Arcadyan / Astoria prv3399B-E-LT (aka Livebox Plus)

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

ISP Orange Spain is installing this router from 2018 onwards. I has dual wifi, 4x Gb switch, 2x phone lines and 1x USB support. It runs a SoC Broadcom 68380.

Not supported.

CPU Ram Flash Network WLAN USB Serial JTag
BCM68380 @ 600 MHz 256 MiB 128 MiB 4x 10/100/1000 bgn & ac 1x 2.0 Yes Unpopulated?
Architecture MIPS
Vendor Broadcom
Bootloader CFE customized by Arcadyan
System-On-Chip BCM68380 - MIPS 24K V4.12
CPU/Speed 600 MHz
Flash-Chip Toshiba/Kioxia TC58BVG0S3HTA00
Winbond W25x05CLSNFG
Flash size 128 MiB (NAND)
64 KiB (NOR)
RAM 256 MiB
Wireless BCM4321 2.4GHz 802.11bgn & Quantenna QT3740BC
Ethernet 10/100/1000 Mbit/s w/ vlan support
Switch ?
USB 1x 2.0
Serial Yes
JTAG No Not populated

You will need a phillips screwdriver.

  1. Remove 4x screws at the bottom of the device
  2. Detach from rear to front, the upper case from the bottom case

port.serial general information about the serial port, serial port cable, etc.

WARNING This device has 2 sets of UART, one dedicated to the early boot i.e. bootloader, and the second for the operating system (OS) itself e.g. linux.

The Tx pin for the OS, needed in order to reach Busybox, hasn't been discovered. It might be hard cancelled via resistor or soft cancelled via boot parameter.

See photo below for the pinout of the Serial Port of this specific device:

You will need some soldering skills though to really have access to it.

Serial connection parameters
for Arcadyan / Astoria prv3399B-E-LT
115200, 8N1

port.jtag general information about the JTAG port, JTAG cable, etc.

This is not confirmed but there're several unpopulated pins on the board. Some of them are known to be UART, it might be well that the rest of them are for JTAG:

Soft hacks

Access to web CFE

First, you will need to gain access to the bootloader CFE and stop the countdown.

Once there, use your browser to reach:

192.168.1.1

A fancy menu will pop-up as below:

Enable CFE countdown
  1. First you need to have access to the CFE. You might need this hack
  2. Now enter command “c”
  3. Select “Boot Image” 2
  4. Leave the rest of parameters untouched by pressing “intro”

Hard hacks

During boot, specific NAND flash pins can be shorcircuited in order to provoke a boot fail and therefore access to bootloader.

WARNING: This method is considered to be safe but use at your own discretion.
Access to CFE menu

This hack will need some training and skill. Don't give up! Basically, we will let the system jump to CFE bootloader and corrupt the loading of any further image from NAND flash.

  1. Switch on the device
  2. Let system jump to the “Copyright” line
  3. Now shortcircuit pins 8&9. See diagram at the bottom. Use the tip of a needle, thin screwdriver, etc
  4. After success, error messages will pop up and you will have access to the CFE command line as follows

---- HELO ZBSS RAMI Copyright (C) 2019 Arcadyan Technology. NANDFLASH: DEVICE ID: 0x98f18015f2, size: 131072KB, type: SLC block: 128KB(1024), page: 2KB, oob: 64Bytes nandflash_bbt_scan_block: detect bad block marker @ 0x6000000 NVRAM(0) MAGIC checking passed! NVRAM(0) CRC checking passed! total 10 of NVRAM(0) entries loaded NVRAM(1) MAGIC checking passed! NVRAM(1) CRC checking passed! total 10 of NVRAM(1) entries loaded BOOTLOADER version 1.2.4 for PRV3397B_E_LT Build Date: Tue Apr 25 13:45:35 2017 (tinghung_chen@buildbed) Chip ID: BCM68380B0 MIPS: 600MHz, DDR: 533MHz, Bus: 240MHz, RDP: 800MHz Memory Test Passed! Total Memory: 268435456 bytes (256MB) *** Press any key to stop auto run (0 seconds) *** Auto run second count down: 0 Loading secondary image ... ERROR: data is invalid and not correctable at offset 0x2b00000 Could not read from flash: CFE error -4 enable IH Wan-Wan forwarding... data_path_go Done!! Set EMAC4 as RGMII Creating CPU ring for queue number 0 with 32 packets descriptor=0x8b58cb60 Done initializing Ring 0 Base=0xad0141e0K End=0xad0143e0K calculated entries= 32 RDD Base=0x0d0141e0K descriptor=0x8b58cb60 Open PHY 1 on MAC 0 : link state = Down Open PHY 2 on MAC 1 : link state = Down Open PHY 3 on MAC 2 : link state = Down Open PHY 4 on MAC 3 : link state = Down Open PHY 0 on MAC 4 : link state = Down web info: Waiting for connection on socket 0. PRV3397B_E_LT>


Congratulations! Now you can consider enabling the bootloader countdown and therefore have CFE always reachable. See this

Using the CFE hack above, now you can enter the menu of the bootloader:

This is a piece of obscured software; seems an Arcadyan customized version of the CFE with little options.

