Arcadyan / Astoria ARV7520CW22-A_LT (AKA Orange Livebox 2.1 v2 (2015)

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

WARNING: Please do not get confused with Livebox 2.1 ARV7519RW, which has a quite different hardware. As both models share almost the same case, please check the label at the bottom of the router.

From 2015 onwards, ISP Orange was installing this model which can be easily mistaken by its predecessor ARV7519RW.

This looks as a cost reduction step since there's just 1 USB port and the ethernet gigabit port is missing.

Not supported.

CPU Ram Flash Network WLAN USB Serial JTag
Lantiq ARX220 @ 500 MHz 128 MiB 128 MiB 4x 10/100 bgn 1x 2.0 Yes ?
Architecture MIPS%20architecture
Vendor Lantiq
Bootloader brnboot v2.01.07
System-On-Chip Lantiq ARX220 V1.1 (PSB50221 EL) (variant of VRX288 v2?)
CPU/Speed 500 MHz
Flash-Chip MX30LF1G08 NAND
Flash size 128 MiB
RAM 128 MiB EM68C16CWQE-25H
Wireless BCM 43217 2.4GHz 802.11bgn
Ethernet 10/100 Mbit/s w/ vlan support
Switch internal SoC switch
USB 1x 2.0
Serial Yes
JTAG Not populated

There's no information about this SoC.

However, there're some hints in Lantiq code about a VRX220 platform, being a variant of VR9.

Reading the chipid memory location at 0xbf107340 leads to:

1st chunk0x0001820Manufacturer
2nd chunk0x2000b713Chipid & revision

Therefore, the chip has the same internal id as VRX288 v1.2 and we expect to be almost fully compatible with it.

The only known difference is the ethernet phy, being only x4 10/100 ports, with no Gb port. This is similar to evaluation board EASY220.

Insert photo of front of the casing

Insert photo of back of the casing

Insert photo of backside label

Insert photo of PCB

  1. Remove the pads (x4)
  2. Remove the screws beneath the pads (x4)
  3. Firmly, detach the outer case from the inner. Most probably you will need a flat screwdriver as lever. Quite surprisingly, the case is well designed and no clips are damaged. Hint: start from the back of the router all around as the arrow shows.

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
The UART port with no pins is located close to the SoC.

Find below the pinout

FIXME Do not connect Vcc to your serial device.

Insert photo of PCB with markings for serial port

Serial connection parameters
for Arcadyan / Astoria ARV7520CW22-A_LT (AKA Orange Livebox 2.1 v2 (2015)
EXAMPLE 115200, 8N1

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

Soft hacks

While switching on the router, a certain combo of buttons will grant you access to hidden functions. You will notice you're there because of the fancy movement of the leds.

Access to tiny kernel/Restore Tool

If buttons reset & wifi are pressed together during switching on, you will get access to recovery menu at

http://192.168.1.1

Access to VR9 menu

If buttons reset & wifi & wps are pressed together during switching on, you will jump immediatly in the serial console to VR9 menu:

ROM VER: 1.1.4
CFG 06
NAND
NAND Read OK
DDR PARAM flash addr 1700000
DDR PARAM:
88888888
001a2520
001a2120
00566301
00566501
00000200

DDR autotuning Rev 1.0
DDR check ok... start booting...

END TUNE DDR
Start booting...........



=======================================================================
Wireless ADSL IAD VR9 Loader v2.01.07 build Oct 22 2014 16:13:17
                    Arcadyan Technology Corporation
=======================================================================



[VR9 Boot]:


Hard hacks

During boot, specific NAND flash pins can be shorcircuited in order to provoke a boot fail and therefore access to bootfail options.

WARNING: This method is considered to be safe. The only fatal error seen, after some brutal manipulation, was the removal of the DDR tuning parameters. However, BRNBOOT is capable of recovering them after performing an autotuning
Access to UART mode
  1. Switch off the device
  2. Shortcircuit pin 8&9. See diagram at the bottom. Use the tip of a needle, thin screwdriver, etc
  3. Switch on the device. You will see the following message:
ROM VER: 1.1.4
CFG 02
UART


Access to VR9 menu

This hack will need some training and skill. Don't give up! Basically, we will let the system jump to brnboot and corrupt the loading of any further image from NAND flash.

  1. Switch off the device
  2. Let system jump to the “Init...” line
  3. Now shortcircuit pins 8&9. See diagram at the bottom. Use the tip of a needle, thin screwdriver, etc
  4. After success, error messages will pop up and you will have access to the VR9 command line

ROM VER: 1.1.4 CFG 06 NAND NAND Read OK DDR PARAM flash addr 1700000 DDR PARAM: 88888888 001a2420 001a2120 00566301 00566301 00000500 DDR autotuning Rev 1.0 DDR check ok... start booting... END TUNE DDR Start booting........... ======================================================================= Wireless ADSL IAD VR9 Loader v2.01.07 build Oct 22 2014 16:13:17 Arcadyan Technology Corporation ======================================================================= Init......read page ECC check ret = -1, addr = 0x01700800 NAND Read Error: addr 0x1700800 read 0x01700000 ERROR: ret = 0 Image Check from FLASH_AREA_IMAGE_1 : Unzipping firmware at 0x80002000 ... with nAREA[2]read page ECC check ret = -1, addr = 0x014FFFF4 NAND Read Error: addr 0x14ffff4 read 0x014FFFF4 ERROR: ret = 0 failed : 4 !! Try unzipping firmware again...read page ECC check ret = -1, addr = 0x00B00800 NAND Read Error: addr 0xb00800 read 0x00B00000 ERROR: ret = 0 failed : 4 !! Unzipping firmware at 0x80002000 ... with nAREA[1]read page ECC check ret = -1, addr = 0x00AFFFF4 NAND Read Error: addr 0xaffff4 read 0x00AFFFF4 ERROR: ret = 0 failed : 4 !! Try unzipping firmware again...read page ECC check ret = -1, addr = 0x00100800 NAND Read Error: addr 0x100800 read 0x00100000 ERROR: ret = 0 failed : 4 !! Unzipping Tiny Kernel at 0x80002000 ... read page ECC check ret = -1, addr = 0x00000000 NAND Read Error: addr 0x0 read 0x00000000 ERROR: ret = 0 failed : 4 !! [VR9 Boot]:


Using the VR9 hack above, now you can enter the menu of the brnbootloader.

This is a piece of litte documented software; on the top of this, the help menus are censored in this version, giving no guiding information.

Nonetheless, we can use the help from older releases:

  1. Press “!” to gain administrator mode
  2. Now the following options will be available *but not visible*. Use them at will
 ======================
 [#] Set Serial Number
 [2] Use Normal Firmware
 [3] Use ART-Testing Firmware
 [9] Taggle ART Firmware Enable/Disable
 [A] Set MAC Address
 [E] Erase Flash
 [G] Run Runtime Code
 [H] Set Options
 [M] Upload to Memory
 [P] Print Boot Params
 [R] Read from Memory
 [T] Memory Test
 [U] Upload to Flash
 [V] Set Board Version
 [W] Write to Memory
 [Y] Go to Memory
 [Z] Dump DDR Ram Register
 [0] Primary = Image 0
 [1] Primary = Image 1
 ======================

Nota: Undocumented option [k] will kick the tiny kernel boot. See log at the bottom.

This section will deal with some interesting features available in the OEM firmware.

Type in the below URL's in your browser once connected to your router. Most of the times you need to have 2 tabs open, first for the identification admin/admin, the second to get to the actual function.

You can check all the article in spanish here. Note: the original article refers to 192.168.2.1 which is not working in our case.

Note: the firmware needs proprietary encryption which is unknown up to date.

http://192.168.1.1/system_firmwarel.stm
http://192.168.1.1/cgi-bin/config.bin

Via port 8000

http://192.168.1.1/usb_wftp_server.stm 

There is an available porting for this board, which is not integrated in openwrt main stream. Sources can be found here

Precompiled binaries, both fully tested, are available also here. You will find:

  • A UART-mode binary, useful in order to make a backup of the nand chip and then flash permanently U-Boot
  • A SPL/TPL U-Boot binary

Via VR9 menu (see above hacks) you can see:

---------------------------------------
    Area            Address      Length
---------------------------------------
[0] Boot            0x00000000    1024K
[1] Image 0         0x00100000   10240K
[2] Image 1         0x00B00000   10240K
[3] Configuration   0x01500000    2048K
[4] Boot Params     0x01700000    2048K
[5] Nvram           0x01900000    1024K
[6] Cert            0x01A00000   32768K
[7] EmergencyValue  0x03A00000    6144K
[8] Configuration2  0x04000000    2048K
[9] All area        0x00000000   67584K
---------------------------------------

