Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
Next revisionBoth sides next revision
inbox:toh:arcadyan:astoria:prv3399b-e-lt [2021/09/27 10:17] – Created from the form at meta:create_new_device_page mandrake-leeinbox:toh:arcadyan:astoria:prv3399b-e-lt [2021/10/17 08:25] – [Info] mandrake-lee
Line 1: Line 1:
-====== Arcadyan / Astoria prv3399B-E-LT ======+====== Arcadyan / Astoria prv3399B-E-LT (aka Livebox Plus) ======
 ~~NOTOC~~ ~~NOTOC~~
  
Line 6: Line 6:
 {{page>meta:infobox:construction&noheader&nofooter&noeditbtn}} {{page>meta:infobox:construction&noheader&nofooter&noeditbtn}}
  
-//Write a short, relevant description of the device. Include a technical overview, but avoid marketing buzzwords/useless stuff. Two to four sentences is about rightA picture is goodtooEdit the page to see how to add pictures.//+ISP Orange Spain is installing this router from 2018 onwardsI has dual wifi4x Gb switch, 2x phone lines and 1x USB supportIt runs a SoC Broadcom 68380.
  
 /*****/ /*****/
 /* How to add images ========> https://openwrt.org/meta/adding_images_to_openwrt_wiki */ /* How to add images ========> https://openwrt.org/meta/adding_images_to_openwrt_wiki */
 /*****/ /*****/
- +{{ :media:arcadyan:prv3399b:prv3399b_main_view.jpg?direct&400 |}}
-{{ media:example:genericrouter1.png?200|Generic Router}}+
  
  
Line 43: Line 42:
 ===== Hardware highlights ===== ===== Hardware highlights =====
 ^ CPU                        ^ Ram      ^ Flash   ^ Network     ^ WLAN   ^ USB      ^ Serial   ^ JTag   ^ ^ CPU                        ^ Ram      ^ Flash   ^ Network     ^ WLAN   ^ USB      ^ Serial   ^ JTag   ^
-EXAMPLE RT3052 384 MHz   |  64 MiB  |  MiB  |  4x 10/100  |  bgn    1x 2.0  |   Yes    |   ?    |+BCM68380 600 MHz   |  256 MiB  |  128 MiB  |  4x 10/100/1000   bgn & ac   |  1x 2.0  |   Yes    |  Unpopulated?    |
  
  
Line 111: Line 110:
 ===== Hardware ===== ===== Hardware =====
 ==== Info ==== ==== Info ====
-^ Architecture     EXAMPLE MIPS                             +^ Architecture     [[wp>MIPS_architecture|MIPS ]]           
-^ Vendor           EXAMPLE Ralink                           +^ Vendor           [[https://www.broadcom.com/|Broadcom]]   
-^ Bootloader       EXAMPLE U-Boot                           +^ Bootloader       [[:docs:techref:bootloader:cfe|CFE]] customized by Arcadyan               
-^ System-On-Chip   EXAMPLE Ralink RT3052 - MIPS 24K V4.12   | +^ System-On-Chip   BCM68380 - MIPS 24K V4.12   | 
-^ CPU/Speed        | EXAMPLE 451 MHz                          | +^ CPU/Speed        | 600 MHz                          | 
-^ Flash-Chip       EXAMPLE unkown                           +^ Flash-Chip       Toshiba/Kioxia [[https://business.kioxia.com/info/docget.jsp?did=14875&prodName=TC58BVG0S3HTA00|TC58BVG033HTA00]] \\ Winbond [[https://www.winbond.com/resource-files/W25X05CL_G%2008012019.pdf|W25x05CLSNFG]]                 
-^ Flash size       EXAMPLE 8 MiB                            +^ Flash size       128 MiB (NAND) \\ 512 KiB (NOR)                       
-^ RAM              | EXAMPLE 64 MiB                           | +^ RAM              | 256 MiB                           | 
-^ Wireless         EXAMPLE RT2860v2 2.4GHz 802.11bgn        +^ Wireless         BCM4321 2.4GHz 802.11bgn & Quantenna QT3740BC  
-^ Ethernet         EXAMPLE 10/100 Mbit/s w/ vlan support    | +^ Ethernet         | 10/100/1000 Mbit/s w/ vlan support    | 
-^ Switch           EXAMPLE Qualcomm Atheros QCA8337         +^ Switch           ?        
-^ USB              | EXAMPLE 1x 2.0                           | +^ USB              | 1x 2.0                           | 
-^ Serial           EXAMPLE [[#Serial|Yes]]                  | +^ Serial           | [[#Serial|Yes]]                  | 
-^ JTAG             EXAMPLE [[#JTAG|Not populated]]          |+^ JTAG             Unknown [[#JTAG|Not populated]]          |
  
  
Line 142: Line 141:
 /* e.g. {{:media:yourbrand:yourbrand_yourmodel_front.jpg?400|}}                                  */ /* e.g. {{:media:yourbrand:yourbrand_yourmodel_front.jpg?400|}}                                  */
 /* Thanks, your wiki administration - Oct. 2015 */ /* Thanks, your wiki administration - Oct. 2015 */
 +{{ :media:arcadyan:prv3399b:prv3399b_front_case.jpg?direct&400 |}}
  
-**Insert photo of front of the casing**+{{ :media:arcadyan:prv3399b:prv3399b_rear_case.jpg?direct&400 |}}
  
-**Insert photo of back of the casing**+{{ :media:arcadyan:prv3399b:prv3399b_back_case.jpg?direct&400 |}}
  
-**Insert photo of backside label**+{{ :media:arcadyan:prv3399b:prv3399b_board_top.jpg?direct&400 |}} 
 + 
 +{{ :media:arcadyan:prv3399b:prv3399b_board_back.jpg?direct&400 |}}
  
-**Insert photo of PCB** 
  
 ==== Opening the case ==== ==== Opening the case ====
  
-<WRAP BOX> +You will need a phillips screwdriver. 
-FIXME //Describe what needs to be done to open the device, e.g. remove rubber feet, adhesive labels, screws, ...// +  - Remove 4x screws at the bottom of the device 
-</WRAP>+  - Detach from rear to frontthe upper case from the bottom case
  
 ==== Serial ==== ==== Serial ====
 -> [[docs:techref:hardware:port.serial]] general information about the serial port, serial port cable, etc. -> [[docs:techref:hardware:port.serial]] general information about the serial port, serial port cable, etc.
  