RV3397B_E_LT>  help
Available commands:

sc                  Update certificate
show devices        Display information about the installed devices.
erasepart           Erase the specified partition
m                   Change the board's manufacture setting
c                   Change the board's setting
uc                  Update certificate file
u                   Update 1st/2nd flash image or bootloader
br                  Boot program from 1st/2nd cferam2
r                   Reset the board
help                Obtain help for CFE commands

As reported by bootloader:

PRV3397B_E_LT>show devices
Device Name          Description
-------------------  ---------------------------------------------------------
uart0                BCM63xx DUART channel 0
nandflash0.bootldr   offset 00000000 size 512KB
nandflash0.ca        offset 00080000 size 512KB
nandflash0.manufac   offset 00100000 size 512KB
nandflash0.nvram     offset 00180000 size 512KB
nandflash0.pri_boot  offset 00200000 size 512KB
nandflash0.pri_linu  offset 00280000 size 5120KB
nandflash0.pri_root  offset 00780000 size 35840KB
nandflash0.sec_boot  offset 02A80000 size 512KB
nandflash0.sec_linu  offset 02B00000 size 5120KB
nandflash0.sec_root  offset 03000000 size 35840KB
nandflash0.pri_cfg   offset 05300000 size 512KB
nandflash0.sec_cfg   offset 05380000 size 512KB
nandflash0.softrip   offset 05400000 size 512KB
nandflash0.softuser  offset 05480000 size 512KB
nandflash0.ubifs     offset 05500000 size 43008KB
nandflash0.oops_dat  offset 07F00000 size 1024KB
eth0
                     YàYYYE$
                            Yø
*** command status = 0
PRV3397B_E_LT>

This info is taken from the early UART.

---- BTL1 HELO CPUI L1CI CPUI L1CI ZBSS CODE DATA L12F MAIN OTP? OTPP ROTB SCBT NAND IMG? IMGL HDR? HDRP MCV? KEY? KEYA MID? MIDP MCVA SBI? SBIA PASS ---- HELO CPUI L1CI PLLI PMCB DRAM ---- PHYS ZQDN PHYE DINT TST1 TST2 PASS ---- ZBSS L12F ROMI PSRA PSRB PSRC PSRD PSRE ---- HELO ZBSS RAMI Copyright (C) 2017 Arcadyan Technology. NANDFLASH: DEVICE ID: 0x98f18015f2, size: 131072KB, type: SLC block: 128KB(1024), page: 2KB, oob: 64Bytes nandflash_bbt_scan_block: detect bad block marker @ 0x6000000 NVRAM(0) MAGIC checking passed! NVRAM(0) CRC checking passed! total 10 of NVRAM(0) entries loaded NVRAM(1) MAGIC checking passed! NVRAM(1) CRC checking passed! total 10 of NVRAM(1) entries loaded BOOTLOADER version 1.2.4 for PRV3397B_E_LT Build Date: Tue Apr 25 13:45:35 2017 (paul_shih@buildbox1) Chip ID: BCM68380B0 MIPS: 600MHz, DDR: 533MHz, Bus: 240MHz, RDP: 800MHz Memory Test Passed! Total Memory: 268435456 bytes (256MB) Board IP address 192.168.1.1 Board IP netmask 255.255.255.0 Gateway IP address 0.0.0.0 Server IP address 192.168.1.99 Boot image (1 or 2) 2 Temp boot (0, 1 or 2) 0 Boot countdown delay (0 to 3) 0 Serial number ARLT83733412 MAC address number 4 MAC address base 4C-1B-86-59-4E-56 Wireless SSID 4E56 Wireless key 2WU2pKex Wireless WPS pin 53478306 Admin password 2WU2pKex Hardware version R01 Manufacturing mode (0 or 1) 0 *** Press any key to stop auto run (0 seconds) *** Auto run second count down: 0 Loading secondary bootram ... Decryption OK! Decompression OK! Entry at 0x8b500000 Starting program at 0x8b500000 ---- HELO ZBSS RAMI Copyright (C) 2019 Arcadyan Technology. NANDFLASH: DEVICE ID: 0x98f18015f2, size: 131072KB, type: SLC block: 128KB(1024), page: 2KB, oob: 64Bytes nandflash_bbt_scan_block: detect bad block marker @ 0x6000000 NVRAM(0) MAGIC checking passed! NVRAM(0) CRC checking passed! total 10 of NVRAM(0) entries loaded NVRAM(1) MAGIC checking passed! NVRAM(1) CRC checking passed! total 10 of NVRAM(1) entries loaded BOOTLOADER version 1.2.4 for PRV3397B_E_LT Build Date: Tue Apr 25 13:45:35 2017 (tinghung_chen@buildbed) Chip ID: BCM68380B0 MIPS: 600MHz, DDR: 533MHz, Bus: 240MHz, RDP: 800MHz Memory Test Passed! Total Memory: 268435456 bytes (256MB) *** Press any key to stop auto run (0 seconds) *** Auto run second count down: 0 Loading secondary image ... Finished loading 5242880 bytes DATE : Fri Oct 25 18:13:05 2019 VER : v1.03.05.217 CRC : 3C183963 CRC OK! Signature OK! Decryption OK! Decompression OK! Code Address: 0x80010000, Entry Address: 0x80451a20 Starting program at 0x80451a20