ROM VER: 1.1.4 CFG 06 NAND NAND Read OK ROM VER: 1.1.4 CFG 06 NAND NAND Read OK DDR PARAM flash addr 1700000 DDR PARAM: 88888888 001a2420 001a2220 00566401 00566501 00000700 DDR autotuning Rev 1.0 DDR check ok... start booting... END TUNE DDR Start booting........... ======================================================================= Wireless ADSL IAD VR9 Loader v2.01.07 build Oct 22 2014 16:13:17 Arcadyan Technology Corporation ======================================================================= Init...... Get Primary to 0.....Image Check from FLASH_AREA_IMAGE_0 : Unzipping firmware at 0x80002000 ... with nAREA[1][ZIP 3] [ZIP 1] done Ready to run firmware In c_entry() function ... install_exception Co config = 80048483 sys_irq_init ... IrqConnect : IRQ = 53, Handler = 0x80016120 VR9 is A21 chip !!!!, ifx_bsp_basic_mps_decrypt bf001f38 0xbf106a10 : 78 0xbf106a11 : 0 0xbf106a0c : 88 ##### _ftext = 0x80002000 ##### _fdata = 0x80AAD620 ##### __bss_start = 0x80C444E8 ##### end = 0x8618FC1C allocate_memory_after_end> len 1666760, ptr 0x86197c20 ##### Backup Data from 0x80AAD620 to 0x86197C1C~0x8632EAE4 len 1666760 ##### Backup Data completed ##### Backup Data verified [GPIO FLOW] SetGpio() Begin .. ifx_gpio_init() !!! ifx_gpio_pre_init() !!! [KERN_INFO]IFX GPIO driver, version 1.2.10, (c)2009 Infineon Technologies AG Register LED MODULE OK!! Register BUTTON MODULE OK!! [GPIO FLOW] SetGpio() End. [INIT] System Log Pool startup ... [INIT] MTinitialize .. CPU Clock 500000000 Hz mips_counter_frequency:250000000 r4k_offset: 0x0003d090(250000) init_US_counter : time1 = 28 , time2 = 225062, diff 225034 US_counter = 112 set to constant US_counter = 112 cnt1 2039980 cnt2 2042567, diff 2587 cnt1 2886356 cnt2 2888155, diff 1799 Runtime code version: 00.96.803 System startup... [INIT] Memory COLOR 0, 10958496 bytes .. [INIT] Memory COLOR 1, 2097152 bytes .. [INIT] Memory COLOR 2, 13809456 bytes .. [INIT] Start Nand Init .. MXIC NAND 128MB 3,3V 8-bit found ----------------------------- NAND page size : 2048 NAND oob size : 64 NAND block size : 131072 NAND page/block : 64 NAND block/chip : 1024 NAND chip size : 0x8000000 NAND page shift : 11 NAND page mask : 0xFFFF NAND block shift : 17 ----------------------------- Scan BAD Block ... 0 Bad Block(s) console_enable=1 Boot Parameters found !!! Bootcode version: v2.01.07 Serial number: L504000130 Hardware version: R02 25.03.2015-19:35:49 [BUILD-WPA]: Key:47E0716F5AB4 [BUILD:PIN] PIN:L504000130, MAC:4C09D4A248E5 [BUILD-PIN]: PIN:49154290, len=8 [CONFIG] : default SSID = Orange-48E5 [CONFIG] : default WPA/WPA2 PSK = A5A56224 [BUILD:PIN] PIN:L504000130, MAC:4C09D4A248E5 [BUILD-PIN]: PIN:49154290, len=8 !![E-CFG-READ] Special Configuration data reading error!! !![E-CFG-READ] Reset to factory defaults 1!! nLen:98, Magic:0x33343536 my CFGVersionMagic = 33343536, old CFGVersionMagic on flash = 33343536 my CFGsize = 498848, my CFGDescSize = 42677 my Version = 00.96.803, Version on flash= 00.96.803 [CONFIG] old cfg version:[00.96.803], [0.0.96.0.803.100] source CFGsize = 498848, CFGDescSize = 42677 OldCfgHexSize:13782 Unzipping from 82602530 to 825F7E68 ... unzip_address sig 5d000080 pre, zipfile=0x82602530, unzipfile=0x825f7e68 unzip_address sig 8000005d end [ZIP 1] done Uncompressed size = 42675 Tail1 : END_III_Config_t Size of Old CFG_DESC is :42675!!! useCfgDesc:1 MyCfgHexSize:13782 Unzipping from 825F4878 to 825EA1B0 ... unzip_address sig 5d000080 pre, zipfile=0x825f4878, unzipfile=0x825ea1b0 unzip_address sig 8000005d end [ZIP 1] done Uncompressed size = 42675 My CFGDescSize:42677 useCfgDesc:1 Tail : END_III_Config_t useCfgDesc:3 Restore Config file from ver:00.96.803!!! [CONFIG] DS_Tail:[t_ARV7520CW22] [CONFIG] load_config ret=1 [updateConfig] flash version:[00.96.803], [0.0.96.0.803.100] [updateConfig] code version:[00.96.803], [0.0.96.0.803.100] [CONFIG] : smtp_email_from = Orange-48E5@orange.es !!! Invalid wireless channel range 0 ~ 255 !!! Use default value 1 ~ 13 default route: 0.0.0.0 [CheckUSBBackConf]Erase the garbage config in usbBackConf_s BufferInit: BUF_HDR_SZ=224 BUF_ALIGN_SZ=12 BUFFER_OFFSET=480 BUF_BUFSZ0=576 BUF_BUFSZ1=2304 NUM_OF_B0=0 NUM_OF_B1=4000 BUF_POOL0_SZ=0 BUF_POOL1_SZ=10112000 sizeof(BUFFER0)=800,sizeof(BUFFER1)=2528 *BUF0=0x83e29c28 *BUF1=0x83485008 Altgn *BUF0=0x83e29c40 *BUF1=0x83485020 End at BUF0:0x83e29c40, BUF1:0x83e29c20 BUF0[0]=0x83e29c40 BUF1[0]=0x83485020 buffer0 pointer init OK! buffer1 pointer init OK! [qm_lnk_init] CLOCKHZ=1000 ... [qm_lnk_init] add if 3 into QM link 0 [qm_lnk_init] add if 4 into QM link 0 [qm_cbq_enable] no QM attached [qm_cbq_detach] no QM is attached at link 0 pkt_avgsz=250, pkt_maxsz=1600, mtu=1600 f=10000000/100000, ns_per_byte=80000/1000 ptime=2000000000/1000, cptime=0/1000, offtime=0/1000 New cls: id=0, bw=80 ns/byte, maxd=0 ms, maxb=32, minb=2, avgpktsz=250, maxpktsz=1600, offtime=0, parent=0, borrow=0 pri=0, maxidle=31, minidle=-256, maxq=96, clsfg=17 pkt_avgsz=1600, pkt_maxsz=1600, mtu=1600 f=100000/100000, ns_per_byte=8000000/1000 ptime=18446744073709551615/1000, cptime=0/1000, offtime=0/1000 New cls: id=1, bw=8000 ns/byte, maxd=0 ms, maxb=16, minb=1, avgpktsz=1600, maxpktsz=1600, offtime=0, parent=8618ae70, borrow=8618ae70 pri=5, maxidle=200, minidle=-25600, maxq=48, clsfg=21 qm_cbq_attach(): cbqp->cbq_res=122 pkt_avgsz=250, pkt_maxsz=1600, mtu=1600 f=9900000/100000, ns_per_byte=80808/1000 ptime=2000000000/1000, cptime=0/1000, offtime=0/1000 New cls: id=2, bw=80 ns/byte, maxd=0 ms, maxb=32, minb=4, avgpktsz=250, maxpktsz=1600, offtime=0, parent=8618ae70, borrow=8618ae70 pri=5, maxidle=31, minidle=-258, maxq=48, clsfg=21 pkt_avgsz=250, pkt_maxsz=1600, mtu=1600 f=1/100000, ns_per_byte=4294967295/1000 [qm_cbq_newcls] warning: bandwidth of the class may be low enough to cause INT overflow ptime=2000000000/1000, cptime=18446744073709551615/1000, offtime=18446744073709551615/1000 New cls: id=3, bw=1342177 ns/byte, maxd=0 ms, maxb=16, minb=4, avgpktsz=250, maxpktsz=1600, offtime=1366279, parent=86189870, borrow=86189870 pri=6, maxidle=0, minidle=-4294966, maxq=48, clsfg=20 pkt_avgsz=250, pkt_maxsz=1600, mtu=1600 f=1/100000, ns_per_byte=4294967295/1000 [qm_cbq_newcls] warning: bandwidth of the class may be low enough to cause INT overflow ptime=2000000000/1000, cptime=18446744073709551615/1000, offtime=18446744073709551615/1000 New cls: id=4, bw=1342177 ns/byte, maxd=0 ms, maxb=16, minb=4, avgpktsz=250, maxpktsz=1600, offtime=1366279, parent=86189870, borrow=86189870 pri=0, maxidle=0, minidle=-4294966, maxq=96, clsfg=21 pkt_avgsz=250, pkt_maxsz=1600, mtu=1600 f=1/100000, ns_per_byte=4294967295/1000 [qm_cbq_newcls] warning: bandwidth of the class may be low enough to cause INT overflow ptime=2000000000/1000, cptime=18446744073709551615/1000, offtime=18446744073709551615/1000 New cls: id=5, bw=1342177 ns/byte, maxd=0 ms, maxb=16, minb=4, avgpktsz=250, maxpktsz=1600, offtime=1366279, parent=86189870, borrow=86189870 pri=1, maxidle=0, minidle=-4294966, maxq=48, clsfg=23 pkt_avgsz=250, pkt_maxsz=1600, mtu=1600 f=1/100000, ns_per_byte=4294967295/1000 [qm_cbq_newcls] warning: bandwidth of the class may be low enough to cause INT overflow ptime=2000000000/1000, cptime=18446744073709551615/1000, offtime=18446744073709551615/1000 New cls: id=6, bw=1342177 ns/byte, maxd=0 ms, maxb=16, minb=4, avgpktsz=250, maxpktsz=1600, offtime=1366279, parent=86189870, borrow=86189870 pri=2, maxidle=0, minidle=-4294966, maxq=48, clsfg=23 pkt_avgsz=250, pkt_maxsz=1600, mtu=1600 f=1/100000, ns_per_byte=4294967295/1000 [qm_cbq_newcls] warning: bandwidth of the class may be low enough to cause INT overflow ptime=2000000000/1000, cptime=18446744073709551615/1000, offtime=18446744073709551615/1000 New cls: id=7, bw=1342177 ns/byte, maxd=0 ms, maxb=16, minb=4, avgpktsz=250, maxpktsz=1600, offtime=1366279, parent=86189870, borrow=86189870 pri=3, maxidle=0, minidle=-4294966, maxq=48, clsfg=23 pkt_avgsz=250, pkt_maxsz=1600, mtu=1600 f=1/100000, ns_per_byte=4294967295/1000 [qm_cbq_newcls] warning: bandwidth of the class may be low enough to cause INT overflow ptime=2000000000/1000, cptime=18446744073709551615/1000, offtime=18446744073709551615/1000 New cls: id=8, bw=1342177 ns/byte, maxd=0 ms, maxb=16, minb=4, avgpktsz=250, maxpktsz=1600, offtime=1366279, parent=86189870, borrow=86189870 pri=4, maxidle=0, minidle=-4294966, maxq=48, clsfg=23 pkt_avgsz=250, pkt_maxsz=1600, mtu=1600 f=9900000/100000, ns_per_byte=80808/1000 ptime=2000000000/1000, cptime=0/1000, offtime=0/1000 New cls: id=9, bw=80 ns/byte, maxd=0 ms, maxb=16, minb=4, avgpktsz=250, maxpktsz=1600, offtime=0, parent=86189870, borrow=86189870 pri=6, maxidle=31, minidle=-258, maxq=48, clsfg=20 [qm_cbq_reset_dstcp_ctrl] dstcp_ctrl_fg=0x1, dstcp_pkt_delay=13 ms, dstcp_max_burst=6056 bytes CLOCKHZ=1000 gConfig.Interface[0].IP_Addr = 127.0.0.1 gConfig.Interface[0].Subnet_Mask = 255.255.255.255 gConfig.Interface[0].Description = LOCAL_LOOPBACK gConfig.Interface[0].Framing = ***** [iput_IpLinkUp] ifno=0, link_type:12 Interface 0 ip = 127.0.0.1 gConfig.Interface[1].IP_Addr = 192.168.1.1 gConfig.Interface[1].Subnet_Mask = 255.255.255.0 gConfig.Interface[1].Description = LAN1 gConfig.Interface[1].Framing = gConfig.Interface[1].VLAN_Idx = 0 ifp->ipaddr = C0A80101 ifp->netmask = FFFFFF00 gConfig.Vlan_Ports[gConfig.Interface[1].VLAN_Idx].VNet = 1 gConfig.Vlan_Ports[gConfig.Interface[1].VLAN_Idx].IGMP_Querier_Enable = 0 [IfInit] ifno=1, gConfig.Interface[1].vlan_tagged=0, line 693 br_register_static_mcast_mac: Add static entry 01:00:5E:00:00:01 to VLAN 0 (port 1) br_register_static_mcast_mac: Add static entry 01:00:5E:00:00:01 to VLAN 0 (port 2) br_register_static_mcast_mac: Add static entry 01:00:5E:00:00:02 to VLAN 0 (port 1) br_register_static_mcast_mac: Add static entry 01:00:5E:00:00:02 to VLAN 0 (port 2) br_register_static_mcast_mac: Add static entry 01:00:5E:00:00:16 to VLAN 0 (port 1) br_register_static_mcast_mac: Add static entry 01:00:5E:00:00:16 to VLAN 0 (port 2) br_register_static_mcast_mac: Add static entry 01:00:5E:7F:FF:FA to VLAN 0 (port 1) br_register_static_mcast_mac: Add static entry 01:00:5E:7F:FF:FA to VLAN 0 (port 2) [mac_0_init] ifno=1, vlan=0, vid=1, port_mask=0xf, mac_0_initialized=0 [KERN_INFO]IFX PMU driver, version 1.0.5, (c)2009 Infineon Technologies AG ifx_dma_init_module : ifx_pmu_set: PMU_PWDCR0 = 0xc615929f module 5 regid 0 regbit 5 ifx_pmu_set: Actual enabling.......... 