-How to connect to the Serial Port of this specific device:\\ +**WARNING** This device has 2 sets of UART, one dedicated to the early boot i.e. bootloader, and the second for the operating system (OS) itself e.g. linux.
-**Insert photo of PCB with markings for serial port**+
  
-<WRAP BOX> +The Tx pin for the OS, needed in order to reach Busybox, hasn't been discovered. It might be hard cancelled via resistor or soft cancelled via boot parameter.
-FIXME //Replace EXAMPLE by real values.// +
-</WRAP>+
  
-^ Serial connection parameters\\ for Arcadyan / Astoria prv3399B-E-LT @@Version@@ EXAMPLE 115200, 8N1 |+See photo below for the pinout of the Serial Port of this specific device:\\ 
 +{{ :media:arcadyan:prv3399b:prv3399b_uart_jtag_and_flash_hack.jpg?direct&400 |}} 
 + 
 +You will need some soldering skills though to really have access to it. 
 + 
 +^ Serial connection parameters\\ for Arcadyan / Astoria prv3399B-E-LT |  115200, 8N1 |
  
 ==== JTAG ==== ==== JTAG ====
 -> [[docs:techref:hardware:port.jtag]] general information about the JTAG port, JTAG cable, etc. -> [[docs:techref:hardware:port.jtag]] general information about the JTAG port, JTAG cable, etc.
  
-How to connect to the JTAG Port of this specific device:\\ +**This is not confirmed** but there're several unpopulated pins on the board. Some of them are known to be UART, it might be well that the rest of them are for JTAG:\\ 
-**Insert photo of PCB with markings for JTAG port**+{{ :media:arcadyan:prv3399b:prv3399b_uart_jtag_and_flash_hack.jpg?direct&400 |}} 
 + 
 + 
 +==== HACKS ==== 
 +=== Soft hacks === 
 + 
 +== Access to web CFE == 
 +First, you will need to gain access to the bootloader CFE and stop the countdown. 
 + 
 +Once there, use your browser to reach: 
 +<code>192.168.1.1</code> 
 + 
 +A fancy menu will pop-up as below: 
 +{{ :media:arcadyan:prv3399b:prv3399b_cfe_web_backdoor.jpg?direct&400 |}} 
 + 
 + 
 +== Enable CFE countdown == 
 +  - First you need to have access to the CFE. You might need this [[#Access to CFE menu|hack]] 
 +  - Now enter command "c" 
 +  - Select "Boot Image" 2 
 +  - Leave the rest of parameters untouched by pressing "intro" 
 + 
 + 
 +=== Hard hacks === 
 +During boot, specific NAND flash pins can be shorcircuited in order to provoke a boot fail and therefore access to bootloader. 
 + 
 +| {{:meta:icons:tango:48px-dialog-warning.svg.png?nolink}} | **WARNING:** This method is considered to be safe but use at your own discretion.\\ | 
 + 
 +== Access to CFE menu == 
 +This hack will need some training and skill. Don't give up! 
 +Basically, we will let the system jump to CFE bootloader and corrupt the loading of any further image from NAND flash. 
 + 
 +  - Switch on the device 
 +  - Let system jump to the "Copyright" line 
 +  - Now shortcircuit pins 8&9. See diagram at the bottom. Use the tip of a needle, thin screwdriver, etc 
 +  - After success, error messages will pop up and you will have access to the CFE command line as follows 
 + 
 +<WRAP bootlog> 
 +<nowiki> 
 +---- 
 +HELO 
 +ZBSS 
 +RAMI 
 + 
 +Copyright (C) 2019 Arcadyan Technology. 
 + 
 +NANDFLASH: 
 +    DEVICE ID: 0x98f18015f2, size: 131072KB, type: SLC 
 +    block: 128KB(1024), page: 2KB, oob: 64Bytes 
 +nandflash_bbt_scan_block: detect bad block marker @ 0x6000000 
 + 
 +NVRAM(0) MAGIC checking passed! 
 +NVRAM(0) CRC checking passed! 
 +total 10 of NVRAM(0) entries loaded 
 + 
 +NVRAM(1) MAGIC checking passed! 
 +NVRAM(1) CRC checking passed! 
 +total 10 of NVRAM(1) entries loaded 
 + 
 +BOOTLOADER version 1.2.4 for PRV3397B_E_LT 
 +Build Date: Tue Apr 25 13:45:35 2017 (tinghung_chen@buildbed) 
 + 
 +Chip ID: BCM68380B0 MIPS: 600MHz, DDR: 533MHz, Bus: 240MHz, RDP: 800MHz 
 +Memory Test Passed! 
 +Total Memory: 268435456 bytes (256MB) 
 +*** Press any key to stop auto run (0 seconds) *** 
 +Auto run second count down: 0 
 +Loading secondary image ... 
 +ERROR: data is invalid and not correctable at offset 0x2b00000 
 +Could not read from flash: CFE error -4 
 +enable IH Wan-Wan forwarding... 
 +data_path_go Done!! 
 +Set EMAC4 as RGMII 
 +Creating CPU ring for queue number 0 with 32 packets descriptor=0x8b58cb60 
 + Done initializing Ring 0 Base=0xad0141e0K End=0xad0143e0K calculated entries= 32 RDD Base=0x0d0141e0K descriptor=0x8b58cb60 
 +Open PHY 1 on MAC 0 : link state = Down 
 +Open PHY 2 on MAC 1 : link state = Down 
 +Open PHY 3 on MAC 2 : link state = Down 
 +Open PHY 4 on MAC 3 : link state = Down 
 +Open PHY 0 on MAC 4 : link state = Down 
 +web info: Waiting for connection on socket 0. 
 +PRV3397B_E_LT> 
 +</nowiki> 
 +</WRAP> 
 +\\ 
 +**Congratulations!** Now you can consider enabling the bootloader countdown and therefore have CFE always reachable. See [[#Enable CFE countdown|this]] 
 + 
 +{{ :media:arcadyan:prv3399b:prv3399b_uart_jtag_and_flash_hack.jpg?direct&400 |}} 
 + 
 +==== CFE menu ==== 
 +Using the CFE hack above, now you can enter the menu of the bootloader: 
 + 
 +This is a piece of obscured software; seems an Arcadyan customized version of the CFE with little options. 
 + 
 +<code> 
 +RV3397B_E_LT>  help 
 +Available commands: 
 + 
 +sc                  Update certificate 
 +show devices        Display information about the installed devices. 
 +erasepart           Erase the specified partition 
 +m                   Change the board's manufacture setting 
 +c                   Change the board's setting 
 +uc                  Update certificate file 
 +u                   Update 1st/2nd flash image or bootloader 
 +br                  Boot program from 1st/2nd cferam2 
 +r                   Reset the board 
 +help                Obtain help for CFE commands 
 + 
 +</code> 
 + 
 +===== Flash partition ===== 
 +==== OEM partition ==== 
 +As reported by bootloader: 
 +<code> 
 +PRV3397B_E_LT>show devices 
 +Device Name          Description 
 +-------------------  --------------------------------------------------------- 
 +uart0                BCM63xx DUART channel 0 
 +nandflash0.bootldr   offset 00000000 size 512KB 
 +nandflash0.ca        offset 00080000 size 512KB 
 +nandflash0.manufac   offset 00100000 size 512KB 
 +nandflash0.nvram     offset 00180000 size 512KB 
 +nandflash0.pri_boot  offset 00200000 size 512KB 
 +nandflash0.pri_linu  offset 00280000 size 5120KB 
 +nandflash0.pri_root  offset 00780000 size 35840KB 
 +nandflash0.sec_boot  offset 02A80000 size 512KB 
 +nandflash0.sec_linu  offset 02B00000 size 5120KB 
 +nandflash0.sec_root  offset 03000000 size 35840KB 
 +nandflash0.pri_cfg   offset 05300000 size 512KB 
 +nandflash0.sec_cfg   offset 05380000 size 512KB 
 +nandflash0.softrip   offset 05400000 size 512KB 
 +nandflash0.softuser  offset 05480000 size 512KB 
 +nandflash0.ubifs     offset 05500000 size 43008KB 
 +nandflash0.oops_dat  offset 07F00000 size 1024KB 
 +eth0 
 +                     YàYYYE$ 
 +                            Yø 
 +*** command status = 0 
 +PRV3397B_E_LT> 
 +</code>
  