This info is taken from the OS UART.

Quantenna Mini U-Boot Version: v37.4.0.28 Built: Oct 26 2015 at 19:23:50 br 1G-FD Using br device TFTP from server 1.1.1.1; our IP address is 1.1.1.2 Filename 'u-boot.bin'. Load address: 0x88000000 Loading: T ############## done Bytes transferred = 69872 (0x110f0) Boot reached stage 13 Boot reached stage 12 Valid CRC found in flash restoring env... Boot reached stage 11 hw_config_id 65535: 'QTM840_5S3_MAC' Cold boot Reset status: 0x00000001 Info: data uncached: addr=0xc0000000 size=1024MB Info: text at 0x88040000, stack at 0x88013ffc(8192), heap at 0x88000000(73728), uboot size 173708 Info: i-cache is enabled Info: d-cache is enabled Info: CPU freq is 500000000, dev freq is 125000000 Info: Quantenna U-Boot version:v37.4.0.136 Info: build date 'May 10 2019', time '23:46:47' SPI flash info: name : w25x05 jedec_id : 0xef3010 sector size : 4096 number of sector : 16 frequency : 104000000 flags : 0x2 lock : DDR_INIT: type = 16, speed = 2, size = 134217728, rev = 0x43, param = 0x0 DDR_INIT: replacing invalid param = 0x0 with default 0xe7b 500MHz BDA at 0x80002000 In: serial Out: serial Err: serial Boot reached stage 64 Boot reached stage 65 br Hit any key to stop autoboot: 0 Boot reached stage 80 1G-FD Using br device TFTP from server 1.1.1.1; our IP address is 1.1.1.2 Filename 'topaz-linux.lzma.img'. Load address: 0x83000000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################## done Bytes transferred = 5831576 (0x58fb98) Boot reached stage 81 Boot reached stage 84 Boot reached stage 1 ## Booting kernel from Legacy Image at 83000000 ... Boot reached stage 2 Boot reached stage 3 Image Name: topaz-linux Image Type: arc Linux Kernel Image (lzma compressed) Data Size: 5823384 Bytes = 5.6 MB Load Address: 8493a000 Entry Point: 8493a000 Qtn flags: 00000001 Verifying Checksum ... OK Boot reached stage 4 Boot reached stage 5 Boot reached stage 6 Boot reached stage 14 Uncompressing Kernel Image ... OK Boot reached stage 7 Boot reached stage 8 Command line TAG setup Params->u.cmdline.cmdline console=ttyS0,115200n8 earlyprintk=1 hw_config_id=65535 p console=ttyS0,115200n8 earlyprintk=1 hw_config_id=65535 ## Unset TAG qtn_flags 1 ## Transferring control to Linux (at address 8493a000) ATAG parameters 88067d94 - 88067dec... [ 0.000000] Linux version 2.6.35.12 (tinghung_chen@buildbed) (gcc version 4.2.1 (ARC_2.3)) #2 Tue May 28 16:51:36 CST 2019 [ 0.000000] Parsing ATAG parameters from bootloader [ 0.000000] ATAG_CORE: successful parsing [ 0.000000] ATAG_CMDLINE: command line = console=ttyS0,115200n8 earlyprintk=1 hw_config_id=65535 [ 0.000000] Board id: 65535 [ 0.000000] ATAG_HW_CONFIG_ID: hw_config_id = 65535 [ 0.000000] [ 0.000000] Processor Family: ARC 700 [0x33] [ 0.000000] CPU speed : 500.00 Mhz [ 0.000000] Timers: TIMER1 TIMER0 [ 0.000000] Interrupt Vect Base: 0x88052400 [ 0.000000] Peripheral Base: NOT present; assuming 0xCOFC0000 [ 0.000000] Data UNCACHED Base (I/O): start 0xc0 Sz, 1024 MB [ 0.000000] ARC700 MMU Ver [2] [ 0.000000] PAGE SIZE 8k [ 0.000000] JTLB 128 x 2 = 256 entries [ 0.000000] uDTLB 8 entr, uITLB 4 entr [ 0.000000] TLB Refill "will NOT" Flush uTLBs [ 0.000000] Detected I-cache : [ 0.000000] Type=2 way set-assoc, Line length=32, Size=16K (enabled) [ 0.000000] Detected D-cache : [ 0.000000] Type=4 way set-assoc, Line length=32, Size=16K (enabled) [ 0.000000] Extensions: [ 0.000000] MPY: 32x32 with ANY Result Reg MAC MPY: Dual 16 x 16 and 32 x 16 [ 0.000000] DCCM: N/A ICCM: N/A [ 0.000000] CRC: N/A, SWAP: Present NORM: Present [ 0.000000] Min-Max: Present, Barrel Shifter: Present [ 0.000000] Ext Arith Insn: Present [ 0.000000] Floating Point Extension: N/A [ 0.000000] On node 0 totalpages: 16383 [ 0.000000] free_area_init_node: node 0, pgdat 85b55dac, node_mem_map 85c06024 [ 0.000000] Normal