_eth 1e100000.ethernet swp0: mediatek frame engine at 0xbe100000, irq 20 | ||
| + | [ 1.339883] i2c /dev entries driver | ||
| + | [ 1.349384] mt7621-pci 1e140000.pcie: | ||
| + | [ 1.362784] mt7621-pci 1e140000.pcie: | ||
| + | [ 1.380312] mt7621-pci 1e140000.pcie: | ||
| + | [ 1.396622] mt7621-pci 1e140000.pcie: | ||
| + | [ 1.413013] mt7621-pci 1e140000.pcie: | ||
| + | [ 1.425752] NET: Registered protocol family 10 | ||
| + | [ 1.436434] Segment Routing with IPv6 | ||
| + | [ 1.443902] NET: Registered protocol family 17 | ||
| + | [ 1.452830] bridge: filtering via arp/ | ||
| + | [ 1.479010] 8021q: 802.1Q VLAN Support v1.8 | ||
| + | [ 1.490791] mt7530 mdio-bus: | ||
| + | [ 1.523677] mt7530 mdio-bus:1f swp1 (uninitialized): | ||
| + | [ 1.547639] mt7530 mdio-bus: | ||
| + | [ 1.564450] DSA: tree 0 setup | ||
| + | [ 1.570659] rt2880-pinmux pinctrl: pcie is already enabled | ||
| + | [ 1.581673] mt7621-pci 1e140000.pcie: | ||
| + | [ 1.595051] mt7621-pci 1e140000.pcie: | ||
| + | [ 1.612586] mt7621-pci 1e140000.pcie: | ||
| + | [ 1.628889] mt7621-pci 1e140000.pcie: | ||
| + | [ 1.645286] mt7621-pci-phy 1e149000.pcie-phy: | ||
| + | [ 1.660381] mt7621-pci-phy 1e14a000.pcie-phy: | ||
| + | [ 1.675378] mt7621-pci 1e140000.pcie: | ||
| + | [ 1.790050] mt7621-pci-phy 1e149000.pcie-phy: | ||
| + | [ 1.801174] mt7621-pci-phy 1e14a000.pcie-phy: | ||
| + | [ 1.912472] mt7621-pci 1e140000.pcie: | ||
| + | [ 1.926353] mt7621-pci 1e140000.pcie: | ||
| + | [ 1.940216] mt7621-pci 1e140000.pcie: | ||
| + | [ 1.949936] mt7621-pci 1e140000.pcie: | ||
| + | [ 1.968667] mt7621-pci 1e140000.pcie: | ||
| + | [ 1.981341] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff] | ||
| + | [ 1.995051] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] | ||
| + | [ 2.008749] pci_bus 0000:00: root bus resource [bus 00-ff] | ||
| + | [ 2.019677] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] (bus address [0x00000000-0x0fffffff]) | ||
| + | [ 2.039991] pci 0000: | ||
| + | [ 2.051976] pci 0000: | ||
| + | [ 2.064478] pci 0000: | ||
| + | [ 2.077024] pci 0000: | ||
| + | [ 2.085019] pci 0000: | ||
| + | [ 2.098149] pci 0000: | ||
| + | [ 2.110179] pci 0000: | ||
| + | [ 2.124240] pci 0000: | ||
| + | [ 2.136901] pci 0000: | ||
| + | [ 2.167861] pci 0000: | ||
| + | [ 2.178292] pci 0000: | ||
| + | [ 2.190442] pci 0000: | ||
| + | [ 2.203976] pci 0000: | ||
| + | [ 2.218363] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 | ||
| + | [ 2.231590] pci 0000: | ||
| + | [ 2.244779] pci 0000: | ||
| + | [ 2.258646] pci 0000: | ||
| + | [ 2.272171] pci 0000: | ||
| + | [ 2.286563] pci 0000: | ||
| + | [ 2.300089] pci 0000: | ||
| + | [ 2.313628] pci 0000: | ||
| + | [ 2.328202] pci 0000: | ||
| + | [ 2.338092] pci 0000: | ||
| + | [ 2.351614] pci 0000: | ||
| + | [ 2.365140] pci 0000: | ||
| + | [ 2.380951] ubi0: attaching mtd5 | ||
| + | [ 2.393603] mt7530 mdio-bus: | ||
| + | [ 2.433220] ubi0: scanning is finished | ||
| + | [ 2.453234] ubi0: attached mtd5 (name " | ||
| + | [ 2.464596] ubi0: PEB size: 65536 bytes (64 KiB), LEB size: 65408 bytes | ||
| + | [ 2.477780] ubi0: min./max. I/O unit sizes: 1/256, sub-page size 1 | ||
| + | [ 2.490082] ubi0: VID header offset: 64 (aligned 64), data offset: 128 | ||
| + | [ 2.503076] ubi0: good PEBs: 434, bad PEBs: 0, corrupted PEBs: 0 | ||