 ===== Bootlogs ===== ===== Bootlogs =====
-==== OEM bootlog ====+==== OEM Early bootlog ==== 
 +This info is taken from the early UART.
 <WRAP bootlog> <WRAP bootlog>
-<nowiki>COPY HERE THE BOOTLOG WITH THE ORIGINAL FIRMWARE</nowiki>+<nowiki> 
 +---- 
 +BTL1 
 +HELO 
 +CPUI 
 +L1CI 
 +CPUI 
 +L1CI 
 +ZBSS 
 +CODE 
 +DATA 
 +L12F 
 +MAIN 
 +OTP? 
 +OTPP 
 +ROTB 
 +SCBT 
 +NAND 
 +IMG? 
 +IMGL 
 +HDR? 
 +HDRP 
 +MCV? 
 +KEY? 
 +KEYA 
 +MID? 
 +MIDP 
 +MCVA 
 +SBI? 
 +SBIA 
 +PASS 
 +---- 
 +HELO 
 +CPUI 
 +L1CI 
 +PLLI 
 +PMCB 
 +DRAM 
 +---- 
 +PHYS 
 +ZQDN 
 +PHYE 
 +DINT 
 +TST1 
 +TST2 
 +PASS 
 +---- 
 +ZBSS 
 +L12F 
 +ROMI 
 +PSRA 
 +PSRB 
 +PSRC 
 +PSRD 
 +PSRE 
 +---- 
 +HELO 
 +ZBSS 
 +RAMI 
 + 
 +Copyright (C) 2017 Arcadyan Technology. 
 + 
 +NANDFLASH: 
 +    DEVICE ID: 0x98f18015f2, size: 131072KB, type: SLC 
 +    block: 128KB(1024), page: 2KB, oob: 64Bytes 
 +nandflash_bbt_scan_block: detect bad block marker @ 0x6000000 
 + 
 +NVRAM(0) MAGIC checking passed! 
 +NVRAM(0) CRC checking passed! 
 +total 10 of NVRAM(0) entries loaded 
 + 
 +NVRAM(1) MAGIC checking passed! 
 +NVRAM(1) CRC checking passed! 
 +total 10 of NVRAM(1) entries loaded 
 + 
 +BOOTLOADER version 1.2.4 for PRV3397B_E_LT 
 +Build Date: Tue Apr 25 13:45:35 2017 (paul_shih@buildbox1) 
 + 
 +Chip ID: BCM68380B0 MIPS: 600MHz, DDR: 533MHz, Bus: 240MHz, RDP: 800MHz 
 +Memory Test Passed! 
 +Total Memory: 268435456 bytes (256MB) 
 +Board IP address        192.168.1.1 
 +Board IP netmask        255.255.255.0 
 +Gateway IP address      0.0.0.0 
 +Server IP address       192.168.1.99 
 +Boot image (1 or 2)     2 
 +Temp boot (0, 1 or 2)   0 
 +Boot countdown delay (0 to 3)   0 
 +Serial number           ARLT83733412 
 +MAC address number      4 
 +MAC address base        4C-1B-86-59-4E-56 
 +Wireless SSID   4E56 
 +Wireless key    2WU2pKex 
 +Wireless WPS pin        53478306 
 +Admin password  2WU2pKex 
 +Hardware version        R01 
 +Manufacturing mode (0 or 1)     0 
 +*** Press any key to stop auto run (0 seconds) *** 
 +Auto run second count down: 0 
 +Loading secondary bootram ... 
 +Decryption OK! 
 +Decompression OK! 
 +Entry at 0x8b500000 
 +Starting program at 0x8b500000 
 +---- 
 +HELO 
 +ZBSS 
 +RAMI 
 + 
 +Copyright (C) 2019 Arcadyan Technology. 
 + 
 +NANDFLASH: 
 +    DEVICE ID: 0x98f18015f2, size: 131072KB, type: SLC 
 +    block: 128KB(1024), page: 2KB, oob: 64Bytes 
 +nandflash_bbt_scan_block: detect bad block marker @ 0x6000000 
 + 
 +NVRAM(0) MAGIC checking passed! 
 +NVRAM(0) CRC checking passed! 
 +total 10 of NVRAM(0) entries loaded 
 + 
 +NVRAM(1) MAGIC checking passed! 
 +NVRAM(1) CRC checking passed! 
 +total 10 of NVRAM(1) entries loaded 
 + 
 +BOOTLOADER version 1.2.4 for PRV3397B_E_LT 
 +Build Date: Tue Apr 25 13:45:35 2017 (tinghung_chen@buildbed) 
 + 
 +Chip ID: BCM68380B0 MIPS: 600MHz, DDR: 533MHz, Bus: 240MHz, RDP: 800MHz 
 +Memory Test Passed! 
 +Total Memory: 268435456 bytes (256MB) 
 +*** Press any key to stop auto run (0 seconds) *** 
 +Auto run second count down: 0 
 +Loading secondary image ... 
 +Finished loading 5242880 bytes 
 +DATE    : Fri Oct 25 18:13:05 2019 
 +VER     : v1.03.05.217 
 +CRC     : 3C183963 
 +CRC OK! 
 +Signature OK! 
 +Decryption OK! 
 +Decompression OK! 
 +Code Address: 0x80010000, Entry Address: 0x80451a20 
 +Starting program at 0x80451a20 
 + 
 + 
 +</nowiki>
 </WRAP>\\ </WRAP>\\
 +
 +==== OEM OS bootlog ====
 +This info is taken from the OS UART.
 +<WRAP bootlog>
 +<nowiki>
 +Quantenna Mini U-Boot
 +Version: v37.4.0.28 Built: Oct 26 2015 at 19:23:50
 +br
 +1G-FD
 +Using br device
 +TFTP from server 1.1.1.1; our IP address is 1.1.1.2
 +Filename 'u-boot.bin'.
 +Load address: 0x88000000
 +Loading: T ##############
 +done
 +Bytes transferred = 69872 (0x110f0)
 +Boot reached stage 13
 +Boot reached stage 12
 +Valid CRC found in flash restoring env...
 +Boot reached stage 11
 +hw_config_id 65535: 'QTM840_5S3_MAC'
 +Cold boot
 +Reset status: 0x00000001
 +
 +Info: data uncached: addr=0xc0000000 size=1024MB
 +Info: text at 0x88040000, stack at 0x88013ffc(8192), heap at 0x88000000(73728), uboot size 173708
 +Info: i-cache is enabled
 +Info: d-cache is enabled
 +Info: CPU freq is 500000000, dev freq is 125000000
 +
 +Info: Quantenna U-Boot version:v37.4.0.136
 +Info: build date 'May 10 2019', time '23:46:47'
 +
 +SPI flash info:
 +        name             : w25x05
 +        jedec_id         : 0xef3010
 +        sector size      : 4096
 +        number of sector : 16
 +        frequency        : 104000000
 +        flags            : 0x2
 +        lock             :
 +DDR_INIT: type = 16, speed = 2, size = 134217728, rev = 0x43, param = 0x0
 +DDR_INIT: replacing invalid param = 0x0 with default 0xe7b
 +500MHz
 +BDA at 0x80002000
 +In:    serial
 +Out:   serial
 +Err:   serial
 +Boot reached stage 64
 +Boot reached stage 65
 +br
 +Hit any key to stop autoboot:  0
 +Boot reached stage 80
 +1G-FD
 +Using br device