zone: 72 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16311 pages, LIFO batch:3 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16311 [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlyprintk=1 hw_config_id=65535 [ 0.000000] bootconsole [ruby_early0] enabled [ 0.000000] PID hash table entries: 512 (order: -2, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 3, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 2, 32768 bytes) [ 0.000000] Memory: 36088KB available (2165K code,1202K data, 15872K init) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU debugfs-based tracing is enabled. [ 0.000000] Verbose stalled-CPUs detection is disabled. [ 0.000000] clockevent mode switch to [1] [ 0.000000] clockevent mode switch to [2] [ 0.000000] Calibrating delay loop... 249.03 BogoMIPS (lpj=622592) [ 0.115000] pid_max: default: 4096 minimum: 301 [ 0.120000] Mount-cache hash table entries: 1024 [ 0.125000] Starting run_ksoftirqd, stack (thread_info) at 85b7a000 cpu 0 [ 0.130000] NET: Registered protocol family 16 [ 0.135000] Topaz heap 1 in SRAM 88016360<->88020000 [ 0.140000] Topaz heap 2 in SRAM 88011000<->88012000 [ 0.150000] bio: create slab <bio-0> at 0 [ 0.160000] watch64: 2003/08/22 Josef 'Jeff' Sipek <jeffpc@xxxxxxxxxxxxx> [ 0.165000] watch64: Enabling Watch64 extensions...done. [ 0.170000] Switching to clocksource ARC Timer1 [ 0.175000] NET: Registered protocol family 2 [ 0.180000] IP route cache hash table entries: 2048 (order: 0, 8192 bytes) [ 0.185000] TCP established hash table entries: 4096 (order: 2, 32768 bytes) [ 0.195000] TCP bind hash table entries: 4096 (order: 1, 16384 bytes) [ 0.200000] TCP: Hash tables configured (established 4096 bind 4096) [ 0.205000] TCP reno registered [ 0.210000] NET: Registered protocol family 1 [ 0.815000] JFFS2 version 2.2. (NAND) c 2001-2006 Red Hat, Inc. [ 0.820000] msgmni has been set to 70 [ 0.825000] io scheduler noop registered (default) [ 1.250000] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled [ 1.255000] serial8250.0: ttyS0 at MMIO 0xf0000000 (irq = 48) is a 16550A [ 1.260000] console [ttyS0] enabled, bootconsole disabled [ 1.260000] console [ttyS0] enabled, bootconsole disabled [ 1.265000] brd: module loaded [ 1.275000] loop: module loaded [ 1.280000] spi_flash: Force not to support Protect Mode [ 1.285000] Creating 3 MTD partitions on "spi_flash": [ 1.290000] 0x000000000000-0x000000005000 : "uboot" [ 1.300000] 0x000000005000-0x00000000b000 : "uboot_env" [ 1.310000] 0x00000000b000-0x000000010000 : "data" [ 1.315000] spi_flash: SPI flash driver initialized successfully! [ 1.320000] ruby_health loading [ 1.325000] HBM pool: emac rx 0x0 to 0x8000, wmac rx 0x8000 to 0xa000 [ 1.720000] HBM meta: emac rx 0x63c040 to 0x6bc040, wmac rx 0x6bc080 to 0x6dc080 [ 1.725000] topaz_hbm_init_pool_list pool 0 pool_list 0x88000000 bus_range 0x16ec400 to 0x26ec400 sz 2048 count 8192 [ 1.725000] topaz_hbm_init_pool_list pool 1 pool_list 0x88008000 bus_range 0x26fc400 to 0x48fc400 sz 17408 count 2048 [ 1.725000] topaz_hbm_init_pool_list pool 3 pool_list 0x8800a000 bus_range 0x0 to 0x0 sz 0 count 4096 [ 1.730000] topaz_busmon_init success [ 1.735000] topaz_temp_sens_init success [ 1.740000] u32 classifier [ 1.740000] input device check on [ 1.745000] Actions configured [ 1.750000] Netfilter messages via NETLINK v0.30. [ 1.755000] nf_conntrack version 0.5.0 (563 buckets, 2252 max) [ 1.760000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 1.765000] TCP cubic registered [ 1.770000] NET: Registered protocol family 10 [ 1.775000] NET: Registered protocol family 17 [ 1.780000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> [ 1.785000] All bugs added by David S. Miller <davem@redhat.com> [ 1.795000] Freeing unused kernel memory: 15872k freed [8493a000] TO [858ba000] [ 1.800000] Common mmap