1 ifx_pmu_set: Module DMA has been activated 1 times before [map_dma_chan 1618]: dma_chan[0] request_irq 64 IrqConnect : IRQ = 64, Handler = 0x805175B4 [map_dma_chan 1618]: dma_chan[1] request_irq 65 IrqConnect : IRQ = 65, Handler = 0x805175B4 [map_dma_chan 1618]: dma_chan[2] request_irq 66 IrqConnect : IRQ = 66, Handler = 0x805175B4 [map_dma_chan 1618]: dma_chan[3] request_irq 67 IrqConnect : IRQ = 67, Handler = 0x805175B4 [map_dma_chan 1618]: dma_chan[4] request_irq 68 IrqConnect : IRQ = 68, Handler = 0x805175B4 [map_dma_chan 1618]: dma_chan[5] request_irq 69 IrqConnect : IRQ = 69, Handler = 0x805175B4 [map_dma_chan 1618]: dma_chan[6] request_irq 70 IrqConnect : IRQ = 70, Handler = 0x805175B4 [map_dma_chan 1618]: dma_chan[7] request_irq 71 IrqConnect : IRQ = 71, Handler = 0x805175B4 [map_dma_chan 1618]: dma_chan[8] request_irq 72 IrqConnect : IRQ = 72, Handler = 0x805175B4 [map_dma_chan 1618]: dma_chan[9] request_irq 73 IrqConnect : IRQ = 73, Handler = 0x805175B4 [map_dma_chan 1618]: dma_chan[10] request_irq 74 IrqConnect : IRQ = 74, Handler = 0x805175B4 [map_dma_chan 1618]: dma_chan[11] request_irq 75 IrqConnect : IRQ = 75, Handler = 0x805175B4 [map_dma_chan 1618]: dma_chan[12] request_irq 89 IrqConnect : IRQ = 89, Handler = 0x805175B4 [map_dma_chan 1618]: dma_chan[13] request_irq 90 IrqConnect : IRQ = 90, Handler = 0x805175B4 [map_dma_chan 1618]: dma_chan[14] request_irq 91 IrqConnect : IRQ = 91, Handler = 0x805175B4 [map_dma_chan 1618]: dma_chan[15] request_irq 92 IrqConnect : IRQ = 92, Handler = 0x805175B4 [map_dma_chan 1618]: dma_chan[16] request_irq 93 IrqConnect : IRQ = 93, Handler = 0x805175B4 [map_dma_chan 1618]: dma_chan[17] request_irq 62 IrqConnect : IRQ = 62, Handler = 0x805175B4 [map_dma_chan 1618]: dma_chan[18] request_irq 80 IrqConnect : IRQ = 80, Handler = 0x805175B4 [map_dma_chan 1618]: dma_chan[19] request_irq 85 IrqConnect : IRQ = 85, Handler = 0x805175B4 [map_dma_chan 1618]: dma_chan[20] request_irq 128 IrqConnect : IRQ = 128, Handler = 0x805175B4 [map_dma_chan 1618]: dma_chan[21] request_irq 129 IrqConnect : IRQ = 129, Handler = 0x805175B4 [map_dma_chan 1618]: dma_chan[22] request_irq 130 IrqConnect : IRQ = 130, Handler = 0x805175B4 [map_dma_chan 1618]: dma_chan[23] request_irq 131 IrqConnect : IRQ = 131, Handler = 0x805175B4 [map_dma_chan 1618]: dma_chan[24] request_irq 132 IrqConnect : IRQ = 132, Handler = 0x805175B4 [map_dma_chan 1618]: dma_chan[25] request_irq 133 IrqConnect : IRQ = 133, Handler = 0x805175B4 [map_dma_chan 1618]: dma_chan[26] request_irq 134 IrqConnect : IRQ = 134, Handler = 0x805175B4 [map_dma_chan 1618]: dma_chan[27] request_irq 135 IrqConnect : IRQ = 135, Handler = 0x805175B4 ifx_dma_init_module : g_desc_list 81902680 [KERN_INFO]IFX DMA driver, version ifxmips_dma_core.c:v1.0.4 ,(c)2009 Infineon Technologies AG [KERN_INFO]Infineon Technologies RCU driver version 1.1.2 vr9_config_mdio_gpio !!! [vr9_config_mdio_gpio] *IFX_GPIO_P2_ALTSEL0=0xc00, IFX_GPIO_P2_ALTSEL1=0x0, *IFX_GPIO_P2_DIR=0xc03, *IFX_GPIO_P2_OD=0xc03 IFX SWITCH API, Version 1.1.6.7 IFX_ETHSW_Open() !!! [KERN_INFO]SWAPI: Registered character device [switch_api] with major no [81] ifx_pmu_set: PMU_PWDCR0 = 0xc615929f module 29 regid 0 regbit 29 ifx_pmu_set: Actual enabling.......... 1 ifx_pmu_set: Module PPE-TOP has been activated 1 times before ifx_pmu_set: PMU_PWDCR0 = 0xc615929f module 23 regid 0 regbit 23 ifx_pmu_set: Actual enabling.......... 1 ifx_pmu_set: Module PPE-DPLUSM has been activated 1 times before ifx_pmu_set: PMU_PWDCR0 = 0xc615929f module 24 regid 0 regbit 24 ifx_pmu_set: Actual enabling.......... 1 ifx_pmu_set: Module PPE-DPLUSS has been activated 1 times before ifx_pmu_set: PMU_PWDCR0 = 0xc615929f module 28 regid 0 regbit 28 ifx_pmu_set: Actual enabling.......... 1 ifx_pmu_set: Module SWITCH has been activated 1 times before Switch API: PCE MicroCode loaded !! IFX_ETHSW_IOCTL_WrapperInit() !!! chip_id 2000b713 chip_id b Switch Auto Polling value = 0 [KERN_ERR ] GPHY FW load for A2x !! [fix_switch_power_saving_for_cpu1_2:1042] Ethernet IOP turn-off patch [KERN_INFO] IFX GPHY driver FE Mode, version ifxmips_vr9_gphy: V0.9 - Firmware: 4406 [amazon_s_eth_init] Loading A5 (MII0/1 + ATM) driver ...... [amazon_s_eth_init] gPPE_Start_Module=0x1, gPPE_HAL_Start_Module=0x0 ifx_pmu_set: PMU_PWDCR0 = 0x8615909f module 9 regid 0 regbit 9 ifx_pmu_set: Actual enabling.......... 1 ifx_pmu_set: Module DSL-DFE has been activated 1 times before ifx_pmu_set: PMU_PWDCR0 = 0x8615909f module 13 regid 0 regbit 13 ifx_pmu_set: Actual enabling.......... 1 ifx_pmu_set: Module AHBS has been activated 1 times before ifx_pmu_set: PMU_PWDCR0 = 0x8615909f module 19 regid 0 regbit 19 ifx_pmu_set: Actual enabling.......... 1 ifx_pmu_set: Module PPE-SSL01 has been activated 1 times before ifx_pmu_set: PMU_PWDCR0 = 0x8615909f module 21 regid 0 regbit 21 ifx_pmu_set: Actual enabling.......... 1 ifx_pmu_set: Module PPE-TC has been activated 1 times before ifx_pmu_set: PMU_PWDCR0 = 0x8615909f module 22 regid 0 regbit 22 ifx_pmu_set: Actual enabling.......... 1 ifx_pmu_set: Module PPE-EMA has been activated 1 times before ifx_pmu_set: PMU_PWDCR0 = 0x8615909f module 23 regid 0 regbit 23 ifx_pmu_set: Module PPE-DPLUSM has been activated 2 times before ifx_pmu_set: PMU_PWDCR0 = 0x8615909f module 24 regid 0 regbit 24 ifx_pmu_set: Module PPE-DPLUSS has been activated 2 times before ifx_pmu_set: PMU_PWDCR0 = 0x8615909f module 28 regid 0 regbit 28 ifx_pmu_set: Module SWITCH has been activated 3 times before ifx_pmu_set: PMU_PWDCR0 = 0x8615909f module 29 regid 0 regbit 29 ifx_pmu_set: Module PPE-TOP has been activated 2 times before ifx_pmu_set: PMU_PWDCR0 = 0x8611909f module 18 regid 0 regbit 18 ifx_pmu_set: Actual enabling.......... 1 ifx_pmu_set: Module PPE-QSB has been activated 1 times before [a5 alloc_dma] pre_alloc_desc_total_num=704, line 6168 [turn_on_dma_rx] a5, line 4549 [turn_on_dma_rx] a5, line 4549 IrqConnect : IRQ = 87, Handler = 0x80540F3C IrqConnect : IRQ = 88, Handler = 0x80541098 Succeeded! PPE datapath driver info: Version ID: 64.3.7.1.0.1.4 Family : VR9 DR Type : Normal Data Path | Indirect-Fast Path Interface : MII0 | MII1 | ATM Mode : Routing Release : 0.1.4 PPE firmware info: Version ID: 7.2.4.6.1.17 Family : VR9 FW Type : Acceleration Interface : MII0/1 + ATM Mode : Bridging + IPv4 Routing Release : 1.17 [switch_utility] cmd=Enable [switch_utility] switch_utility, Enable, [switch_utility] cmd=CfgSet 3 1 1542 0 00:00:00:00:00:00 [switch_utility] switch_utility, CfgSet, 3, 1, 1542, 0, 00:00:00:00:00:00, [switch_utility] cmd=RegisterSet 0x453 0x0 [switch_utility] switch_utility, RegisterSet, 0x453, 0x0, [switch_utility] cmd=RegisterSet 0x454 0x07f [switch_utility] switch_utility, RegisterSet, 0x454, 0x07f, [switch_utility] cmd=RegisterSet 0x455 0x07f [switch_utility] switch_utility, RegisterSet, 0x455, 0x07f, [switch_utility] cmd=RegisterSet 0xc4B 0x3F [switch_utility] switch_utility, RegisterSet, 0xc4B, 0x3F, [switch_utility] cmd=RegisterSet 0xc4C 0x105 [switch_utility] switch_utility, RegisterSet, 0xc4C, 0x105, [switch_utility] cmd=RegisterSet 0xc55 0x1800 [switch_utility] switch_utility, RegisterSet, 0xc55, 0x1800, [switch_utility] cmd=RegisterSet 0xc54 0x1801 [switch_utility] switch_utility, RegisterSet, 0xc54, 0x1801, [switch_utility] cmd=RegisterSet 0xc53 0x1811 [switch_utility] switch_utility, RegisterSet, 0xc53, 0x1811, [switch_utility] cmd=RegisterSet 0xC52 0x1812 [switch_utility] switch_utility, RegisterSet, 0xC52, 0x1812, [switch_utility] cmd=RegisterSet 0xc51 0x1813 [switch_utility] switch_utility, RegisterSet, 0xc51, 0x1813, [switch_utility] cmd=RegisterSet 0xC50 0x1814 [switch_utility] switch_utility, RegisterSet, 0xC50, 0x1814, [switch_utility] cmd=RegisterSet 0x903 0x180 [switch_utility] switch_utility, RegisterSet, 0x903, 0x180, [switch_utility] cmd=RegisterSet 0x90F 0x180 [switch_utility] switch_utility, RegisterSet, 0x90F, 0x180, [switch_utility] cmd=RegisterSet 0x93F 0x180 [switch_utility] switch_utility, RegisterSet, 0x93F, 0x180, [switch_utility] cmd=RegisterSet 0x91B 0x180 [switch_utility] switch_utility, RegisterSet, 0x91B, 0x180, [switch_utility] cmd=RegisterSet 0x933 0x180 [switch_utility] switch_utility, RegisterSet, 0x933, 0x180, [switch_utility] cmd=RegisterSet 0x927 0x180 [switch_utility] switch_utility, RegisterSet, 0x927, 0x180, [switch_utility] cmd=RegisterSet 0x94B 0x180 [switch_utility] switch_utility, RegisterSet, 0x94B, 0x180, [switch_utility] cmd=PortLinkCfgSet 0 0 0 0 1000 0 0 3 0 0 [switch_utility] switch_utility, PortLinkCfgSet, 0, 0, 0, 0, 1000, 0, 0, 3, 0, 0, [switch_utility] cmd=PortLinkCfgSet 1 0 0 0 1000 0 0 3 0 0 [switch_utility] switch_utility, PortLinkCfgSet, 1, 0, 0, 0, 1000, 0, 0, 3, 0, 0, [switch_utility] cmd=PortLinkCfgSet 5 0 0 0 100 0 0 0 1 0 [switch_utility] switch_utility, PortLinkCfgSet, 5, 0, 0, 0, 100, 0, 0, 0, 1, 0, [switch_utility] cmd=PortLinkCfgSet 2 0 0 0 100 0 0 0 1 0 [switch_utility] switch_utility, PortLinkCfgSet, 2, 0, 0, 0, 100, 0, 0, 0, 1, 0, [switch_utility] cmd=PortLinkCfgSet 3 0 0 0 100 0 0 0 1 0 [switch_utility] switch_utility, PortLinkCfgSet, 3, 0, 0, 0, 100, 0, 0, 0, 1, 0, [switch_utility] cmd=PortLinkCfgSet 4 0 0 0 100 0 0 0 1 0 [switch_utility] switch_utility, PortLinkCfgSet, 4, 0, 0, 0, 100, 0, 0, 0, 1, 0, [switch_utility] cmd=RegisterSet 0xc77 0xc001 [switch_utility] switch_utility, RegisterSet, 0xc77, 0xc001, [switch_utility] cmd=RegisterSet 0xc79 0xc001 [switch_utility] switch_utility, RegisterSet, 0xc79, 0xc001, [switch_utility] cmd=RegisterSet 0xc81 0xc001 [switch_utility] switch_utility, RegisterSet, 0xc81, 0xc001, [switch_utility] cmd=RegisterSet 0x91C 0x0B [switch_utility] switch_utility, RegisterSet, 0x91C, 0x0B, [switch_utility] cmd=RegisterSet 0x934 0x0B [switch_utility] switch_utility, RegisterSet, 0x934, 0x0B, [switch_utility] cmd=RegisterSet 0x928 0x0B [switch_utility] switch_utility, RegisterSet, 0x928, 0x0B, [switch_utility] cmd=RegisterSet 0x940 0x0B [switch_utility] switch_utility, RegisterSet, 0x940, 0x0B, [switch_utility] cmd=MDIO_DataWrite 0x11 0x4 0x5e1 [switch_utility] switch_utility, MDIO_DataWrite, 0x11, 0x4, 0x5e1, [switch_utility] cmd=MDIO_DataWrite 0x13 0x4 0x5e1 [switch_utility] switch_utility, MDIO_DataWrite, 0x13, 0x4, 0x5e1, [switch_utility] cmd=MDIO_DataWrite 0x0 0x4 0x5e1 [switch_utility] switch_utility, MDIO_DataWrite, 0x0, 0x4, 0x5e1, [switch_utility] cmd=MDIO_DataWrite 0x12 0x4 0x5e1 [switch_utility] switch_utility, MDIO_DataWrite, 0x12, 0x4, 0x5e1, [switch_utility] cmd=MDIO_DataWrite 0x14 0x4 0x5e1 [switch_utility] switch_utility, MDIO_DataWrite, 0x14, 0x4, 0x5e1, [switch_utility] cmd=RegisterSet 0x4A 0x51C [switch_utility] switch_utility, RegisterSet, 0x4A, 0x51C, [switch_enable_igmp_snooping] gSetting.IGMP_Snooping=1 [switch_utility] cmd=MulticastRouterPortAdd 6 [switch_utility] switch_utility, MulticastRouterPortAdd, 6, [switch_utility] cmd=MulticastSnoopCfgSet 2 1 0 3 6 1 3 100 2 1 1 [switch_utility] switch_utility, MulticastSnoopCfgSet, 2, 1, 0, 3, 6, 1, 3, 100, 2, 1, 1, [switch_utility] cmd=MulticastTableEntryAdd 4 0 224.0.0.1 0.0.0.0 2 [switch_utility] switch_utility, MulticastTableEntryAdd, 4, 0, 224.0.0.1, 0.0.0.0, 2, [switch_utility] cmd=MulticastTableEntryAdd 5 0 224.0.0.1 0.0.0.0 2 [switch_utility] switch_utility, MulticastTableEntryAdd, 5, 0, 224.0.0.1, 0.0.0.0, 2, [switch_utility] cmd=MulticastTableEntryAdd 2 0 224.0.0.1 0.0.0.0 2 [switch_utility] switch_utility, MulticastTableEntryAdd, 2, 0, 224.0.0.1, 0.0.0.0, 2, [switch_utility] cmd=MulticastTableEntryAdd 3 0 224.0.0.1 0.0.0.0 2 [switch_utility] switch_utility, MulticastTableEntryAdd, 3, 0, 224.0.0.1, 0.0.0.0, 2, [switch_utility] cmd=MulticastTableEntryAdd 0 0 224.0.0.1 0.0.0.0 2 [switch_utility] switch_utility, MulticastTableEntryAdd, 0, 0, 224.0.0.1, 0.0.0.0, 2, [switch_utility] cmd=MulticastTableEntryAdd 6 0 224.0.0.1 0.0.0.0 2 [switch_utility] switch_utility, MulticastTableEntryAdd, 6, 0, 224.0.0.1, 0.0.0.0, 2, [switch_utility] cmd=MulticastTableEntryAdd 4 0 224.0.0.2 0.0.0.0 2 [switch_utility] switch_utility, MulticastTableEntryAdd, 4, 0, 224.0.0.2, 0.0.0.0, 2, [switch_utility] cmd=MulticastTableEntryAdd 5 0 224.0.0.2 0.0.0.0 2 [switch_utility] switch_utility, MulticastTableEntryAdd, 5, 0, 224.0.0.2, 0.0.0.0, 2, [switch_utility] cmd=MulticastTableEntryAdd 2 0 224.0.0.2 0.0.0.0 2 [switch_utility] switch_utility, MulticastTableEntryAdd, 2, 0, 224.0.0.2, 0.0.0.0, 2, [switch_utility] cmd=MulticastTableEntryAdd 3 0 224.0.0.2 0.0.0.0 2 [switch_utility] switch_utility, MulticastTableEntryAdd, 3, 0, 224.0.0.2, 0.0.0.0, 2, [switch_utility] cmd=MulticastTableEntryAdd 0 0 224.0.0.2 0.0.0.0 2 [switch_utility] switch_utility, MulticastTableEntryAdd, 0, 0, 224.0.0.2, 0.0.0.0, 2, [switch_utility] cmd=MulticastTableEntryAdd 6 0 224.0.0.2 0.0.0.0 2 [switch_utility] switch_utility, MulticastTableEntryAdd, 6, 0, 224.0.0.2, 0.0.0.0, 2, [switch_utility] cmd=MulticastTableEntryAdd 4 0 224.0.0.22 0.0.0.0 2 [switch_utility] switch_utility, MulticastTableEntryAdd, 4, 0, 224.0.0.22, 0.0.0.0, 2, [switch_utility] cmd=MulticastTableEntryAdd 5 0 224.0.0.22 0.0.0.0 2 [switch_utility] switch_utility, MulticastTableEntryAdd, 5, 0, 224.0.0.22, 0.0.0.0, 2, [switch_utility] cmd=MulticastTableEntryAdd 2 0 224.0.0.22 0.0.0.0 2 [switch_utility] switch_utility, MulticastTableEntryAdd, 2, 0, 224.0.0.22, 0.0.0.0, 2, [switch_utility] cmd=MulticastTableEntryAdd 3 0 224.0.0.22 0.0.0.0 2 [switch_utility] switch_utility, MulticastTableEntryAdd, 3, 0, 224.0.0.22, 0.0.0.0, 2, [switch_utility] cmd=MulticastTableEntryAdd 0 0 224.0.0.22 0.0.0.0 2 [switch_utility] switch_utility, MulticastTableEntryAdd, 0, 0, 224.0.0.22, 0.0.0.0, 2, [switch_utility] cmd=MulticastTableEntryAdd 6 0 224.0.0.22 0.0.0.0 2 [switch_utility] switch_utility, MulticastTableEntryAdd, 6, 0, 224.0.0.22, 0.0.0.0, 2, [switch_utility] cmd=MulticastTableEntryAdd 4 0 239.255.255.250 0.0.0.0 2 [switch_utility] switch_utility, MulticastTableEntryAdd, 4, 0, 239.255.255.250, 0.0.0.0, 2, [switch_utility] cmd=MulticastTableEntryAdd 5 0 239.255.255.250 0.0.0.0 2 [switch_utility] switch_utility, MulticastTableEntryAdd, 5, 0, 239.255.255.250, 0.0.0.0, 2, [switch_utility] cmd=MulticastTableEntryAdd 2 0 239.255.255.250 0.0.0.0 2 [switch_utility] switch_utility, MulticastTableEntryAdd, 2, 0, 239.255.255.250, 0.0.0.0, 2, [switch_utility] cmd=MulticastTableEntryAdd 3 0 239.255.255.250 0.0.0.0 2 [switch_utility] switch_utility, MulticastTableEntryAdd, 3, 0, 239.255.255.250, 0.0.0.0, 2, [switch_utility] cmd=MulticastTableEntryAdd 0 0 239.255.255.250 0.0.0.0 2 [switch_utility] switch_utility, MulticastTableEntryAdd, 0, 0, 239.255.255.250, 0.0.0.0, 2, [switch_utility] cmd=MulticastTableEntryAdd 6 0 239.255.255.250 0.0.0.0 2 [switch_utility] switch_utility, MulticastTableEntryAdd, 6, 0, 239.255.255.250, 0.0.0.0, 2, [switch_utility] cmd=PCE_RuleDelete 50 [switch_utility] switch_utility, PCE_RuleDelete, 50, [switch_utility] cmd=PCE_RuleDelete 51 [switch_utility] switch_utility, PCE_RuleDelete, 51, [switch_utility] cmd=PCE_RuleDelete 52 [switch_utility] switch_utility, PCE_RuleDelete, 52, [switch_utility] cmd=PCE_RuleDelete 53 [switch_utility] switch_utility, PCE_RuleDelete, 53, [switch_utility] cmd=PCE_RuleDelete 54 [switch_utility] switch_utility, PCE_RuleDelete, 54, [switch_utility] cmd=PCE_RuleDelete 55 [switch_utility] switch_utility, PCE_RuleDelete, 55, [switch_utility] cmd=PCE_RuleWrite 9 1 1 6 0 0 0 0 0 0 0 0 00:00:00:00:00:00 0 0 00:00:00:00:00:00 0 0 0 0 0 0 0 0 0 0 0.0.0.0 0 0 0.0.0.0 0 1 2048 0 1 2 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0 0 0 0 0 0 [switch_utility] switch_utility, PCE_RuleWrite, 9, 1, 1, 6, 0, 0, 0, 0, 0, 0, 0, 0, 00:00:00:00:00:00, 0, 0, 00:00:00:00:00:00, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0.0.0.0, 0, 0, 0.0.0.0, 0, 1, 2048, 0, 1, 2, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, [switch_utility] cmd=PCE_RuleWrite 10 1 0 0 0 0 0 0 0 0 0 0 00:00:00:00:00:00 0x0 0 00:00:00:00:00:00 0x0 1 4608 1 3 0 0 0 0 0 000.000.000.000 0x0 0 000.000.000.000 0x0 1 2048 0x0 1 2 0x0 0 0 0 0 1 1 0 0 0 0 0 0 4 64 0 0 0 0 0 0 0 0 0 0 0 [switch_utility] switch_utility, PCE_RuleWrite, 10, 1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 00:00:00:00:00:00, 0x0, 0, 00:00:00:00:00:00, 0x0, 1, 4608, 1, 3, 0, 0, 0, 0, 0, 000.000.000.000, 0x0, 0, 000.000.000.000, 0x0, 1, 2048, 0x0, 1, 2, 0x0, 0, 0, 0, 0, 1, 1, 0, 0, 0, 0, 0, 0, 4, 64, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, [switch_utility] cmd=PCE_RuleWrite 11 1 0 0 0 0 0 0 0 0 0 0 00:00:00:00:00:00 0x0 0 00:00:00:00:00:00 0x0 1 4864 1 3 0 0 0 0 0 000.000.000.000 0x0 0 000.000.000.000 0x0 1 2048 0x0 1 2 0x0 0 0 0 0 1 1 0 0 0 0 0 0 4 64 0 0 0 0 0 0 0 0 0 0 0 [switch_utility] switch_utility, PCE_RuleWrite, 11, 1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 00:00:00:00:00:00, 0x0, 0, 00:00:00:00:00:00, 0x0, 1, 4864, 1, 3, 0, 0, 0, 0, 0, 000.000.000.000, 0x0, 0, 000.000.000.000, 0x0, 1, 2048, 0x0, 1, 2, 0x0, 0, 0, 0, 0, 1, 1, 0, 0, 0, 0, 0, 0, 4, 64, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, [switch_utility] cmd=PCE_RuleWrite 12 1 0 0 0 0 0 0 0 0 0 0 00:00:00:00:00:00 0x0 0 00:00:00:00:00:00 0x0 1 5632 1 3 0 0 0 0 0 000.000.000.000 0x0 0 000.000.000.000 0x0 1 2048 0x0 1 2 0x0 0 0 0 0 1 1 0 0 0 0 0 0 4 64 0 0 0 0 0 0 0 0 0 0 0 [switch_utility] switch_utility, PCE_RuleWrite, 12, 1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 00:00:00:00:00:00, 0x0, 0, 00:00:00:00:00:00, 0x0, 1, 5632, 1, 3, 0, 0, 0, 0, 0, 000.000.000.000, 0x0, 0, 000.000.000.000, 0x0, 1, 2048, 0x0, 1, 2, 0x0, 0, 0, 0, 0, 1, 1, 0, 0, 0, 0, 0, 0, 4, 64, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, [switch_utility] cmd=PCE_RuleWrite 13 1 0 0 0 0 0 0 0 0 0 0 00:00:00:00:00:00 0x0 0 00:00:00:00:00:00 0x0 1 5888 1 3 0 0 0 0 0 000.000.000.000 0x0 0 000.000.000.000 0x0 1 2048 0x0 1 2 0x0 0 0 0 0 1 1 0 0 0 0 0 0 4 64 0 0 0 0 0 0 0 0 0 0 0 [switch_utility] switch_utility, PCE_RuleWrite, 13, 1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 00:00:00:00:00:00, 0x0, 0, 00:00:00:00:00:00, 0x0, 1, 5888, 1, 3, 0, 0, 0, 0, 0, 000.000.000.000, 0x0, 0, 000.000.000.000, 0x0, 1, 2048, 0x0, 1, 2, 0x0, 0, 0, 0, 0, 1, 1, 0, 0, 0, 0, 0, 0, 4, 64, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, [switch_utility] cmd=PCE_RuleWrite 14 1 0 0 0 0 0 0 0 0 0 0 00:00:00:00:00:00 0x0 0 00:00:00:00:00:00 0x0 1 8704 1 3 0 0 0 0 0 000.000.000.000 0x0 0 000.000.000.000 0x0 1 2048 0x0 1 2 0x0 0 0 0 0 1 1 0 0 0 0 0 0 4 64 0 0 0 0 0 0 0 0 0 0 0 [switch_utility] switch_utility, PCE_RuleWrite, 14, 1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 00:00:00:00:00:00, 0x0, 0, 00:00:00:00:00:00, 0x0, 1, 8704, 1, 3, 0, 0, 0, 0, 0, 000.000.000.000, 0x0, 0, 000.000.000.000, 0x0, 1, 2048, 0x0, 1, 2, 0x0, 0, 0, 0, 0, 1, 1, 0, 0, 0, 0, 0, 0, 4, 64, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, [switch_utility] cmd=PCE_RuleWrite 15 1 0 0 0 0 0 0 0 0 0 0 00:00:00:00:00:00 0x0 0 00:00:00:00:00:00 0x0 1 4352 1 3 0 0 0 0 0 000.000.000.000 0x0 0 000.000.000.000 0x0 1 2048 0x0 1 2 0x0 0 0 0 0 1 1 0 0 0 0 0 0 4 64 0 0 0 0 0 0 0 0 0 0 0 [switch_utility] switch_utility, PCE_RuleWrite, 15, 1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 00:00:00:00:00:00, 0x0, 0, 00:00:00:00:00:00, 0x0, 1, 4352, 1, 3, 0, 0, 0, 0, 0, 000.000.000.000, 0x0, 0, 000.000.000.000, 0x0, 1, 2048, 0x0, 1, 2, 0x0, 0, 0, 0, 0, 1, 1, 0, 0, 0, 0, 0, 0, 4, 64, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, [mac_0_init] VLAN port: 0x000f, ifCount=1 [mac_0_init] ------->add port 4 to vlan 1 [mac_0_init] ------->add port 5 to vlan 1 [mac_0_init] ------->add port 2 to vlan 1 [mac_0_init] ------->add port 3 to vlan 1 [config_SW_VLAN] bTaggedIngress=0, bTaggedEgress=0 [switch_utility] cmd=VLAN_IdCreate 50 1 [switch_utility] switch_utility, VLAN_IdCreate, 50, 1, [switch_utility] cmd=VLAN_PortCfgSet 6 50 0 0 3 0 0 [switch_utility] switch_utility, VLAN_PortCfgSet, 6, 50, 0, 0, 3, 0, 0, [switch_utility] cmd=VLAN_IdCreate 1 1 [switch_utility] switch_utility, VLAN_IdCreate, 1, 1, [switch_utility] cmd=VLAN_PortCfgSet 2 1 0 0 3 0 0 [switch_utility] switch_utility, VLAN_PortCfgSet, 2, 1, 0, 0, 3, 0, 0, [switch_utility] cmd=VLAN_PortCfgSet 