 +TFTP from server 1.1.1.1; our IP address is 1.1.1.2
 +Filename 'topaz-linux.lzma.img'.
 +Load address: 0x83000000
 +Loading: #################################################################
 +         #################################################################
 +         #################################################################
 +         #################################################################
 +         #################################################################
 +         #################################################################
 +         #################################################################
 +         #################################################################
 +         #################################################################
 +         #################################################################
 +         #################################################################
 +         #################################################################
 +         #################################################################
 +         #################################################################
 +         #################################################################
 +         #################################################################
 +         #################################################################
 +         ##################################
 +done
 +Bytes transferred = 5831576 (0x58fb98)
 +Boot reached stage 81
 +Boot reached stage 84
 +Boot reached stage 1
 +## Booting kernel from Legacy Image at 83000000 ...
 +Boot reached stage 2
 +Boot reached stage 3
 +   Image Name:   topaz-linux
 +   Image Type:   arc Linux Kernel Image (lzma compressed)
 +   Data Size:    5823384 Bytes =  5.6 MB
 +   Load Address: 8493a000
 +   Entry Point:  8493a000
 +   Qtn flags:    00000001
 +   Verifying Checksum ... OK
 +Boot reached stage 4
 +Boot reached stage 5
 +Boot reached stage 6
 +Boot reached stage 14
 +   Uncompressing Kernel Image ... OK
 +Boot reached stage 7
 +Boot reached stage 8
 +Command line TAG setup
 +Params->u.cmdline.cmdline console=ttyS0,115200n8 earlyprintk=1 hw_config_id=65535
 +p console=ttyS0,115200n8 earlyprintk=1 hw_config_id=65535
 +##  Unset TAG qtn_flags 1
 +## Transferring control to Linux (at address 8493a000) ATAG parameters 88067d94 - 88067dec...
 +[    0.000000] Linux version 2.6.35.12 (tinghung_chen@buildbed) (gcc version 4.2.1 (ARC_2.3)) #2 Tue May 28 16:51:36 CST 2019
 +[    0.000000] Parsing ATAG parameters from bootloader
 +[    0.000000] ATAG_CORE: successful parsing
 +[    0.000000] ATAG_CMDLINE: command line = console=ttyS0,115200n8 earlyprintk=1 hw_config_id=65535
 +[    0.000000] Board id: 65535
 +[    0.000000] ATAG_HW_CONFIG_ID: hw_config_id = 65535
 +[    0.000000]
 +[    0.000000] Processor Family: ARC 700 [0x33]
 +[    0.000000] CPU speed :      500.00 Mhz
 +[    0.000000] Timers:  TIMER1 TIMER0
 +[    0.000000] Interrupt Vect Base:     0x88052400
 +[    0.000000] Peripheral Base: NOT present; assuming 0xCOFC0000
 +[    0.000000] Data UNCACHED Base (I/O): start 0xc0 Sz, 1024 MB
 +[    0.000000] ARC700 MMU Ver [2]
 +[    0.000000]    PAGE SIZE 8k
 +[    0.000000]    JTLB 128 x 2 = 256 entries
 +[    0.000000]    uDTLB 8 entr, uITLB 4 entr
 +[    0.000000] TLB Refill "will NOT" Flush uTLBs
 +[    0.000000] Detected I-cache :
 +[    0.000000]   Type=2 way set-assoc, Line length=32, Size=16K (enabled)
 +[    0.000000] Detected D-cache :
 +[    0.000000]   Type=4 way set-assoc, Line length=32, Size=16K (enabled)
 +[    0.000000] Extensions:
 +[    0.000000]    MPY: 32x32 with ANY Result Reg   MAC MPY: Dual 16 x 16 and 32 x 16
 +[    0.000000]    DCCM: N/A  ICCM: N/A
 +[    0.000000]    CRC: N/A,   SWAP: Present   NORM: Present
 +[    0.000000]    Min-Max: Present,   Barrel Shifter: Present
 +[    0.000000]    Ext Arith Insn: Present
 +[    0.000000] Floating Point Extension: N/A
 +[    0.000000] On node 0 totalpages: 16383
 +[    0.000000] free_area_init_node: node 0, pgdat 85b55dac, node_mem_map 85c06024
 +[    0.000000]   Normal zone: 72 pages used for memmap
 +[    0.000000]   Normal zone: 0 pages reserved
 +[    0.000000]   Normal zone: 16311 pages, LIFO batch:3
 +[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16311
 +[    0.000000] Kernel command line: console=ttyS0,115200n8 earlyprintk=1 hw_config_id=65535
 +[    0.000000] bootconsole [ruby_early0] enabled
 +[    0.000000] PID hash table entries: 512 (order: -2, 2048 bytes)
 +[    0.000000] Dentry cache hash table entries: 16384 (order: 3, 65536 bytes)
 +[    0.000000] Inode-cache hash table entries: 8192 (order: 2, 32768 bytes)
 +[    0.000000] Memory: 36088KB available (2165K code,1202K data, 15872K init)
 +[    0.000000] Hierarchical RCU implementation.
 +[    0.000000]  RCU debugfs-based tracing is enabled.
 +[    0.000000]  Verbose stalled-CPUs detection is disabled.