addr-space starts 2c0f0000 init started: BusyBox v1.10.3 (2019-05-28 16:43:09 CST) starting pid 44, tty '': '/etc/init.d/rcS' [ 2.180000] load_module: 'bootcfg' using DRAM (offset:0x85800000, size:0x96b0) Starting portmap: done Initializing random number generator... done. /mnt/jffs2/wireless_conf.txt not found. Creating a default conf file restore_wireless_conf restore_wireless_conf: wifi_mode = default restore_wireless_conf: Setting default wireless config params restore_wireless_conf: board_id = 65535 restore_wireless_conf: board_name = QTM840_5S3_MAC restore_wireless_conf: Writing config params to /mnt/jffs2/wireless_conf.txt Starting network... [ 3.500000] load_module: 'rtl8367b' using DRAM (offset:0x86700000, size:0x32a77) [ 3.505000] rtl8367b: module license 'unspecified' taints kernel. [ 3.510000] Disabling lock debugging due to kernel taint [ 3.565000] load_module: 'emaclib' using DRAM (offset:0x85870000, size:0x53c1) [ 3.685000] load_module: 'switch_vlan' using DRAM (offset:0x85858000, size:0x2739), SRAM (offset:0x88016368, size:0x1) [ 3.790000] load_module: 'switch_tqe' using DRAM (offset:0x85850000, size:0x3b3a), SRAM (offset:0x88016378, size:0x1a10) [ 3.840000] tqe_descs_alloc: 2048 tqe_rx_descriptors at kern uncached 0x580e1da0 bus 0x80017da0 [ 3.920000] load_module: 'fwt_if' using DRAM (offset:0x85898000, size:0x1af7) [ 3.955000] load_module: 'fwt_ctrl' using DRAM (offset:0x86740000, size:0x23a01) [ 4.010000] load_module: 'dpi' using DRAM (offset:0x85892000, size:0x1d9f) [ 4.045000] load_module: 'switch_emac' using DRAM (offset:0x85cec000, size:0x2563), SRAM (offset:0x88011a40, size:0x2f8) [ 4.110000] emac wbsp: 0 [ 4.115000] enable A2 (single) [ 4.175000] Random stuff 2D emac0 is eth1_0, emac1 is unused Stateless mode. Using temporary ip address: Using IP address 1.1.1.2 Netmask is not set [ 4.445000] emac_lib eth1_0: force link (1000/Full) [ 4.565000] device eth1_0 entered promiscuous mode [ 4.570000] br0: port 1(eth1_0) entering forwarding state [ 4.575000] br0: port 1(eth1_0) entering forwarding state [ 4.605000] FWT: [00:aa:bb:cc:dd:02] add entry, port:emac0 node:0 index:876 4addr:0 entries:1 /sbin/ifup -a ifconfig: SIOCGIFFLAGS: No such device Version of /proc/bootcfg/qtn_regulatory_db.bin is Regulatory db version: v37.3.0.21 Version of /etc/qtn_regulatory_db.bin is Regulatory db version: v37.4.0.171 Selected database version: Regulatory db version: v37.4.0.171 Using /etc/qtn_regulatory_db.bin Starting qevt_server Starting inetd ... /scripts/cmdloop starting /sbin/qevt_server, at 00:00:05 up 0 min, load average: 0.08, 0.01, 0.00 [ 5.880000] load_module: 'hw_rev' using DRAM (offset:0x85834000, size:0x374c) Starting wireless... restore_default_config -nr restore_wireless_conf ap restore_wireless_conf: wifi_mode = ap restore_wireless_conf: Setting default wireless config params restore_wireless_conf: board_id = 65535 restore_wireless_conf: board_name = QTM840_5S3_MAC restore_wireless_conf: Writing config params to /mnt/jffs2/wireless_conf.txt restore_default_config: Updating security config files for mode ap restore_default_config: Removing block ACK restrictions restore_default_config: Configuration has been set to default values. Reboot after customizing to ensure correct operation. complete /scripts/cmdloop starting /sbin/qcsapi_rpcd, at 00:00:07 up 0 min, load average: 0.08, 0.01, 0.00 /scripts/cmdloop starting /sbin/call_qcsapi_rpcd, at 00:00:07 up 0 min, load average: 0.08, 0.01, 0.00 'monitor_temperature' is not enabled/set MAUI service started /etc/init.d/S91dhclient: line 26: syntax error: "else" unexpected /scripts/cmdloop starting /sbin/qharvestd, at 00:00:10 up 0 min, load average: 0.47, 0.09, 0.03 Starting httpd cp: cannot stat '/etc/minihttpd.conf': No such file or directory qharvestd[notice]: qharvestd v1.32.2 started