3 1 0 0 3 0 0 [switch_utility] switch_utility, VLAN_PortCfgSet, 3, 1, 0, 0, 3, 0, 0, [switch_utility] cmd=VLAN_PortCfgSet 4 1 0 0 3 0 0 [switch_utility] switch_utility, VLAN_PortCfgSet, 4, 1, 0, 0, 3, 0, 0, [switch_utility] cmd=VLAN_PortCfgSet 5 1 0 0 3 0 0 [switch_utility] switch_utility, VLAN_PortCfgSet, 5, 1, 0, 0, 3, 0, 0, [switch_utility] cmd=VLAN_PortMemberAdd 1 2 0 [switch_utility] switch_utility, VLAN_PortMemberAdd, 1, 2, 0, [switch_utility] cmd=VLAN_PortMemberAdd 1 3 0 [switch_utility] switch_utility, VLAN_PortMemberAdd, 1, 3, 0, [switch_utility] cmd=VLAN_PortMemberAdd 1 4 0 [switch_utility] switch_utility, VLAN_PortMemberAdd, 1, 4, 0, [switch_utility] cmd=VLAN_PortMemberAdd 1 5 0 [switch_utility] switch_utility, VLAN_PortMemberAdd, 1, 5, 0, [switch_utility] cmd=VLAN_PortMemberAdd 1 6 1 [switch_utility] switch_utility, VLAN_PortMemberAdd, 1, 6, 1, mac_0_init: interface 1 registered to VLAN 1, port_mask=f MAC Address(ifno 1): 4c:09:d4:a2:48:e6 ***** [iput_IpLinkUp] ifno=1, link_type:12 br_MacAddress=4C-09-D4-A2-48-E6 Interface 1 ip = 192.168.1.1 gConfig.Interface[2].IP_Addr = 0.0.0.0 gConfig.Interface[2].Subnet_Mask = 0.0.0.0 gConfig.Interface[2].Description = WLAN gConfig.Interface[2].Framing = gConfig.Interface[2].VLAN_Idx = 0 ifp->ipaddr = C0A80101 ifp->netmask = FFFFFF00 gConfig.Vlan_Ports[gConfig.Interface[2].VLAN_Idx].VNet = 1 gConfig.Vlan_Ports[gConfig.Interface[2].VLAN_Idx].IGMP_Querier_Enable = 0 [IfInit] ifno=2, gConfig.Interface[2].vlan_tagged=0, line 693 hwlan_init(451): [HWLAN] ifno=2 irno=7 port=0x00000000 [hwlan_init] if_table[2]::4c-09-d4-a2-48-e6 ***** [iput_IpLinkUp] ifno=2, link_type:12 Interface 2 ip = 192.168.1.1 gConfig.Interface[3].IP_Addr = 0.0.0.0 gConfig.Interface[3].Subnet_Mask = 0.0.0.0 gConfig.Interface[3].Description = ATM1 gConfig.Interface[3].Framing = AAL5 [IfInit] ifno=3, gConfig.Interface[3].vlan_tagged=0, line 693 [sar_0_init] ifno=3, T_WAN_INT=3, sar_init=0, g_atm_priv_data.max_connections=15 ATM_UBR [ppe_open] g_atm_priv_data.connection_table=0 [turn_on_dma_rx] a5, line 4549 [ppe_open] (8.32): conn = 0, f_enable_irq=1 [sar_0_init] index=0, ifno=3, f_llc=1 [mpoa_setup] mpoa_type=0, f_llc=1 [sar_0_init] Init SAR ifno:3, vlan_tagged=0, g_atm_vcc[0] CONN:0 VPI/VCI:8/32 PORT:0 [sar_0_init] sar ifno: 3, flag: 0x00000200, up, sar_init=0 MAC Address: 4c:09:d4:a2:48:e5 [switch_utility] cmd=VLAN_IdCreate 2 2 [switch_utility] switch_utility, VLAN_IdCreate, 2, 2, [switch_utility] cmd=VLAN_IdCreate 20 2 [switch_utility] switch_utility, VLAN_IdCreate, 20, 2, [switch_utility] cmd=VLAN_PortCfgSet 11 2 0 0 3 0 1 [switch_utility] switch_utility, VLAN_PortCfgSet, 11, 2, 0, 0, 3, 0, 1, [switch_utility] cmd=VLAN_PortCfgSet 10 20 0 0 3 0 1 [switch_utility] switch_utility, VLAN_PortCfgSet, 10, 20, 0, 0, 3, 0, 1, [switch_utility] cmd=VLAN_PortMemberAdd 2 11 0 [switch_utility] switch_utility, VLAN_PortMemberAdd, 2, 11, 0, [switch_utility] cmd=VLAN_PortMemberAdd 20 10 0 [switch_utility] switch_utility, VLAN_PortMemberAdd, 20, 10, 0, [switch_utility] cmd=VLAN_PortMemberAdd 2 6 0 [switch_utility] switch_utility, VLAN_PortMemberAdd, 2, 6, 0, [switch_utility] cmd=VLAN_PortMemberAdd 20 6 0 [switch_utility] switch_utility, VLAN_PortMemberAdd, 20, 6, 0, [switch_utility] cmd=VLAN_PortMemberAdd 50 11 0 [switch_utility] switch_utility, VLAN_PortMemberAdd, 50, 11, 0, [switch_utility] cmd=VLAN_PortMemberAdd 50 10 0 [switch_utility] switch_utility, VLAN_PortMemberAdd, 50, 10, 0, [switch_utility] cmd=MAC_TableEntryAdd 2 6 0 1 00:00:00:00:00:00 [switch_utility] switch_utility, MAC_TableEntryAdd, 2, 6, 0, 1, 00:00:00:00:00:00, Interface 3 ip = 0.0.0.0 gConfig.Interface[4].IP_Addr = 0.0.0.0 gConfig.Interface[4].Subnet_Mask = 0.0.0.0 gConfig.Interface[4].Description = ATM2 gConfig.Interface[4].Framing = AAL5 gConfig.Interface[4].VLAN_Idx = 1 ifp->ipaddr = C0A80201 ifp->netmask = FFFFFF00 gConfig.Vlan_Ports[gConfig.Interface[4].VLAN_Idx].VNet = 0 gConfig.Vlan_Ports[gConfig.Interface[4].VLAN_Idx].IGMP_Querier_Enable = 0 [IfInit] ifno=4, gConfig.Interface[4].vlan_tagged=0, line 693 [sar_0_init] ifno=4, T_WAN_INT=3, sar_init=1, g_atm_priv_data.max_connections=15 ATM_VBR_NRT [ppe_open] g_atm_priv_data.connection_table=1 [ppe_open] (8.38): conn = 1, f_enable_irq=0 [sar_0_init] index=1, ifno=4, f_llc=1 [mpoa_setup] mpoa_type=0, f_llc=1 [sar_0_init] Init SAR ifno:4, vlan_tagged=0, g_atm_vcc[1] CONN:1 VPI/VCI:8/38 PORT:0 [sar_0_init] sar ifno: 4, flag: 0x00000220, up, sar_init=1 MAC Address: 4c:09:d4:a2:48:e6 [sar_0_ioctl] ifno 4 up/down 0 ->br_MacAddress=4C-09-D4-A2-48-E6 Interface 4 ip = 192.168.2.1 [sar_0_ioctl] ifno 4 up/down 0 ->gConfig.Interface[27].IP_Addr = 0.0.0.0 gConfig.Interface[27].Subnet_Mask = 0.0.0.0 gConfig.Interface[27].Description = COM1 gConfig.Interface[27].Framing = pppInit> set (PPPShutdownRequest[ifno] = 0) >>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>> if_umts_init 27 <<<<<<<<< if_umts_init() WAN interface 27, UMTS-COM1: baudrate=115200 if_umts_init() MAC:4C:09:D4:A2:48:E6 RUNTASK id=2 sc0.umtsEventHandleTsk() priority:120, infoIdx:0 ... RUNTASK id=3 sc0.umtsEventExeHandleTsk() priority:120, infoIdx:1 ... umtsReceQueueInit() Host controller disable, bypass queue init... RUNTASK id=4 27.umtsReceQueueTsk() priority:120, infoIdx:2 ... RUNTASK id=5 27.umtsReceTsk() priority:119, infoIdx:3 ... umtsWritQueueInit() Host controller disable, bypass queue init... RUNTASK id=6 27.umtsWritTsk() priority:119, infoIdx:4 ... RUNTASK id=7 27.umtsDataIntrTsk() priority:119, infoIdx:5 ... Interface 27 ip = 0.0.0.0 ruleCheck()> Group: 0, Error: Useless rule index will be truncated, from idx:2 ruleCheck()> Group: 1, Error: Useless rule index will be truncated, from idx:22 ruleCheck()> Group: 2, Error: Useless rule index will be truncated, from idx:0 CBAC rule format check succeed !! reqCBACBuf()> init match pool, Have: 1000 Memory Address: 0xffffffff86128ff4 ~ 0xffffffff8612fd70 reqCBACBuf()> init timeGap pool, Have: 10000 Memory Address: 0xffffffff8612fd70 ~ 0xffffffff86160ac4 reqCBACBuf()> init sameHost pool, Have: 2000 Memory Address: 0xffffffff86160ac4 ~ 0xffffffff861704e4 CBAC rule pool initialized !! [init_if] local_if_mask=0x7f80007 [init_if] local_wiredif_mask=0x780002 [init_if] local_wirelessif_mask=0x7800004 [init_if] localorVPN_if_mask=0x7f80007 Init NAT data structure RUNTASK id=8 if_task if0... RUNTASK id=9 if_task if1... RUNTASK id=10 if_task if2... RUNTASK id=11 if_task if3... RUNTASK id=12 if_task if4... RUNTASK id=13 if_task if27... RUNTASK id=14 timer_task... RUNTASK id=15 conn_mgr... RUNTASK id=16 main_8021x... Build Day = Mar 25 2015 RUNTASK id=17 saveRandomSeedTask... [VFS_init] Start... [VFS_init] vfsState:1 vfs_codepage_init() TimeZone:25, vfs_cp_idx:25, vfs_cp_ID:1 fat_codePageInit() TimeZone:25, codePage:Unknown, cPID:1, cpSize:256, toUpSize:0 ntfs_codepage timezone:25, lan= 0 ntfs_codePageInit() TimeZone:25, codePage:1 ==[vfs_register_filesystem]============================ list size:1, Method:0x80ab0d8c 1) Type:0xfc, Name:BRN-VFS ================================================================= [VFS_init] VFS ROOT FS init OK ==[vfs_register_filesystem]============================ list size:7, Method:0x80ab0f8c 1) Type:0x01, Name:FAT12 2) Type:0x04, Name:FAT16 3) Type:0x06, Name:FAT16 4) Type:0x0b, Name:FAT32 5) Type:0x0c, Name:FAT32 6) Type:0x0e, Name:FAT16 7) Type:0x81, Name:Minix ================================================================= [VFS_init] FAT init OK ==[vfs_register_filesystem]============================ list size:1, Method:0x80ab1b94 1) Type:0x07, Name:NTFS/HPFS ================================================================= [VFS_init] NTFS init OK [VFS_init]-[vfs_mount_root] Start... [VFS_init]-[vfs_mount_root] Init <root> OK... [VFS_init]-[vfs_mount_root] Init <dev> OK... [VFS_init]-[vfs_mount_root] Init <mnt> OK... [0-START]========================================= Node 000-[\], DIR, MountFlag:0x00 [0-END]=========================================== [1-START]========================================= Node 001-[dev], DIR, MountFlag:0x00 [1-END]=========================================== [1-START]========================================= Node 002-[mnt], DIR, MountFlag:0x00 [1-END]=========================================== dump_inode() freeCnt:77, usedCnt:3 RUNTASK id=18 fileChange_eventTsk()... [USB-INIT] main() ====== call UsbSysInit() ... [USB] UsbSPoolArray: 85E6B090H ~ 85F6BE8F, UsbSPool:85E6B0A0 [USB] UsbMPoolArray: 85C5388CH ~ 85E6AB0B, UsbMPool:85C538A0 [USB] UsbLPoolArray: 85F73E9CH ~ 85FE26BB, UsbLPool:85F73EA0 [USB] Small Un-Cached Memory(5977): 85E6B0A0 ~ 85F6BDCF [USB] Medium Un-Cached Memory(530): 85C538A0 ~ 85E69ADF [USB] Large Un-Cached Memory(25): 85F73EA0 ~ 85FDE29F setUsbPciInfo() cpu_to_usb_addr_shift[5]:0x00000000, usb_to_cpu_addr_shift[5]:0x00000000 usb_pci_probe() Found Synopsis OTG-1, baseAddr:0xbe101000, IRQ:54 usb_hcd_init() probe PCI function:1 !! otg_host_power_set() USB Host0 Power ON usb_host_power_set() isOn:1 usb_host_power_set() Previous power off:0, current time:0 usb_host_power_set(1) min time delay:6000, current delay:0 usb_host_power_set() Need delay:6500 **********0 usb_host_power_set(2) min time delay:6000, current delay:0 dwc_otg_vbus_on(NULL) Enable USB power!! usb_hcd_init() func(0):0 usb_hcd_init() func(1):0 usb_hcd_init() func(2):0 usb_hcd_init() func(3):0 usb_hcd_init() func(4):0 usb_hcd_init() func(5):1 localhc_init() install otg driver(host_drv = 0x80C243A0, otg_driver=0x80C243A0). usb_hcd_init() func(6):0 usb_hcd_init(): succ. RUNTASK id=19 UsbSysInitTask() priority:120, infoIdx:0 ... [USB-INIT] main() ====== after call UsbSysInit() InitCommSys: RESOURCE_BASE = 173, NUMRES = 640 InitCommSys: EVENT_BASE = 365, NUMEVT = 818 InitCommSys: MAILBOX_BASE = 6, NUMMBX = 64 RUNTASK id=20 period_task... [Dhcpd_Start] RUNTASK id=21 dhcp_daemon... RUNTASK id=22 dhcp_clt... on interface 3 main()> usb:1, ftp:0 Primary image: 0, flash area 1 found signature: 78h 56h 34h 12h ulImgLens=2881196, LENGTH[1]-12=10485748, type:0 length checking OK [0]2 find End at 0xFFFFFFFF84F0E0DC len=2881196, type=0 found signature: 78h 56h 34h 12h ulImgLens=1380382, LENGTH[1]-12=10485748, type:10 length