 +[    0.000000] clockevent mode switch to [1]
 +[    0.000000] clockevent mode switch to [2]
 +[    0.000000] Calibrating delay loop... 249.03 BogoMIPS (lpj=622592)
 +[    0.115000] pid_max: default: 4096 minimum: 301
 +[    0.120000] Mount-cache hash table entries: 1024
 +[    0.125000] Starting run_ksoftirqd, stack (thread_info) at 85b7a000 cpu 0
 +[    0.130000] NET: Registered protocol family 16
 +[    0.135000] Topaz heap 1 in SRAM 88016360<->88020000
 +[    0.140000] Topaz heap 2 in SRAM 88011000<->88012000
 +[    0.150000] bio: create slab <bio-0> at 0
 +[    0.160000] watch64: 2003/08/22 Josef 'Jeff' Sipek <jeffpc@xxxxxxxxxxxxx>
 +[    0.165000] watch64: Enabling Watch64 extensions...done.
 +[    0.170000] Switching to clocksource ARC Timer1
 +[    0.175000] NET: Registered protocol family 2
 +[    0.180000] IP route cache hash table entries: 2048 (order: 0, 8192 bytes)
 +[    0.185000] TCP established hash table entries: 4096 (order: 2, 32768 bytes)
 +[    0.195000] TCP bind hash table entries: 4096 (order: 1, 16384 bytes)
 +[    0.200000] TCP: Hash tables configured (established 4096 bind 4096)
 +[    0.205000] TCP reno registered
 +[    0.210000] NET: Registered protocol family 1
 +[    0.815000] JFFS2 version 2.2. (NAND) c 2001-2006 Red Hat, Inc.
 +[    0.820000] msgmni has been set to 70
 +[    0.825000] io scheduler noop registered (default)
 +[    1.250000] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
 +[    1.255000] serial8250.0: ttyS0 at MMIO 0xf0000000 (irq = 48) is a 16550A
 +[    1.260000] console [ttyS0] enabled, bootconsole disabled
 +[    1.260000] console [ttyS0] enabled, bootconsole disabled
 +[    1.265000] brd: module loaded
 +[    1.275000] loop: module loaded
 +[    1.280000] spi_flash: Force not to support Protect Mode
 +[    1.285000] Creating 3 MTD partitions on "spi_flash":
 +[    1.290000] 0x000000000000-0x000000005000 : "uboot"
 +[    1.300000] 0x000000005000-0x00000000b000 : "uboot_env"
 +[    1.310000] 0x00000000b000-0x000000010000 : "data"
 +[    1.315000] spi_flash: SPI flash driver initialized successfully!
 +[    1.320000] ruby_health loading
 +[    1.325000] HBM pool: emac rx 0x0 to 0x8000, wmac rx 0x8000 to 0xa000
 +[    1.720000] HBM meta: emac rx 0x63c040 to 0x6bc040, wmac rx 0x6bc080 to 0x6dc080
 +[    1.725000] topaz_hbm_init_pool_list pool 0 pool_list 0x88000000 bus_range 0x16ec400 to 0x26ec400 sz 2048 count 8192
 +[    1.725000] topaz_hbm_init_pool_list pool 1 pool_list 0x88008000 bus_range 0x26fc400 to 0x48fc400 sz 17408 count 2048
 +[    1.725000] topaz_hbm_init_pool_list pool 3 pool_list 0x8800a000 bus_range 0x0 to 0x0 sz 0 count 4096
 +[    1.730000] topaz_busmon_init success
 +[    1.735000] topaz_temp_sens_init success
 +[    1.740000] u32 classifier
 +[    1.740000]     input device check on
 +[    1.745000]     Actions configured
 +[    1.750000] Netfilter messages via NETLINK v0.30.
 +[    1.755000] nf_conntrack version 0.5.0 (563 buckets, 2252 max)
 +[    1.760000] ip_tables: (C) 2000-2006 Netfilter Core Team
 +[    1.765000] TCP cubic registered
 +[    1.770000] NET: Registered protocol family 10
 +[    1.775000] NET: Registered protocol family 17
 +[    1.780000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
 +[    1.785000] All bugs added by David S. Miller <davem@redhat.com>
 +[    1.795000] Freeing unused kernel memory: 15872k freed [8493a000] TO [858ba000]
 +[    1.800000] Common mmap addr-space starts 2c0f0000
 +init started: BusyBox v1.10.3 (2019-05-28 16:43:09 CST)
 +starting pid 44, tty '': '/etc/init.d/rcS'
 +[    2.180000] load_module: 'bootcfg' using DRAM (offset:0x85800000, size:0x96b0)
 +Starting portmap: done
 +Initializing random number generator... done.
 +/mnt/jffs2/wireless_conf.txt not found. Creating a default conf file
 +restore_wireless_conf
 +restore_wireless_conf: wifi_mode = default
 +restore_wireless_conf: Setting default wireless config params
 +restore_wireless_conf: board_id = 65535
 +restore_wireless_conf: board_name = QTM840_5S3_MAC
 +restore_wireless_conf: Writing config params to /mnt/jffs2/wireless_conf.txt
 +Starting network...
 +[    3.500000] load_module: 'rtl8367b' using DRAM (offset:0x86700000, size:0x32a77)
 +[    3.505000] rtl8367b: module license 'unspecified' taints kernel.
 +[    3.510000] Disabling lock debugging due to kernel taint
 +[    3.565000] load_module: 'emaclib' using DRAM (offset:0x85870000, size:0x53c1)
 +[    3.685000] load_module: 'switch_vlan' using DRAM (offset:0x85858000, size:0x2739), SRAM (offset:0x88016368, size:0x1)
 +[    3.790000] load_module: 'switch_tqe' using DRAM (offset:0x85850000, size:0x3b3a), SRAM (offset:0x88016378, size:0x1a10)
 +[    3.840000] tqe_descs_alloc: 2048 tqe_rx_descriptors at kern uncached 0x580e1da0 bus 0x80017da0
 +[    3.920000] load_module: 'fwt_if' using DRAM (offset:0x85898000, size:0x1af7)
 +[    3.955000] load_module: 'fwt_ctrl' using DRAM (offset:0x86740000, size:0x23a01)