starting pid 691, tty '/dev/console': '/bin/sh -l' BusyBox v1.10.3 (2019-05-28 16:43:09 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. quantenna # qharvestd[error]: qcsapi[interface_get_mac_addr] failed, err code = -19 (No such device) /scripts/readmem: line 10: cannot create /proc/wlanmem: nonexistent directory cat: can't open '/proc/wlanmem': No such file or directory qharvestd[error]: qcsapi[get_carrier_id] failed, err code = -19 (No such device) qharvestd[error]: failed to get device MAC address qharvestd[notice]: qharvest terminated Using IP address 1.1.1.2 Netmask is not set ifconfig: bad address '' Loading modules [ 13.550000] load_module: 'qtn_debug' using DRAM (offset:0x85838800, size:0x377) [ 13.670000] load_module: 'i2cbus' using DRAM (offset:0x85856000, size:0x1ce2) [ 13.825000] load_module: 'qtsens' using DRAM (offset:0x850d6000, size:0x7b6) [ 13.955000] load_module: 'pm_interval' using DRAM (offset:0x84960000, size:0x13b2) [ 14.140000] load_module: 'wlan' using DRAM (offset:0x84a00000, size:0xb9100) [ 14.485000] wlan: 0.8.4.2 (0.9.3.3) [ 14.650000] load_module: 'auc_fw' using DRAM (offset:0x866ec000, size:0x8cb) [ 14.755000] load_module: 'qvspmod' using DRAM (offset:0x84eb0000, size:0x3f39) [ 14.785000] QVSP module init [ 14.860000] load_module: 'qdrv' using DRAM (offset:0x84c00000, size:0xa9a40) [ 15.170000] qdrv wbsp: 0 [ 15.315000] load_module: 'wlan_xauth' using DRAM (offset:0x84eb9000, size:0x32f) [ 15.330000] br0: no IPv6 routers present [ 15.485000] load_module: 'wlan_ccmp' using DRAM (offset:0x84962000, size:0x1782) [ 15.660000] load_module: 'wlan_tkip' using DRAM (offset:0x85860000, size:0x2636) Loading MuC driver (qtn_driver.qtn_ruby.0.bin) no keyfile specified unable to load Public Key Waiting for Wireless Events from interfaces... Found power table in /etc/power_tables [ 16.985000] set power_selection 2 [ 16.990000] qdrv_soc_publish_params: parames->tqe_sem_en 0, auc_tqe_sem_en 0 [ 17.000000] ..... Current RFIC Chip ID -- 4 [ 17.295000] AuC SRAM start 0x88040000 end 0x88080000 size 262144 [ 17.300000] AuC is configured for non-MU SRAM layout [ 17.305000] AuC SRAM bank 0 start 0x88040000 end 0x88050000 [ 17.310000] AuC SRAM bank 1 start 0x88050000 end 0x88060000 [ 17.315000] AuC SRAM bank 2 start 0x88060000 end 0x88070000 [ 17.320000] AuC SRAM bank 3 start 0x88070000 end 0x88080000 [ 17.350000] MuC: g_tqe_sem_en 0 [ 17.350000] MuC: build date Wed, 03 Oct 2018 14:35:42 -0700 [ 17.355000] MuC: slow heap begin=0x002a33e0 end=0x004203e0 [ 17.360000] MuC: fast heap begin=0x80030800 end=0x80037000 [ 17.365000] MuC: stack start=0x8003ef80 sp=0x8003f6d4 [ 17.370000] MuC: calstate is 3 (prod), dcache on [ 17.375000] MuC: RFIC version 1 rev 0 [ 17.405000] qdrv_mac_reserve_clear: mac reservation table cleared [ 17.430000] QDRV: I2C dapter not found [ 17.445000] MuC: bb_init: FEM 0x7 bw_mode 0 chan 0 11b 0 11a 1 [ 17.450000] MuC: set max/nrm gain(0x27) done. [ 17.455000] MuC: set cca threshold! [ 17.455000] MuC: rf_optimizing_rf_register_map, set rf to 0x75 [ 17.460000] MuC: os_uc, after bb_rf_complete_attach. [ 17.465000] MuC: WMAC0: hal fd start=0xe5040300 count=48 size=108 end=0xe5041740 [ 17.470000] MuC: WMAC1: hal fd start=0xe5140d50 count=8 size=84 end=0xe5140ff0 [ 17.475000] MuC: freq 1 proj 1 [ 17.475000] MuC: dynamic one-bit autocorrelation enabled [ 17.480000] MuC: QMAT SRAM base 0x80070000 [ 17.485000] MuC: enable IRQs [ 17.610000] qdrv_mu_stat_init [ 17.685000] MuC: AuC enabled 0xe5101cd0/0x60063630 il 0xe5101284/0xe5101288 stats 0x60061170/0x600633700x6007e140 [ 17.690000] MuC: Update MU debug flag failed. keep old value : 0x00000000 [ 17.695000] QDRV: hardware is 4x4 11ac FO RGMII/PCIe QV840 [ 17.700000] MuC boot succeeded 0.085 seconds start-vap ap [ 19.280000] load_module: 'wlan_scan_ap' using DRAM (offset:0x85f20000, size:0x3176) [ 