| + | [ 2.515036] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 | ||
| + | [ 2.529420] ubi0: max/mean erase counter: 9/5, WL threshold: 4096, image sequence number: 1657914794 | ||
| + | [ 2.547599] ubi0: available PEBs: 0, total reserved PEBs: 434, PEBs reserved for bad PEB handling: 0 | ||
| + | [ 2.565816] ubi0: background thread " | ||
| + | [ 2.565936] UBI: block: volume size is not a multiple of 512, last 256 bytes are ignored! | ||
| + | [ 2.595279] block ubiblock0_0: | ||
| + | [ 2.614412] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. | ||
| + | [ 2.632831] Freeing unused kernel memory: 1292K | ||
| + | [ 2.641888] This architecture does not have kernel memory protection. | ||
| + | [ 2.654743] Run /sbin/init as init process | ||
| + | [ 3.204027] init: Console is alive | ||
| + | [ 3.211196] init: - watchdog - | ||
| + | [ 4.225372] kmodloader: loading kernel modules from / | ||
| + | [ 4.347999] usbcore: registered new interface driver usbfs | ||
| + | [ 4.359202] usbcore: registered new interface driver hub | ||
| + | [ 4.369958] usbcore: registered new device driver usb | ||
| + | [ 4.389472] SCSI subsystem initialized | ||
| + | [ 4.427621] kmodloader: done loading kernel modules from / | ||
| + | [ 4.453721] init: - preinit - | ||
| + | [ 5.273772] random: jshn: uninitialized urandom read (4 bytes read) | ||
| + | [ 5.360807] random: jshn: uninitialized urandom read (4 bytes read) | ||
| + | [ 5.474410] random: jshn: uninitialized urandom read (4 bytes read) | ||
| + | [ 6.144296] mtk_soc_eth 1e100000.ethernet swp0: PHY [mdio-bus: | ||
| + | [ 6.166211] mtk_soc_eth 1e100000.ethernet swp0: configuring for phy/rgmii link mode | ||
| + | Press the [f] key and hit [enter] to enter failsafe mode | ||
| + | Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level | ||
| + | [ 8.441218] UBIFS (ubi0:1): Mounting in unauthenticated mode | ||
| + | [ 8.452838] UBIFS (ubi0:1): background thread " | ||
| + | [ 8.485258] UBIFS (ubi0:1): recovery needed | ||
| + | [ 8.753298] random: crng init done | ||
| + | [ 8.760079] random: 7 urandom warning(s) missed due to ratelimiting | ||
| + | [ 9.206221] UBIFS (ubi0:1): recovery completed | ||
| + | [ 9.215286] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name " | ||
| + | [ 9.230902] UBIFS (ubi0:1): LEB size: 65408 bytes (63 KiB), min./max. I/O unit sizes: 8 bytes/256 bytes | ||
| + | [ 9.249636] UBIFS (ubi0:1): FS size: 21846272 bytes (20 MiB, 334 LEBs), journal size 1111936 bytes (1 MiB, 17 LEBs) | ||
| + | [ 9.270493] UBIFS (ubi0:1): reserved for root: 1031852 bytes (1007 KiB) | ||
| + | [ 9.283722] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 907AC48D-B261-4D78-B446-E51308CA2E7C, | ||
| + | [ 9.471484] mount_root: overlay filesystem has not been fully initialized yet | ||
| + | [ 9.487468] mount_root: switching to ubifs overlay | ||
| + | [ 9.516608] urandom-seed: | ||
| + | [ 9.638014] procd: - early - | ||
| + | [ 9.644115] procd: - watchdog - | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | Please press Enter to activate this console. | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | [ | ||
| + | </ | ||
| </ | </ | ||
| Line 1086: | Line 1526: | ||
| ===== Tags ===== | ===== Tags ===== | ||
| [[meta: | [[meta: | ||
| - | {{tag> | ||