 +[    4.010000] load_module: 'dpi' using DRAM (offset:0x85892000, size:0x1d9f)
 +[    4.045000] load_module: 'switch_emac' using DRAM (offset:0x85cec000, size:0x2563), SRAM (offset:0x88011a40, size:0x2f8)
 +[    4.110000] emac wbsp: 0
 +[    4.115000] enable A2 (single)
 +[    4.175000] Random stuff 2D
 +emac0 is eth1_0, emac1 is unused
 +Stateless mode. Using temporary ip address:
 +Using IP address 1.1.1.2
 +Netmask is not set
 +[    4.445000] emac_lib eth1_0: force link (1000/Full)
 +[    4.565000] device eth1_0 entered promiscuous mode
 +[    4.570000] br0: port 1(eth1_0) entering forwarding state
 +[    4.575000] br0: port 1(eth1_0) entering forwarding state
 +[    4.605000] FWT: [00:aa:bb:cc:dd:02] add entry, port:emac0 node:0 index:876 4addr:0 entries:1
 +/sbin/ifup -a
 +ifconfig: SIOCGIFFLAGS: No such device
 +Version of /proc/bootcfg/qtn_regulatory_db.bin is Regulatory db version: v37.3.0.21
 +Version of /etc/qtn_regulatory_db.bin is Regulatory db version: v37.4.0.171
 +Selected database version: Regulatory db version: v37.4.0.171
 +Using /etc/qtn_regulatory_db.bin
 +Starting qevt_server
 +Starting inetd ...
 +/scripts/cmdloop starting /sbin/qevt_server, at 00:00:05 up 0 min, load average: 0.08, 0.01, 0.00
 +[    5.880000] load_module: 'hw_rev' using DRAM (offset:0x85834000, size:0x374c)
 +Starting wireless...
 +restore_default_config -nr
 +restore_wireless_conf ap
 +restore_wireless_conf: wifi_mode = ap
 +restore_wireless_conf: Setting default wireless config params
 +restore_wireless_conf: board_id = 65535
 +restore_wireless_conf: board_name = QTM840_5S3_MAC
 +restore_wireless_conf: Writing config params to /mnt/jffs2/wireless_conf.txt
 +restore_default_config: Updating security config files for mode ap
 +restore_default_config: Removing block ACK restrictions
 +restore_default_config: Configuration has been set to default values. Reboot after customizing to ensure correct operation.
 +complete
 +/scripts/cmdloop starting /sbin/qcsapi_rpcd, at 00:00:07 up 0 min, load average: 0.08, 0.01, 0.00
 +/scripts/cmdloop starting /sbin/call_qcsapi_rpcd, at 00:00:07 up 0 min, load average: 0.08, 0.01, 0.00
 +'monitor_temperature' is not enabled/set
 +MAUI service started
 +/etc/init.d/S91dhclient: line 26: syntax error: "else" unexpected
 +/scripts/cmdloop starting /sbin/qharvestd, at 00:00:10 up 0 min, load average: 0.47, 0.09, 0.03
 +Starting httpd
 +cp: cannot stat '/etc/minihttpd.conf': No such file or directory
 +qharvestd[notice]: qharvestd v1.32.2 started
 +starting pid 691, tty '/dev/console': '/bin/sh -l'
 +
 +
 +BusyBox v1.10.3 (2019-05-28 16:43:09 CST) built-in shell (ash)
 +Enter 'help' for a list of built-in commands.
 +
 +quantenna # qharvestd[error]: qcsapi[interface_get_mac_addr] failed, err code = -19 (No such device)
 +
 +/scripts/readmem: line 10: cannot create /proc/wlanmem: nonexistent directory
 +cat: can't open '/proc/wlanmem': No such file or directory
 +qharvestd[error]: qcsapi[get_carrier_id] failed, err code = -19 (No such device)
 +
 +qharvestd[error]: failed to get device MAC address
 +qharvestd[notice]: qharvest terminated
 +Using IP address 1.1.1.2
 +Netmask is not set
 +ifconfig: bad address ''
 +Loading modules
 +[   13.550000] load_module: 'qtn_debug' using DRAM (offset:0x85838800, size:0x377)
 +[   13.670000] load_module: 'i2cbus' using DRAM (offset:0x85856000, size:0x1ce2)
 +[   13.825000] load_module: 'qtsens' using DRAM (offset:0x850d6000, size:0x7b6)
 +[   13.955000] load_module: 'pm_interval' using DRAM (offset:0x84960000, size:0x13b2)
 +[   14.140000] load_module: 'wlan' using DRAM (offset:0x84a00000, size:0xb9100)
 +[   14.485000] wlan: 0.8.4.2 (0.9.3.3)
 +[   14.650000] load_module: 'auc_fw' using DRAM (offset:0x866ec000, size:0x8cb)
 +[   14.755000] load_module: 'qvspmod' using DRAM (offset:0x84eb0000, size:0x3f39)
 +[   14.785000] QVSP module init
 +[   14.860000] load_module: 'qdrv' using DRAM (offset:0x84c00000, size:0xa9a40)
 +[   15.170000] qdrv wbsp: 0
 +[   15.315000] load_module: 'wlan_xauth' using DRAM (offset:0x84eb9000, size:0x32f)
 +[   15.330000] br0: no IPv6 routers present
 +[   15.485000] load_module: 'wlan_ccmp' using DRAM (offset:0x84962000, size:0x1782)
 +[   15.660000] load_module: 'wlan_tkip' using DRAM (offset:0x85860000, size:0x2636)
 +Loading MuC driver (qtn_driver.qtn_ruby.0.bin)
 +no keyfile specified
 +unable to load Public Key
 +Waiting for Wireless Events from interfaces...
 +Found power table in /etc/power_tables
 +[   16.985000] set power_selection 2
 +[   16.990000] qdrv_soc_publish_params: parames->tqe_sem_en 0, auc_tqe_sem_en 0
 +[   17.000000] ..... Current RFIC Chip ID -- 4
 +[   17.295000] AuC SRAM start 0x88040000 end 0x88080000 size 262144
 +[   17.300000] AuC is configured for non-MU SRAM layout
 +[   17.305000] AuC SRAM bank 0 start 0x88040000 end 0x88050000
 +[   17.310000] AuC SRAM bank 1 start 0x88050000 end 0x88060000
 +[   17.315000] AuC SRAM bank 2 start 0x88060000 end 0x88070000