checking OK [1]2 find End at 0xFFFFFFFF8505F4DC len=1380382, type=10 found signature: 78h 56h 34h 12h ulImgLens=411468, LENGTH[1]-12=10485748, type:11 length checking OK [2]2 find End at 0xFFFFFFFF850C3CDC len=411468, type=11 found signature: 78h 56h 34h 12h ulImgLens=405996, LENGTH[1]-12=10485748, type:12 length checking OK [3]2 find End at 0xFFFFFFFF851270DC len=405996, type=12 ---[ LZMA head start in 0xFFFFFFFF851274DC ]--- found signature: 78h 56h 34h 12h ulImgLens=416225, LENGTH[1]-12=10485748, type:50 length checking OK [4]2 find End at 0xFFFFFFFF8518CCDC len=416225, type=50 ---[ LZMA head start in 0xFFFFFFFF8518D0DC ]--- found signature: 78h 56h 34h 12h ulImgLens=363500, LENGTH[1]-12=10485748, type:90 length checking OK [5]2 find End at 0xFFFFFFFF851E5CDC len=363500, type=90 Image[1] at 0x84C4ECDC, len=2881196, type=0 Image[2] at 0x84F0E4DC, len=1380382, type=10 Image[3] at 0x8505F8DC, len=411468, type=11 Image[4] at 0x850C40DC, len=405996, type=12 Image[5] at 0x851274DC, len=416225, type=50 Image[6] at 0x8518D0DC, len=363500, type=90 [get_web_address] Web-0: addr:0x84f0e4dc, len:1380382, type:10 [get_web_address] Web-1: addr:0x8505f8dc, len:411468, type:11 [get_web_address] Web-2: addr:0x850c40dc, len:405996, type:12 getUnZipFileLength: [ZIP 3] getUnZipFileLength: [ZIP 1] Unzipping from 84F0E4DC to 87C76800 ... unzip_address sig 4051120 pre, zipfile=0x84f0e4dc, unzipfile=0x87c76800 unzip_address sig 20110504 end [ZIP 3] unzip_address sig 5d000080 pre, zipfile=0x84f0e4e0, unzipfile=0x87c76800 unzip_address sig 8000005d end [ZIP 1] done Uncompressed size = 2659426 MAX_LANG_SUPPORT=3, COMMON_UI_IMAGES_NUM=1 getUnZipFileLength: [ZIP 3] getUnZipFileLength: [ZIP 1] [absread] flash_init: pfs image found at ffffffff8505f8dc, size is 1640588 bytes Unzipping from 8505F8DC to 87AE5C00 ... unzip_address sig 4051120 pre, zipfile=0x8505f8dc, unzipfile=0x87ae5c00 unzip_address sig 20110504 end [ZIP 3] unzip_address sig 5d000080 pre, zipfile=0x8505f8e0, unzipfile=0x87ae5c00 unzip_address sig 8000005d end [ZIP 1] done Uncompressed size = 1640588 unzip from ffffffff8505f8dc to ffffffff87ae5c00 getUnZipFileLength: [ZIP 3] getUnZipFileLength: [ZIP 1] [absread] flash_init: pfs image found at ffffffff850c40dc, size is 1646147 bytes Unzipping from 850C40DC to 87953A00 ... unzip_address sig 4051120 pre, zipfile=0x850c40dc, unzipfile=0x87953a00 unzip_address sig 20110504 end [ZIP 3] unzip_address sig 5d000080 pre, zipfile=0x850c40e0, unzipfile=0x87953a00 unzip_address sig 8000005d end [ZIP 1] done Uncompressed size = 1646147 unzip from ffffffff850c40dc to ffffffff87953a00 No more PFS image [absread] flash_init: MULTI_LANG_IN_RAM mode, extract 3 aux images RUNTASK httpd... RUNTASK id=27 SSLClient ... g_Client_Cert_Array=0x833b4724 RUNTASK id=28 dnsproxy... startNBIOSTask()... RUNTASK id=29 nbios_main... RUNTASK id=30 padmin_task_entry... RUNTASK id=31 dhcpd_mgmt_task... runDDNS() ddns_enable:0, DDNSTaskRun:0, needReRunDDNS:1 UPnP task run-up... upnpFunc:1 UPNP Device initialize success! slot=32 TR64 is enabled TR64 Device initialize success! slot=33 update_device_OUI: OUI_str=4C09D4 [0] Allocate mailbox 6 [0] Allocate mailbox 7 Begin search NamePath = InternetGatewayDevice.DeviceInfo.FirstUseDateBegin search NamePath = InternetGatewayDevice.DeviceInfo.FirstUseDateFirstUseDate:2015-05-20T23:33:16 RUNTASK id=36 wscinit... RUNTASK id=37 WscSendEapPacket... RUNTASK id=38 wsc_Send_UPNP_packet... UART RX Input Starting Multitask... rzMemory start: 0x83254F14, end 0x833B4714, size 1439744RUNTASK id=39 xdsl_mgmt_task... [0] Allocate resource 173, FreeResource = 1 ifx_pmu_set: PMU_PWDCR0 = 0x8611909f module 8 regid 0 regbit 8 ifx_pmu_set: Actual enabling.......... 1 ifx_pmu_set: Module SPI has been activated 1 times before [KERN_INFO]IFX SSC driver, version 2.1.3, (c)2009 Infineon Technologies AG call ifx_ssc_init() = 0 ifx_pmu_set: PMU_PWDCR0 = 0x8611809f module 12 regid 0 regbit 12 ifx_pmu_set: Actual enabling.......... 1 ifx_pmu_set: Module GPTC has been activated 1 times before [KERN_INFO]gptu: totally 6 16-bit timers/counters IrqConnect : IRQ = 118, Handler = 0x805191C4 [KERN_INFO]gptu: succeeded to request irq 118 IrqConnect : IRQ = 119, Handler = 0x805191C4 [KERN_INFO]gptu: succeeded to request irq 119 IrqConnect : IRQ = 120, Handler = 0x805191C4 [KERN_INFO]gptu: succeeded to request irq 120 IrqConnect : IRQ = 121, Handler = 0x805191C4 [KERN_INFO]gptu: succeeded to request irq 121 IrqConnect : IRQ = 122, Handler = 0x805191C4 [KERN_INFO]gptu: succeeded to request irq 122 IrqConnect : IRQ = 123, Handler = 0x805191C4 [KERN_INFO]gptu: succeeded to request irq 123 do_div error ??? [KERN_INFO]ifx_gptu_timer_set(4, 10000), divider = 25000000 request_timer(4, 0x0000010D, 25000000) [KERN_INFO]request_timer(4, 0x0000010D, 25000000)...ifx_pmu_set: PMU_PWDCR0 = 0x8611809f module 12 regid 0 regbit 12 ifx_pmu_set: Module GPTC has been activated 2 times before successful! Init timer (4) - OK do_div error ??? [KERN_INFO]ifx_gptu_timer_set(6, 100000), divider = 2500000 request_timer(6, 0x0000010D, 2500000) [KERN_INFO]request_timer(6, 0x0000010D, 2500000)...successful! Init timer (6) - OK RUNTASK id=41 apAppInit... RUNTASK id=44 vinax_task... start http redir. RUNTASK id=45 hr_daemon... RUNTASK id=46 hr_misc_daemon... run_project_task:2190 autoWanDetectTask port_mask 0f enable 1 <6>ADM5120 Board Driver, Version 0.0.4.1 <6>(c) Copyright 2003, Infineon Technologies AG Board_InitIrq! Board_InitIrq! --> drv_danube_rb_init() finished ... MEI CPE Driver, Version 1.4.1 (c) Copyright 2012, Lantiq Deutschland GmbH ### MEI CPE - MEI CPE - MEI CPE - MEI CPE ### Using major number 4 ifx_pmu_set: PMU_PWDCR0 = 0x8611809f module 9 regid 0 regbit 9 ifx_pmu_set: Module DSL-DFE has been activated 2 times before --> drv_vinax_init() finished ... get_sleep_evt = 139 --> DSL_ModuleInit() finished ... MEI_OpenOS() line:0 begin ... -->VINAX control device open finished ... T >> init dev: base address = 0xBE116000 T >> parse: opt value = 99 T >> open device: /dev/mei_cpe/0. MEI_drv_test(): fd = 0 T >> ioct(FIO_MEI_DEV_INIT): baseaddr = 0xBE116000, IRQ = 99 pInitDev->meiBaseAddr=0xbe116000 MEI_DRV[00]: INIT DEVICE - NO INTERUPTS --> ACTIVE POLL MODE MEI_DRV[00]: Start Driver Control Thread ##### [IFXOS_ThreadInit] name <VrxCtrl>, tid 50, nStackSize=10000 T >> Line = 00 Return = 0 --> drv_vinax_cfg() finished ... [DSL_CPE_ArgParse] fw1 name= Image[1] at 0x84C4ECDC, len=2881196, type=0 Image[2] at 0x84F0E4DC, len=1380382, type=10 Image[3] at 0x8505F8DC, len=411468, type=11 Image[4] at 0x850C40DC, len=405996, type=12 Image[5] at 0x851274DC, len=416225, type=50 Image[6] DSL[00]: Autoboot State : LinkActivateWait GenaInit : event_hook is NULL!! >> Parse Service 'urn:schemas-microsoft-com:service:OSInfo:1' : TRUE >> Parse Service 'urn:schemas-upnp-org:service:Layer3Forwarding:1' : TRUE >> Parse Service 'urn:schemas-upnp-org:service:WANCommonInterfaceConfig:1' : TRUE >> Parse Service 'urn:schemas-upnp-org:service:WANEthernetLinkConfig:1' : TRUE >> Parse Service 'urn:schemas-upnp-org:service:WANPPPConnection:1' : TRUE >> Parse Service 'urn:schemas-upnp-org:service:WANIPConnection:1' : TRUE >> Parse Device 'urn:schemas-upnp-org:device:WANConnectionDevice:1' : TRUE >> Parse Device 'urn:schemas-upnp-org:device:WANDevice:1' : TRUE >> Parse Device 'urn:schemas-upnp-org:device:InternetGatewayDevice:1' : TRUE ********** upnp_main1() Record pDevRoot[1]:831dfab0 >>>>>>>>>>FRegisterDevice pDev->rootDevHeadType = [0] >>>>>>>>>>FRegisterDevice pDev->rootDevHeadType = [0] >>>>>>>>>>FRegisterDevice pDev->rootDevHeadType = [0] >>>> UPNP init IGD device successfully ... upnp_main(2-0) Run-up UPnP device TR64... readXML: fname=/tr64_igd.xml upnp_Init(0) upnpGlobalInit[2]:0 >> Parse Service 'urn:dslforum-org:service:DeviceInfo:1' : TRUE >> Parse Service 'urn:dslforum-org:service:DeviceConfig:1' : TRUE >> Parse Service 'urn:dslforum-org:service:LANEthernetInterfaceConfig:1' : TRUE >> Parse Service 'urn:dslforum-org:service:WLANConfiguration:1' : TRUE >> Parse Device 'urn:dslforum-org:device:LANDevice:1' : TRUE >> Parse Service 'urn:dslforum-org:service:WANDSLInterfaceConfig:1' : TRUE >> Parse Service 'urn:dslforum-org:service:WANPPPConnection:1' : TRUE >> Parse Device 'urn:dslforum-org:device:WANConnectionDevice:1' : TRUE >> Parse Device 'urn:dslforum-org:device:WANDevice:1' : TRUE >> Parse Device 'urn:dslforum-org:device:InternetGatewayDevice:1' : TRUE ********** upnp_main1() Record pDevRoot[2]:831b31f4 TR64DBUG::TR64_UPnPInit> Start: >>>>>>>>>>FRegisterDevice pDev->rootDevHeadType = [1] >>>>>>>>>>FRegisterDevice pDev->rootDevHeadType = [0] >>>>>>>>>>FRegisterDevice pDev->rootDevHeadType = [0] >>>>>>>>>>FRegisterDevice pDev->rootDevHeadType = [0] >>>> UPNP init TR64 device successfully ... upnp_main(3-0) Run-up UPnP device WPS-WCN... readXML: fname=/wcn.xml upnp_Init(0) upnpGlobalInit[3]:0 >> Parse Service 'urn:schemas-wifialliance-org:service:WFAWLANConfig:1' : TRUE >> Parse Device 'urn:schemas-wifialliance-org:device:WFADevice:1' : TRUE ********** upnp_main1() Record pDevRoot[3]:8319d8a0 >>>>>>>>>>FRegisterDevice pDev->rootDevHeadType = [0] -------UPnP_WSC_Init------ >>>> UPNP init WPS-WCN device successfully ... upnp_main(4-0) Run-up UPnP device AV Media Server... readXML: fname=/avServer.xml upnp_Init(0) upnpGlobalInit[4]:0 >> Parse Service 'urn:schemas-upnp-org:service:ConnectionManager:1' : TRUE >> Parse Service 'urn:schemas-upnp-org:service:ContentDirectory:1' : TRUE >> Parse Service 'urn:microsoft.com:service:X_MS_MediaReceiverRegistrar:1' : TRUE >> Parse Device 'urn:schemas-upnp-org:device:MediaServer:1' : TRUE ********** upnp_main1() Record pDevRoot[4]:831922cc >>>>>>>>>>FRegisterDevice pDev->rootDevHeadType = [0] QueryCurrentConnectionIDs.... >>>> UPNP init AV Media Server device successfully ... ********** upnp_main() Unsupportted UPnP root device[5]: AV Media Renderer ********** upnp_main() Unsupportted UPnP root device[6]: Printer DSL[00]: modem state = 0x00000100, 3327 ----------set nmode=1--- [Set1Xconfig] wpa2flag=0x2 [Set1Xconfig] cypher_suite=0x33 Setting Wireless Country Code : 0x2d4 Setting DTIMPeriod : 3 Setting BeaconPeriod : 100 Setting gfragThreshold:2346 