19.360000] QTM daemon registered [ 19.480000] qvsp_nl_node_init: QVSP not initialized [ 19.485000] MuC: qtn_mu_ndpa_setup: bw_cap 2 done [ 19.500000] VAP create succeeded 0.010 seconds [ 19.510000] MuC: qtn_mu_ndpa_setup: bw_cap 2 done [ 19.995000] MuC: calibration ver 0x801 bss_tm set to 1 neigh_repo reset to 0 radar in 80MHZ mode Setting mode to 11ac80 set_region: Setting regulatory region dev_name=wifi0 region=es mode=ap repeater=0 radar start with[ 21.865000] DFS_s_radio: parameters updated, region: eu regulatory eu [ 21.870000] MuC: macfw: radar_start......... [ 21.875000] MuC: radar_start, region eu = 2 [ 22.120000] qdrv_radar_enable_action: ERROR - radar already enabled ICAC: max_boot_cac is greater than 0, hence the parameter non_dfs_channel is ignored. To avoid doing initial CAC set max_boot_cac to 0. dfs_s_radio 1 dfs 0 non-dfs 0 scan 0 auto-channel channel 0 Configure max_boot_cac to 70 [ 23.005000] device wifi0 entered promiscuous mode [ 23.125000] Enabling SSDP flooding Beamforming enabled [ 24.175000] Enabling SCS SCS enabled QTM: load profile off QTM enabled: 0 [ 25.375000] MuC: Beacon scheme updated to 1 [ 25.420000] Starting DFS seamless radio... [ 25.435000] BRIDGE WLAN report flood-forwarding enabled QCS API error 1010: Cannot contact security manager No core dump generated QCS API error 34: Parameter value out of range [ 27.280000] Build name: v37.4.0.180 [ 27.285000] Build revision: 86411 [ 27.290000] Build type: SDK [ 27.295000] Build timestamp: 1538603078 [ 27.300000] Platform ID: 432 [ 27.300000] Hardware ID: QV840 [ 27.305000] Hardware revision: bbic4_rev_a2 [ 27.310000] Band: 5GHz [ 27.315000] Kernel version: 2.6.35 [ 27.320000] Calibration version: disabled [ 27.325000] DC/IQ cal version: V8.1 [ 27.325000] Power cal version: V8.1 [ 27.330000] MuC firmware: qtn_driver.qtn_ruby.0.bin [ 27.335000] DSP firmware: rdsp_driver.0.bin [ 27.340000] AuC firmware: auc_driver.nomu.0.bin [ 27.345000] MAC address 0: 4c:1b:86:59:4e:59 [ 27.350000] MAC address 1: 00:00:00:00:00:00 [ 27.355000] Recommended U-Boot: v37.4.0.136 Carrier ID 0, uboot update flag 0 complete MU-MIMO is not supported on this device Starting qrpe daemon... qtna-rpe(7.0.10-7e833fa) started PTA request polarity set to 0 PTA grant polarity set to 0 PTA disabled /scripts/cmdloop starting /sbin/qharvestd, at 01:00:32 up 0 min, load average: 0.80, 0.20, 0.06 qharvestd[notice]: qharvestd v1.32.2 started radar start with regulatory eu [ 32.395000] qdrv_radar_is_rdetection_required: ERROR - channel not yet set [ 32.395000] qdrv_radar_enable_action: ERROR - radar already enabled qharvestd[notice]: Pktlogger support detected qharvestd[info]: rest for 120s (120s 0ms after adjustment) [ 32.830000] channel 52 is added into non-primary channel list [ 32.870000] channel 56 is added into non-primary channel list [ 32.910000] channel 60 is added into non-primary channel list [ 32.950000] channel 64 is added into non-primary channel list [ 32.950000] Warning: all the sub channels are not in primary channel list! [ 32.995000] channel 116 is added into non-primary channel list [ 33.035000] channel 120 is added into non-primary channel list [ 33.075000] channel 124 is added into non-primary channel list [ 33.115000] channel 128 is added into non-primary channel list [ 33.115000] Warning: all the sub channels are not in primary channel list! [ 33.160000] channel 132 is added into non-primary channel list [ 33.200000] channel 136 is added into non-primary channel list [ 33.240000] channel 140 is added into non-primary channel list [ 33.325000] Starting DFS seamless radio... [ 33.620000] MuC: #RX data path optimal flag 0 [ 33.625000] MuC: rx_post_init: free 0 rxq 9 9 394 descr 0x8000f000/6592 cache 0x8002aa00/13184 [ 33.625000] MuC: auto cs is enabled [ 33.660000] WPS: [ 