 +[   17.320000] AuC SRAM bank 3 start 0x88070000 end 0x88080000
 +[   17.350000] MuC: g_tqe_sem_en 0
 +[   17.350000] MuC: build date Wed, 03 Oct 2018 14:35:42 -0700
 +[   17.355000] MuC: slow heap begin=0x002a33e0 end=0x004203e0
 +[   17.360000] MuC: fast heap begin=0x80030800 end=0x80037000
 +[   17.365000] MuC: stack start=0x8003ef80 sp=0x8003f6d4
 +[   17.370000] MuC: calstate is 3 (prod), dcache on
 +[   17.375000] MuC: RFIC version 1 rev 0
 +[   17.405000] qdrv_mac_reserve_clear: mac reservation table cleared
 +[   17.430000] QDRV: I2C dapter not found
 +[   17.445000] MuC: bb_init: FEM 0x7 bw_mode 0 chan 0 11b 0 11a 1
 +[   17.450000] MuC: set max/nrm gain(0x27) done.
 +[   17.455000] MuC: set cca threshold!
 +[   17.455000] MuC: rf_optimizing_rf_register_map, set rf to 0x75
 +[   17.460000] MuC: os_uc, after bb_rf_complete_attach.
 +[   17.465000] MuC: WMAC0: hal fd start=0xe5040300 count=48 size=108 end=0xe5041740
 +[   17.470000] MuC: WMAC1: hal fd start=0xe5140d50 count=8 size=84 end=0xe5140ff0
 +[   17.475000] MuC: freq 1 proj 1
 +[   17.475000] MuC: dynamic one-bit autocorrelation enabled
 +[   17.480000] MuC: QMAT SRAM base 0x80070000
 +[   17.485000] MuC: enable IRQs
 +[   17.610000] qdrv_mu_stat_init
 +[   17.685000] MuC: AuC enabled 0xe5101cd0/0x60063630 il 0xe5101284/0xe5101288 stats 0x60061170/0x600633700x6007e140
 +[   17.690000] MuC: Update MU debug flag failed. keep old value : 0x00000000
 +[   17.695000] QDRV: hardware is 4x4 11ac FO RGMII/PCIe QV840
 +[   17.700000] MuC boot succeeded 0.085 seconds
 +start-vap ap
 +[   19.280000] load_module: 'wlan_scan_ap' using DRAM (offset:0x85f20000, size:0x3176)
 +[   19.360000] QTM daemon registered
 +[   19.480000] qvsp_nl_node_init: QVSP not initialized
 +[   19.485000] MuC: qtn_mu_ndpa_setup: bw_cap 2 done
 +[   19.500000] VAP create succeeded 0.010 seconds
 +[   19.510000] MuC: qtn_mu_ndpa_setup: bw_cap 2 done
 +[   19.995000] MuC: calibration ver 0x801
 +bss_tm set to 1
 +neigh_repo reset to 0
 +radar in 80MHZ mode
 +Setting mode to 11ac80
 +set_region: Setting regulatory region dev_name=wifi0 region=es mode=ap repeater=0
 +radar start with[   21.865000] DFS_s_radio: parameters updated, region: eu
 + regulatory eu
 +[   21.870000] MuC: macfw: radar_start.........
 +[   21.875000] MuC: radar_start, region eu = 2
 +[   22.120000] qdrv_radar_enable_action: ERROR - radar already enabled
 +ICAC: max_boot_cac is greater than 0, hence the parameter non_dfs_channel is ignored. To avoid doing initial CAC set max_boot_cac to 0.
 +dfs_s_radio 1 dfs 0 non-dfs 0 scan 0 auto-channel  channel 0
 +Configure max_boot_cac to 70
 +[   23.005000] device wifi0 entered promiscuous mode
 +[   23.125000] Enabling SSDP flooding
 +Beamforming enabled
 +[   24.175000] Enabling SCS
 +SCS enabled
 +QTM: load profile off
 +QTM enabled: 0
 +[   25.375000] MuC: Beacon scheme updated to 1
 +[   25.420000] Starting DFS seamless radio...
 +[   25.435000] BRIDGE WLAN report flood-forwarding enabled
 +QCS API error 1010: Cannot contact security manager
 +No core dump generated
 +QCS API error 34: Parameter value out of range
 +[   27.280000] Build name:            v37.4.0.180
 +[   27.285000] Build revision:        86411
 +[   27.290000] Build type:            SDK
 +[   27.295000] Build timestamp:       1538603078
 +[   27.300000] Platform ID:           432
 +[   27.300000] Hardware ID:           QV840
 +[   27.305000] Hardware revision:     bbic4_rev_a2
 +[   27.310000] Band:                  5GHz
 +[   27.315000] Kernel version:        2.6.35
 +[   27.320000] Calibration version:   disabled
 +[   27.325000] DC/IQ cal version:     V8.1
 +[   27.325000] Power cal version:     V8.1
 +[   27.330000] MuC firmware:          qtn_driver.qtn_ruby.0.bin
 +[   27.335000] DSP firmware:          rdsp_driver.0.bin
 +[   27.340000] AuC firmware:          auc_driver.nomu.0.bin
 +[   27.345000] MAC address 0:         4c:1b:86:59:4e:59
 +[   27.350000] MAC address 1:         00:00:00:00:00:00
 +[   27.355000] Recommended U-Boot:    v37.4.0.136
 +Carrier ID 0, uboot update flag 0
 +complete
 +MU-MIMO is not supported on this device
 +Starting qrpe daemon...
 +qtna-rpe(7.0.10-7e833fa) started
 +PTA request polarity set to 0
 +PTA grant polarity set to 0
 +PTA disabled
 +/scripts/cmdloop starting /sbin/qharvestd, at 01:00:32 up 0 min, load average: 0.80, 0.20, 0.06
 +qharvestd[notice]: qharvestd v1.32.2 started
 +radar start with regulatory eu
 +[   32.395000] qdrv_radar_is_rdetection_required: ERROR - channel not yet set
 +[   32.395000] qdrv_radar_enable_action: ERROR - radar already enabled
 +qharvestd[notice]: Pktlogger support detected
 +qharvestd[info]: rest for 120s (120s 0ms after adjustment)
 +[   32.830000] channel 52 is added into non-primary channel list
 +[   32.870000] channel 56 is added into non-primary channel list
 +[   32.910000] channel 60 is added into non-primary channel list
 +[   32.950000] channel 64 is added into non-primary channel list