Setting grtsThreshold:2346 Setting PreambleType:1 Setting TxBurst:1 Setting TxAntenna:3 wme_ac ap be ecwmax 6 ecwmin 4 txop 0 aifsn 3 acm 0wme_ac ap bk ecwmax 10 ecwmin 4 txop 0 aifsn 7 acm 0 wme_ac ap vi ecwmax 4 ecwmin 3 txop 94 aifsn 1 acm 0wme_ac ap vo ecwmax 3 ecwmin 2 txop 47 aifsn 1 acm 0wme_ac sta be ecwmax 10 ecwmin 4 txop 0 aifsn 3 acm 0wme_ac sta bk ecwmax 10 ecwmin 4 txop 0 aifsn 7 acm 0wme_ac sta vi ecwmax 4 ecwmin 3 txop 94 aifsn 2 acm 0wme_acSetting APSDCapable:1 Setting GF_Mode:0 Setting ShortGI 20MHz:1 40MHz:1 Setting Mpdudensity:6 Setting AMSDU enable:0 wl0: wl_up DSL[00]: Autoboot State : Train DSL[00]: modem state = 0x00000200, 4349 IFXOS_EventWait: -20 ifx_mps_get_fw_version: ifx_mps_mbx_write_message... ifx_mps_get_fw_version: Before sleep ifx_mps_get_fw_version: After sleep! ifx_mps_get_fw_version: ifx_mps_mbx_read_message retval 0 bytes_read 8 ok! Version 2.1.1.7.0 up and running... VMMC_TAPI_LL_FW_Start: ifx_mps_ioctl ret 0 IFX_TAPI_Phone_Init: TAPI FW_Start 0 [42] Allocate resource 187, FreeResource = 15 [42] Allocate resource 188, FreeResource = 16 [42] Allocate resource 189, FreeResource = 17 [42] Allocate resource 190, FreeResource = 18 [42] Allocate resource 191, FreeResource = 19 [42] Allocate resource 192, FreeResource = 20 [42] Allocate resource 193, FreeResource = 21 [42] Allocate resource 194, FreeResource = 22 [42] Allocate resource 195, FreeResource = 23 [42] Allocate resource 196, FreeResource = 24 [42] Allocate resource 197, FreeResource = 25 [42] Allocate resource 198, FreeResource = 26 [42] Allocate resource 199, FreeResource = 27 [42] Allocate resource 200, FreeResource = 28 [42] Allocate resource 201, FreeResource = 29 [42] Allocate resource 202, FreeResource = 30 [42] Allocate resource 203, FreeResource = 31 [42] Allocate resource 204, FreeResource = 32 [42] Allocate resource 205, FreeResource = 33 [42] Allocate resource 206, FreeResource = 34 [42] Allocate resource 207, FreeResource = 35 [42] Allocate resource 208, FreeResource = 36 [42] Allocate resource 209, FreeResource = 37 [42] Allocate resource 210, FreeResource = 38 [42] Allocate resource 211, FreeResource = 39 [42] Allocate resource 212, FreeResource = 40 [42] Allocate resource 213, FreeResource = 41 [42] Allocate resource 214, FreeResource = 42 [42] Allocate resource 215, FreeResource = 43 [42] Allocate resource 216, FreeResource = 44 [42] Allocate resource 217, FreeResource = 45 [42] Allocate resource 218, FreeResource = 46 [42] Allocate resource 219, FreeResource = 47 IFXOS_EventWait: -20 IFXOS_EventWait: -20 IFXOS_EventWait: -20 IFXOS_EventWait: -20 IFXOS_EventWait: -20 VMMC_TAPI_LL_FW_Init: VMMC_ALM_SmartSLIC_ChGet 2 FXO 0 2 FWCAP: nPCM: 8 nALM: 2 nSIG: 5 nCOD: 5 nDECT: 6 FWCAP: nNLEC: 4 nWLEC: 4 nES: 4 nAGC: 5 nFAX: 5 FWCAP: nUTG:16 UTG/CH: 2 nMFTD: 5 nLIN: 2 FWCAP: nDTMFR: 5 nDTMFG: 5 nCIDS: 5 nCIDR: 5 VMMC_AddCaps: CODECS = 4cf IFXOS_EventWait: -20 IFXOS_EventWait: -20 IFXOS_EventWait: -20 IFXOS_EventWait: -20 IFXOS_EventWait: -20 >>>>>>>>>>>>>>>>>>>>>>>>> IFXOS_EventInit event number 11 [42] Allocate resource 220, FreeResource = 48 >>>>>>>>>>>>>>>>>>>>>>>>> IFXOS_EventInit event number 12 [42] Allocate resource 221, FreeResource = 49 IFXOS_EventWait: -20 IFXOS_EventWait: -20 [reset_802dot1x] wireless module ready [init_wpa] dot1x_ready[0]=3 IFXOS_EventWait: -20 [init_wpa] dot1x_ready[1]=1 [init_wpa] dot1x_ready[2]=1 [init_wpa] dot1x_ready[3]=1 [init_wpa] dot1x_ready[4]=1 [reset_802dot1x] 802.1Xv2 ready wsc_initialized:2 IFXOS_EventWait: -20 IFX_TAPI_Phone_Init: TAPI BBD_Dnld 0 ===> Set PCM I/F 0 VMMC_handle:83234bf4 IFX_TAPI_Phone_Init: TAPI FW_Start 0 ===> VMMC_Ioctl: Phone 1 IFX_TAPI_LINE_TYPE ok! VMMC_Ioctl: Phone 1 IFXPHONE_SET_LINEFEED ok! VMMC_Ioctl: Phone 1 IFX_TAPI_MAP_DATA_ADD ok! Set PCM I/F 1 VMMC_handle:83234bd8 IFX_TAPI_Phone_Init: TAPI FW_Start 0 ===> VMMC_Ioctl: Phone 2 IFX_TAPI_LINE_TYPE ok! VMMC_Ioctl: Phone 2 IFXPHONE_SET_LINEFEED ok! VMMC_Ioctl: Phone 2 IFX_TAPI_MAP_DATA_ADD ok! Set PCM I/F 2 VMMC_handle:83234bbc IFX_TAPI_Phone_Init: TAPI FW_Start 0 ===> Set PCM I/F 3 VMMC_handle:83234ba0 IFX_TAPI_Phone_Init: TAPI FW_Start 0 ===> Set PCM I/F 4 VMMC_handle:83234b84 IFX_TAPI_Phone_Init: TAPI FW_Start 0 ===> Set PCM I/F 5 VMMC_handle:83234b68 IFX_TAPI_Phone_Init: TAPI FW_Start 0 ===> Set PCM I/F 6 VMMC_handle:83234b4c IFX_TAPI_Phone_Init: TAPI FW_Start 0 ===> Set PCM I/F 7 VMMC_handle:83234b30 IFX_TAPI_Phone_Init: TAPI FW_Start 0 ===> Set PCM I/F 8 VMMC_handle:83234b14 Setting HOOK Related Parameters 0 Setting HOOKFLASH_TIME min 50 ms max 350 ms Setting HOOKON_TIME min 320 max 320 Setting HOOK Related Parameters 1 Setting HOOKFLASH_TIME min 50 ms max 350 ms Setting HOOKON_TIME min 320 max 320 Setting HOOK Related Parameters 2 Setting HOOK Related Parameters 3 RUNTASK id=30 VINETIC_DRV_Task... [41] Allocate mailbox 25 RUNTASK id=41 VINETIC_T38_Task... RUNTASK id=32 VOICE_API_task... ************** Enable ProDaaCheckInterrupt() detect 8009 Reset Duslic High begin Reset Duslic end ProDAAInitialize: begin now ProDAAInitialize: Line-Side Device Status 0 Port 2 sytem-side revision 0, line-side revision 0 init_DTMF_data: time 8743 force_daa_offhook ch 2 onoff 1 time 8743 ProDaaOffhook 0 2 onoff 1 CID_Detect CH 2 onoff 0 FXO_PolState_DTMFCID --> Disable DTMF CID force_daa_offhook ch 2 onoff 0 time 8802 ProDaaOffhook 0 2 onoff 0 CID_Detect CH 2 onoff 1 failed FXO_PolState_DTMFCID --> Detect Polarity Changed Enable DTMF CID Relay Off now ch:0 When * the value is 60000 When * the value is 60000 When * the value is 60000 sys_voip_cfg->cpt.reorder = 425@-230;20(0.24/0.24/1) TEL_DRV_TONE_REORDER duration = 480 [42] Allocate resource 222, FreeResource = 50 [42] Allocate mailbox 26 TEL_MGR_Init [42] Allocate resource 223, FreeResource = 51 tel_mgr_mutex=223 [42] Allocate mailbox 27 TEL_DM_Init [42] Allocate resource 224, FreeResource = 52 [42] Allocate resource 225, FreeResource = 53 TEL_MGR_VoiceChannelInit TEL_MGR_SetVoiceChannel 1 TEL_MGR_SetPhoneEC TEL_MGR_SetPhoneVAD TEL_MGR_SetPhoneGain TEL_MGR_SetPhoneJitter TEL_MGR_SetVoiceChannel 2 TEL_MGR_SetPhoneEC TEL_MGR_SetPhoneVAD TEL_MGR_SetPhoneGain TEL_MGR_SetPhoneJitter TEL_MGR_SetVoiceChannel 5 TEL_MGR_SetPhoneEC ##@@!! TEL_MGR_SetPhoneEC: USB_DECT_Phone need to change here TEL_MGR_SetPhoneVAD ##@@!! VOICE_DRV_SetVAD: channelId 6 >= USB_DECT_CHANNEL_START 5 TEL_MGR_SetPhoneGain ##@@!! TEL_MGR_SetPhoneGain: USB_DECT_Phone need to change here TEL_MGR_SetPhoneJitter ##@@!! TEL_MGR_SetPhoneJitter: USB_DECT_Phone need to change here TEL_MGR_SetVoiceChannel 6 TEL_MGR_SetPhoneEC ##@@!! TEL_MGR_SetPhoneEC: USB_DECT_Phone need to change here TEL_MGR_SetPhoneVAD ##@@!! VOICE_DRV_SetVAD: channelId 7 >= USB_DECT_CHANNEL_START 5 TEL_MGR_SetPhoneGain ##@@!! TEL_MGR_SetPhoneGain: USB_DECT_Phone need to change here TEL_MGR_SetPhoneJitter ##@@!! TEL_MGR_SetPhoneJitter: USB_DECT_Phone need to change here TEL_MGR_SetVoiceChannel 7 TEL_MGR_SetPhoneEC ##@@!! TEL_MGR_SetPhoneEC: USB_DECT_Phone need to change here TEL_MGR_SetPhoneVAD TEL_MGR_SetPhoneGain ##@@!! TEL_MGR_SetPhoneGain: USB_DECT_Phone need to change here TEL_MGR_SetPhoneJitter ##@@!! TEL_MGR_SetPhoneJitter: USB_DECT_Phone need to change here TEL_MGR_SetVoiceChannel 8 TEL_MGR_SetPhoneEC ##@@!! TEL_MGR_SetPhoneEC: USB_DECT_Phone need to change here TEL_MGR_SetPhoneVAD TEL_MGR_SetPhoneGain ##@@!! TEL_MGR_SetPhoneGain: USB_DECT_Phone need to change here TEL_MGR_SetPhoneJitter ##@@!! TEL_MGR_SetPhoneJitter: USB_DECT_Phone need to change here [42] Allocate resource 226, FreeResource = 54 [42] Allocate mailbox 28 SIP_CORE_Task 1130 ######### ** sip_core_config.laddr = 192.168.1.1 [67] Allocate resource 227, FreeResource = 55 [67] Allocate resource 228, FreeResource = 56 [SIP_CORE_Task] sip_core_ready TEL_MGR_SetVoipPhoneEvtHookFunc TEL_MGR_SetVoipPhoneEvtHookFunc TEL_MGR_SetVoipPhoneEvtHookFunc TEL_MGR_SetVoipPhoneEvtHookFunc TEL_MGR_SetVoipPhoneEvtHookFunc TEL_MGR_SetVoipPhoneEvtHookFunc TEL_MGR_SetVoipPhoneEvtHookFunc TEL_MGR_SetVoipPhoneEvtHookFunc #[SIP_CORE_SetVcIPAddr] 15451, vc: 3, ip:192.168.1.1 [SIP_CORE_SetVcIPAddr] vcIdx=3 ip=192.168.1.1 [SIP_CORE_StopVc] vcIdx=3 [42] Allocate resource 229, FreeResource = 57 [42] Allocate mailbox 29 VOICE_IVR_Init: voice_ivr_channel[0].ivrQueueId = 29 [42] Allocate mailbox 30 VOICE_IVR_Init: voice_ivr_channel[1].ivrQueueId = 30 [42] Allocate mailbox 31 VOICE_IVR_Init: voice_ivr_channel[2].ivrQueueId = 31 [42] Allocate mailbox 32 VOICE_IVR_Init: voice_ivr_channel[3].ivrQueueId = 32 [42] Allocate mailbox 33 VOICE_IVR_Init: voice_ivr_channel[4].ivrQueueId = 33 [42] Allocate mailbox 34 VOICE_IVR_Init: voice_ivr_channel[5].ivrQueueId = 34 [42] Allocate mailbox 35 VOICE_IVR_Init: voice_ivr_channel[6].ivrQueueId = 35 [42] Allocate mailbox 36 VOICE_IVR_Init: voice_ivr_channel[7].ivrQueueId = 36 TEL_MGR_DisableDebug TEL_IVR_CheckMICabort() Start !! [SIP_CORE_StopVc] stop account 1 [SIP_CORE_StopVc] stop account 2 [SIP_CORE_StopVc] stop account 3 SIP_CORE_VcIpAddr[3]= [SIP_CORE_LibInit_By_Account] invoke uaLibInit_VC(,,1) [SIP_CORE_LibInit_By_Account] invoke uaLibInit_VC(,,2) [SIP_CORE_LibInit_By_Account] invoke uaLibInit_VC(,,3) [17] Allocate resource 230, FreeResource = 58 [17] Allocate resource 231, FreeResource = 59 [17] Allocate resource 232, FreeResource = 60 [17] Allocate resource 233, FreeResource = 61 [17] Allocate resource 234, FreeResource = 62 [17] Allocate resource 235, FreeResource = 63 DSL[00]: Reboot on training timeout (60)!!! DSL[00]: Autoboot State : Restart DSL[00]: Autoboot State : ShutDownRequest DSL[00]: Autoboot State : ShutDownWait DSL[00]: modem state = 0x00000860, 65371 DSL[00]: Autoboot State : ShutDownReached DSL[00]: Autoboot State : Restart DSL[00]: Autoboot State : FirmwareRequest DSL[00]: Autoboot State : FirmwareWait DSL[00]: @@@@@@@@@@@@@ DSL_CPE_DownloadFirmware() @@@@@@@@@@@@@ DSL[00]: nFwReqType = 3, Fw name1=NULL, name2=NULL DSL[00]: DSL_FW_REQUEST_ADSL in DSL_DRV_DEV_FwDownload DSL[00]: modem state = 0x000000ff, 66407 DSL[00]: Autoboot State : firmwareReady DSL[00]: Autoboot State : Init DSL[00]: Autoboot State : LinkActivateWait DSL[00]: Autoboot State : Train DSL[00]: modem state = 0x00000200, 68409