110.560000] RADAR: CAC completed for channel 108 (5540 MHz) [ 117.810000] channel 52 is removed from non-primary channel list [ 117.855000] channel 56 is removed from non-primary channel list [ 117.900000] channel 60 is removed from non-primary channel list [ 117.945000] channel 64 is removed from non-primary channel list update_5g_channel: 108 [ 119.510000] FWT: [00:2a:bb:cc:dd:04] add entry, port:emac0 node:0 index:58 4addr:0 entries:2 [ 126.140000] VAP create succeeded 0.010 seconds [ 126.170000] device wifi1 entered promiscuous mode [ 135.350000] br0: port 3(wifi1) entering forwarding state [ 135.350000] br0: port 3(wifi1) entering forwarding state [ 137.970000] VAP create succeeded 0.010 seconds [ 138.000000] device wifi2 entered promiscuous mode [ 149.465000] VAP create succeeded 0.010 seconds [ 149.490000] device wifi3 entered promiscuous mode qharvestd[info]: start oauth processing at 153.436828331 qharvestd[info]: target: https://qharvest-prod.quantenna.com/api/auth/token qharvestd[info]: request: { "username": "1072|4c:1b:86:59:4e:59", "password": "0000", "grant_type": "password", "scope": "device" } qharvestd[error]: curl_easy_perform(): Couldn't resolve host 'qharvest-prod.quantenna.com' qharvestd[info]: finish oauth processing at 153.530159547 (in 93ms) qharvestd[info]: poll_request: exponential backoff scale is 3 qharvestd[info]: next poll_request will be in 10 seconds qharvestd[info]: rest for 10s (9s 907ms after adjustment) qharvestd[info]: start oauth processing at 163.451312751 qharvestd[info]: target: https://qharvest-prod.quantenna.com/api/auth/token qharvestd[info]: request: { "username": "1072|4c:1b:86:59:4e:59", "password": "0000", "grant_type": "password", "scope": "device" } qharvestd[error]: curl_easy_perform(): Couldn't resolve host 'qharvest-prod.quantenna.com' qharvestd[info]: finish oauth processing at 163.456939859 (in 5ms) qharvestd[info]: poll_request: exponential backoff scale is 4 qharvestd[info]: next poll_request will be in 24 seconds qharvestd[info]: rest for 24s (23s 995ms after adjustment) iwpriv wifi0 set_owl_beacon 1 iwpriv wifi0 set_coc_ndfs 0 update_24g_channel: 1 [ 182.285000] ARC_24G_CHAN_IN_5G=1 qharvestd[info]: start oauth processing at 187.465876831 qharvestd[info]: target: https://qharvest-prod.quantenna.com/api/auth/token qharvestd[info]: request: { "username": "1072|4c:1b:86:59:4e:59", "password": "0000", "grant_type": "password", "scope": "device" } qharvestd[error]: curl_easy_perform(): Couldn't resolve host 'qharvest-prod.quantenna.com' qharvestd[info]: finish oauth processing at 187.471585747 (in 5ms) qharvestd[info]: poll_request: exponential backoff scale is 5 qharvestd[info]: next poll_request will be in 33 seconds qharvestd[info]: rest for 33s (32s 995ms after adjustment) qharvestd[info]: start oauth processing at 220.480904255 qharvestd[info]: target: https://qharvest-prod.quantenna.com/api/auth/token qharvestd[info]: request: { "username": "1072|4c:1b:86:59:4e:59", "password": "0000", "grant_type": "password", "scope": "device" } qharvestd[error]: curl_easy_perform(): Couldn't resolve host 'qharvest-prod.quantenna.com' qharvestd[info]: finish oauth processing at 220.486698935 (in 5ms) qharvestd[info]: poll_request: exponential backoff scale is 6 qharvestd[info]: next poll_request will be in 93 seconds qharvestd[info]: rest for 93s (92s 995ms after adjustment) qharvestd[info]: start oauth processing at 313.496165543 qharvestd[info]: target: https://qharvest-prod.quantenna.com/api/auth/token qharvestd[info]: request: { "username": "1072|4c:1b:86:59:4e:59", "password": "0000", "grant_type": "password", "scope": "device" } qharvestd[error]: curl_easy_perform(): Couldn't resolve host 'qharvest-prod.quantenna.com'


COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2022/10/28 08:50
  • by danitool