 +[   32.950000] Warning: all the sub channels are not in primary channel list!
 +[   32.995000] channel 116 is added into non-primary channel list
 +[   33.035000] channel 120 is added into non-primary channel list
 +[   33.075000] channel 124 is added into non-primary channel list
 +[   33.115000] channel 128 is added into non-primary channel list
 +[   33.115000] Warning: all the sub channels are not in primary channel list!
 +[   33.160000] channel 132 is added into non-primary channel list
 +[   33.200000] channel 136 is added into non-primary channel list
 +[   33.240000] channel 140 is added into non-primary channel list
 +[   33.325000] Starting DFS seamless radio...
 +[   33.620000] MuC: #RX data path optimal flag 0
 +[   33.625000] MuC: rx_post_init: free 0 rxq 9 9 394 descr 0x8000f000/6592 cache 0x8002aa00/13184
 +[   33.625000] MuC: auto cs is enabled
 +[   33.660000] WPS:
 +                    [  110.560000] RADAR: CAC completed for channel 108 (5540 MHz)
 +[  117.810000] channel 52 is removed from non-primary channel list
 +[  117.855000] channel 56 is removed from non-primary channel list
 +[  117.900000] channel 60 is removed from non-primary channel list
 +[  117.945000] channel 64 is removed from non-primary channel list
 +update_5g_channel: 108
 +[  119.510000] FWT: [00:2a:bb:cc:dd:04] add entry, port:emac0 node:0 index:58 4addr:0 entries:2
 +[  126.140000] VAP create succeeded 0.010 seconds
 +[  126.170000] device wifi1 entered promiscuous mode
 +[  135.350000] br0: port 3(wifi1) entering forwarding state
 +[  135.350000] br0: port 3(wifi1) entering forwarding state
 +[  137.970000] VAP create succeeded 0.010 seconds
 +[  138.000000] device wifi2 entered promiscuous mode
 +[  149.465000] VAP create succeeded 0.010 seconds
 +[  149.490000] device wifi3 entered promiscuous mode
 +qharvestd[info]: start oauth processing at 153.436828331
 +qharvestd[info]: target: https://qharvest-prod.quantenna.com/api/auth/token
 +qharvestd[info]: request: { "username": "1072|4c:1b:86:59:4e:59", "password": "0000", "grant_type": "password", "scope": "device" }
 +qharvestd[error]: curl_easy_perform(): Couldn't resolve host 'qharvest-prod.quantenna.com'
 +
 +qharvestd[info]: finish oauth processing at 153.530159547 (in 93ms)
 +qharvestd[info]: poll_request: exponential backoff scale is 3
 +qharvestd[info]: next poll_request will be in 10 seconds
 +qharvestd[info]: rest for 10s (9s 907ms after adjustment)
 +qharvestd[info]: start oauth processing at 163.451312751
 +qharvestd[info]: target: https://qharvest-prod.quantenna.com/api/auth/token
 +qharvestd[info]: request: { "username": "1072|4c:1b:86:59:4e:59", "password": "0000", "grant_type": "password", "scope": "device" }
 +qharvestd[error]: curl_easy_perform(): Couldn't resolve host 'qharvest-prod.quantenna.com'
 +
 +qharvestd[info]: finish oauth processing at 163.456939859 (in 5ms)
 +qharvestd[info]: poll_request: exponential backoff scale is 4
 +qharvestd[info]: next poll_request will be in 24 seconds
 +qharvestd[info]: rest for 24s (23s 995ms after adjustment)
 +iwpriv wifi0 set_owl_beacon 1
 +iwpriv wifi0 set_coc_ndfs 0
 +update_24g_channel: 1
 +[  182.285000] ARC_24G_CHAN_IN_5G=1
 +qharvestd[info]: start oauth processing at 187.465876831
 +qharvestd[info]: target: https://qharvest-prod.quantenna.com/api/auth/token
 +qharvestd[info]: request: { "username": "1072|4c:1b:86:59:4e:59", "password": "0000", "grant_type": "password", "scope": "device" }
 +qharvestd[error]: curl_easy_perform(): Couldn't resolve host 'qharvest-prod.quantenna.com'
 +
 +qharvestd[info]: finish oauth processing at 187.471585747 (in 5ms)
 +qharvestd[info]: poll_request: exponential backoff scale is 5
 +qharvestd[info]: next poll_request will be in 33 seconds
 +qharvestd[info]: rest for 33s (32s 995ms after adjustment)
 +qharvestd[info]: start oauth processing at 220.480904255
 +qharvestd[info]: target: https://qharvest-prod.quantenna.com/api/auth/token
 +qharvestd[info]: request: { "username": "1072|4c:1b:86:59:4e:59", "password": "0000", "grant_type": "password", "scope": "device" }
 +qharvestd[error]: curl_easy_perform(): Couldn't resolve host 'qharvest-prod.quantenna.com'
 +
 +qharvestd[info]: finish oauth processing at 220.486698935 (in 5ms)
 +qharvestd[info]: poll_request: exponential backoff scale is 6
 +qharvestd[info]: next poll_request will be in 93 seconds
 +qharvestd[info]: rest for 93s (92s 995ms after adjustment)
 +qharvestd[info]: start oauth processing at 313.496165543
 +qharvestd[info]: target: https://qharvest-prod.quantenna.com/api/auth/token
 +qharvestd[info]: request: { "username": "1072|4c:1b:86:59:4e:59", "password": "0000", "grant_type": "password", "scope": "device" }
 +qharvestd[error]: curl_easy_perform(): Couldn't resolve host 'qharvest-prod.quantenna.com'
 +</nowiki>
 +</WRAP>\\
 +
  
 ==== OpenWrt bootlog ==== ==== OpenWrt bootlog ====
  • Last modified: 2022/10/28 08:50
  • by danitool