This mode can be accessed via soft hack. Check above.

ROM VER: 1.1.4 CFG 06 NAND NAND Read OK DDR PARAM flash addr 1700000 DDR PARAM: 88888888 001a2520 001a2120 00566301 00566501 00000200 DDR autotuning Rev 1.0 DDR check ok... start booting... END TUNE DDR Start booting........... ======================================================================= Wireless ADSL IAD VR9 Loader v2.01.07 build Oct 22 2014 16:13:17 Arcadyan Technology Corporation ======================================================================= Init......read page ECC check ret = -1, addr = 0x01700000 NAND Read Error: addr 0x1700000 read 0x01700000 ERROR: ret = 0 Image Check from FLASH_AREA_IMAGE_1 : Unzipping firmware at 0x80002000 ... with nAREA[2]read page ECC check ret = -1, addr = 0x014FFFF4 NAND Read Error: addr 0x14ffff4 read 0x014FFFF4 ERROR: ret = 0 failed : 4 !! Try unzipping firmware again...read page ECC check ret = -1, addr = 0x00B00800 NAND Read Error: addr 0xb00800 read 0x00B00000 ERROR: ret = 0 failed : 4 !! Unzipping firmware at 0x80002000 ... with nAREA[1] failed : 4 !! Try unzipping firmware again...read page ECC check ret = -1, addr = 0x00107000 NAND Read Error: addr 0x107000 read 0x00100000 ERROR: ret = 0 failed : 4 !! Unzipping Tiny Kernel at 0x80002000 ... read page ECC check ret = -1, addr = 0x00000800 NAND Read Error: addr 0x800 read 0x00000000 ERROR: ret = 0 failed : 4 !! [VR9 Boot]:k Unzipping Tiny Kernel at 0x80002000 ... [ZIP 1] done Tiny ETCPIP running ... Ready to run firmware In c_entry() function ... install_exception Co config = 80048483 sys_irq_init ... Tiny Kernel System startup... CPU Clock 500000000 Hz init_US_counter : time1 = 28 , time2 = 3600067, diff 3600039 US_counter = 112 cnt1 4576977 cnt2 4579557, diff 2580 cnt1 4576977 cnt2 4579557, diff 2580 nand_init... MXIC NAND 128MB 3,3V 8-bit found ----------------------------- NAND page size : 2048 NAND oob size : 64 NAND block size : 131072 NAND page/block : 64 NAND block/chip : 1024 NAND chip size : 0x8000000 NAND page shift : 11 NAND page mask : 0xFFFF NAND block shift : 17 ----------------------------- Scan BAD Block ... 0 Bad Block(s) tcpip_startup... Set flash memory layout to BPARAMS+RECOVER_KERNEL Bootcode version: v2.01.07 Serial number : A000000001 Hardware version: R0A !!No configuration file present!! default route: 0.0.0.0 default route: 0.0.0.0 BufferInit: BUF_HDR_SZ=64 BUF_ALIGN_SZ=28 BUFFER_OFFSET=128 BUF_BUFSZ0=384 BUF_BUFSZ1=1632 NUM_OF_B0=24 NUM_OF_B1=800 BUF_POOL0_SZ=10752 BUF_POOL1_SZ=1356800 Buf0_Block 80305d18 Buf1_Block 801ba8f8 BUF0[0]=0x80305d20 BUF1[0]=0x801ba900 buffer0 pointer init OK! buffer1 pointer init OK! init_if() ; gConfig.Interface[0].Link_Type is [4] Interface 0 ip = 127.0.0.1 init_if() ; gConfig.Interface[1].Link_Type is [1] [KERN_INFO]IFX PMU driver, version 1.0.5, (c)2009 Infineon Technologies AG ifx_dma_init_module : [map_dma_chan 1550]: dma_chan[0] request_irq 64 IrqConnect : IRQ = 64, Handler = 0x80015B68 [map_dma_chan 1550]: dma_chan[1] request_irq 65 IrqConnect : IRQ = 65, Handler = 0x80015B68 [map_dma_chan 1550]: dma_chan[2] request_irq 66 IrqConnect : IRQ = 66, Handler = 0x80015B68 [map_dma_chan 1550]: dma_chan[3] request_irq 67 IrqConnect : IRQ = 67, Handler = 0x80015B68 [map_dma_chan 1550]: dma_chan[4] request_irq 68 IrqConnect : IRQ = 68, Handler = 0x80015B68 [map_dma_chan 1550]: dma_chan[5] request_irq 69 IrqConnect : IRQ = 69, Handler = 0x80015B68 [map_dma_chan 1550]: dma_chan[6] request_irq 70 IrqConnect : IRQ = 70, Handler = 0x80015B68 [map_dma_chan 1550]: dma_chan[7] request_irq 71 IrqConnect : IRQ = 71, Handler = 0x80015B68 [map_dma_chan 1550]: dma_chan[8] request_irq 72 IrqConnect : IRQ = 72, Handler = 0x80015B68 [map_dma_chan 1550]: dma_chan[9] request_irq 73 IrqConnect : IRQ = 73, Handler = 0x80015B68 [map_dma_chan 1550]: dma_chan[10] request_irq 74 IrqConnect : IRQ = 74, Handler = 0x80015B68 [map_dma_chan 1550]: dma_chan[11] request_irq 75 IrqConnect : IRQ = 75, Handler = 0x80015B68 [map_dma_chan 1550]: dma_chan[12] request_irq 89 IrqConnect : IRQ = 89, Handler = 0x80015B68 [map_dma_chan 1550]: dma_chan[13] request_irq 90 IrqConnect : IRQ = 90, Handler = 0x80015B68 [map_dma_chan 1550]: dma_chan[14] request_irq 91 IrqConnect : IRQ = 91, Handler = 0x80015B68 [map_dma_chan 1550]: dma_chan[15] request_irq 92 IrqConnect : IRQ = 92, Handler = 0x80015B68 [map_dma_chan 1550]: dma_chan[16] request_irq 93 IrqConnect : IRQ = 93, Handler = 0x80015B68 [map_dma_chan 1550]: dma_chan[17] request_irq 62 IrqConnect : IRQ = 62, Handler = 0x80015B68 [map_dma_chan 1550]: dma_chan[18] request_irq 80 IrqConnect : IRQ = 80, Handler = 0x80015B68 [map_dma_chan 1550]: dma_chan[19] request_irq 85 IrqConnect : IRQ = 85, Handler = 0x80015B68 [map_dma_chan 1550]: dma_chan[20] request_irq 128 IrqConnect : IRQ = 128, Handler = 0x80015B68 [map_dma_chan 1550]: dma_chan[21] request_irq 129 IrqConnect : IRQ = 129, Handler = 0x80015B68 [map_dma_chan 1550]: dma_chan[22] request_irq 130 IrqConnect : IRQ = 130, Handler = 0x80015B68 [map_dma_chan 1550]: dma_chan[23] request_irq 131 IrqConnect : IRQ = 131, Handler = 0x80015B68 [map_dma_chan 1550]: dma_chan[24] request_irq 132 IrqConnect : IRQ = 132, Handler = 0x80015B68 [map_dma_chan 1550]: dma_chan[25] request_irq 133 IrqConnect : IRQ = 133, Handler = 0x80015B68 [map_dma_chan 1550]: dma_chan[26] request_irq 134 IrqConnect : IRQ = 134, Handler = 0x80015B68 [map_dma_chan 1550]: dma_chan[27] request_irq 135 IrqConnect : IRQ = 135, Handler = 0x80015B68 ifx_dma_init_module : g_desc_list 80070ac0 [KERN_INFO]IFX DMA driver, version ifxmips_dma_core.c:v1.0.4 ,(c)2009 Infineon Technologies AG ifx_gpio_init() !!! ifx_gpio_pre_init() !!! [KERN_INFO]IFX GPIO driver, version 1.2.10, (c)2009 Infineon Technologies AG [KERN_INFO]Infineon Technologies RCU driver version 1.0.6 vr9_config_mdio_gpio !!! [KERN_INFO]IFX 7 Port Eth driver, version ifxmips_7port_eth_sw.c:v1.0.0 ,(c)2009 Infineon Technologies AG g_dma_pmac:1, g_pmac_dma:1, reg:0x0000074c !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! IFX SWITCH API, Version 0.8.6 IFX_ETHSW_Open() !!! [KERN_INFO] SWAPI: Registered character device [switch_api] with major no [81] Switch API: PCE MicroCode loaded !! IFX_ETHSW_IOCTL_WrapperInit() !!! IFX_ETHSW_IOCTL_WrapperDeviceAdd : Device Number = 1 chip_id 2000b713 chip_id b Switch Auto Polling value = 0 [KERN_ERR] GPHY FW load for A2x !! vr9_gphy_gpio_init : Config GPIO3 clock !!! vr9_gphy_reset() !!! GPHY FIRMWARE LOAD SUCCESSFULLY AT ADDR : 80000 vr9_gphy_reset_released() !!! vr9_phy_hw_init : Config port 2, 4 PHY address and auto-polling mode [KERN_INFO] IFX GPHY driver, version ifxmips_vr9_gphy:v0.4.0,(c)2009 Infineon Technologies AG switch_utility, RegisterSet, 0xc4B, 0x3F, ioctl is called DEBUG> Minor number = 0 DEBUG> IFX_ETHSW_LowLevelCommandSearch[89]: IOC_TYPE=e9, IOC_NR=1 pDrv=80092864, pDrv->pLlHandle=8009271C IFX_FLOW_RegisterSet : addr 00000c4b data 0000003f switch_utility, RegisterSet, 0xc4C, 0x8105, ioctl is called DEBUG> Minor number = 0 DEBUG> IFX_ETHSW_LowLevelCommandSearch[89]: IOC_TYPE=e9, IOC_NR=1 pDrv=80092864, pDrv->pLlHandle=8009271C IFX_FLOW_RegisterSet : addr 00000c4c data 00008105 switch_utility, RegisterSet, 0xc53, 0x1811, ioctl is called DEBUG> Minor number = 0 DEBUG> IFX_ETHSW_LowLevelCommandSearch[89]: IOC_TYPE=e9, IOC_NR=1 pDrv=80092864, pDrv->pLlHandle=8009271C IFX_FLOW_RegisterSet : addr 00000c53 data 00001811 switch_utility, RegisterSet, 0xc51, 0x1813, ioctl is called DEBUG> Minor number = 0 DEBUG> IFX_ETHSW_LowLevelCommandSearch[89]: IOC_TYPE=e9, IOC_NR=1 pDrv=80092864, pDrv->pLlHandle=8009271C IFX_FLOW_RegisterSet : addr 00000c51 data 00001813 switch_utility, RegisterSet, 0xC52, 0x1812, ioctl is called DEBUG> Minor number = 0 DEBUG> IFX_ETHSW_LowLevelCommandSearch[89]: IOC_TYPE=e9, IOC_NR=1 pDrv=80092864, pDrv->pLlHandle=8009271C IFX_FLOW_RegisterSet : addr 00000c52 data 00001812 switch_utility, RegisterSet, 0xC50, 0x1814, ioctl is called DEBUG> Minor number = 0 DEBUG> IFX_ETHSW_LowLevelCommandSearch[89]: IOC_TYPE=e9, IOC_NR=1 pDrv=80092864, pDrv->pLlHandle=8009271C IFX_FLOW_RegisterSet : addr 00000c50 data 00001814 switch_utility, RegisterSet, 0x903, 0x180, ioctl is called DEBUG> Minor number = 0 DEBUG> IFX_ETHSW_LowLevelCommandSearch[89]: IOC_TYPE=e9, IOC_NR=1 pDrv=80092864, pDrv->pLlHandle=8009271C IFX_FLOW_RegisterSet : addr 00000903 data 00000180 switch_utility, RegisterSet, 0x90F, 0x180, ioctl is called DEBUG> Minor number = 0 DEBUG> IFX_ETHSW_LowLevelCommandSearch[89]: IOC_TYPE=e9, IOC_NR=1 pDrv=80092864, pDrv->pLlHandle=8009271C IFX_FLOW_RegisterSet : addr 0000090f data 00000180 switch_utility, RegisterSet, 0x93F, 0x180, ioctl is called DEBUG> Minor number = 0 DEBUG> IFX_ETHSW_LowLevelCommandSearch[89]: IOC_TYPE=e9, IOC_NR=1 pDrv=80092864, pDrv->pLlHandle=8009271C IFX_FLOW_RegisterSet : addr 0000093f data 00000180 switch_utility, RegisterSet, 0x91B, 0x180, ioctl is called DEBUG> Minor number = 0 DEBUG> IFX_ETHSW_LowLevelCommandSearch[89]: IOC_TYPE=e9, IOC_NR=1 pDrv=80092864, pDrv->pLlHandle=8009271C IFX_FLOW_RegisterSet : addr 0000091b data 00000180 switch_utility, RegisterSet, 0x933, 0x180, ioctl is called DEBUG> Minor number = 0 DEBUG> IFX_ETHSW_LowLevelCommandSearch[89]: IOC_TYPE=e9, IOC_NR=1 pDrv=80092864, pDrv->pLlHandle=8009271C IFX_FLOW_RegisterSet : addr 00000933 data 00000180 switch_utility, RegisterSet, 0x927, 0x180, ioctl is called DEBUG> Minor number = 0 DEBUG> IFX_ETHSW_LowLevelCommandSearch[89]: IOC_TYPE=e9, IOC_NR=1 pDrv=80092864, pDrv->pLlHandle=8009271C IFX_FLOW_RegisterSet : addr 00000927 data 00000180 switch_utility, RegisterSet, 0x94B, 0x180, ioctl is called DEBUG> Minor number = 0 DEBUG> IFX_ETHSW_LowLevelCommandSearch[89]: IOC_TYPE=e9, IOC_NR=1 pDrv=80092864, pDrv->pLlHandle=8009271C IFX_FLOW_RegisterSet : addr 0000094b data 00000180 switch_utility, PortLinkCfgSet, 0, 0, 0, 0, 4, 0, 0, 4, 0, ioctl is called DEBUG> Minor number = 0 DEBUG> IFX_ETHSW_LowLevelCommandSearch[89]: IOC_TYPE=e1, IOC_NR=3f pDrv=80092864, pDrv->pLlHandle=8009271C IFX_FLOW_PortLinkCfgSet : portIdx 0 IFX_FLOW_PortLinkCfgSet : Duplex value 0 IFX_FLOW_PortLinkCfgSet : Speed value 3 IFX_FLOW_PortLinkCfgSet : Link value 0 IFX_FLOW_PortLinkCfgSet : MII_Mode value 4 switch_utility, PortLinkCfgSet, 1, 0, 0, 0, 4, 0, 0, 4, 0, ioctl is called DEBUG> Minor number = 0 DEBUG> IFX_ETHSW_LowLevelCommandSearch[89]: IOC_TYPE=e1, IOC_NR=3f pDrv=80092864, pDrv->pLlHandle=8009271C IFX_FLOW_PortLinkCfgSet : portIdx 1 IFX_FLOW_PortLinkCfgSet : Duplex value 0 IFX_FLOW_PortLinkCfgSet : Speed value 3 IFX_FLOW_PortLinkCfgSet : Link value 0 IFX_FLOW_PortLinkCfgSet : MII_Mode value 4 switch_utility, PortLinkCfgSet, 5, 0, 0, 0, 4, 0, 0, 1, 0, ioctl is called DEBUG> Minor number = 0 DEBUG> IFX_ETHSW_LowLevelCommandSearch[89]: IOC_TYPE=e1, IOC_NR=3f pDrv=80092864, pDrv->pLlHandle=8009271C IFX_FLOW_PortLinkCfgSet : portIdx 5 IFX_FLOW_PortLinkCfgSet : Duplex value 0 IFX_FLOW_PortLinkCfgSet : Speed value 3 IFX_FLOW_PortLinkCfgSet : Link value 0 IFX_FLOW_PortLinkCfgSet : MII_Mode value 1 switch_utility, PortLinkCfgSet, 2, 0, 0, 0, 4, 0, 0, 1, 0, ioctl is called DEBUG> Minor number = 0 DEBUG> IFX_ETHSW_LowLevelCommandSearch[89]: IOC_TYPE=e1, IOC_NR=3f pDrv=80092864, pDrv->pLlHandle=8009271C IFX_FLOW_PortLinkCfgSet : portIdx 2 IFX_FLOW_PortLinkCfgSet : Duplex value 0 IFX_FLOW_PortLinkCfgSet : Speed value 3 IFX_FLOW_PortLinkCfgSet : Link value 0 IFX_FLOW_PortLinkCfgSet : MII_Mode value 1 switch_utility, PortLinkCfgSet, 3, 0, 0, 0, 4, 0, 0, 1, 0, ioctl is called DEBUG> Minor number = 0 DEBUG> IFX_ETHSW_LowLevelCommandSearch[89]: IOC_TYPE=e1, IOC_NR=3f pDrv=80092864, pDrv->pLlHandle=8009271C IFX_FLOW_PortLinkCfgSet : portIdx 3 IFX_FLOW_PortLinkCfgSet : Duplex value 0 IFX_FLOW_PortLinkCfgSet : Speed value 3 IFX_FLOW_PortLinkCfgSet : Link value 0 IFX_FLOW_PortLinkCfgSet : MII_Mode value 1 switch_utility, PortLinkCfgSet, 4, 0, 0, 0, 4, 0, 0, 1, 0, ioctl is called DEBUG> Minor number = 0 DEBUG> IFX_ETHSW_LowLevelCommandSearch[89]: IOC_TYPE=e1, IOC_NR=3f pDrv=80092864, pDrv->pLlHandle=8009271C IFX_FLOW_PortLinkCfgSet : portIdx 4 IFX_FLOW_PortLinkCfgSet : Duplex value 0 IFX_FLOW_PortLinkCfgSet : Speed value 3 IFX_FLOW_PortLinkCfgSet : Link value 0 IFX_FLOW_PortLinkCfgSet : MII_Mode value 1 switch_utility, RegisterSet, 0xc77, 0xc001, ioctl is called DEBUG> Minor number = 0 DEBUG> IFX_ETHSW_LowLevelCommandSearch[89]: IOC_TYPE=e9, IOC_NR=1 pDrv=80092864, pDrv->pLlHandle=8009271C IFX_FLOW_RegisterSet : addr 00000c77 data 0000c001 switch_utility, RegisterSet, 0xc79, 0xc001, ioctl is called DEBUG> Minor number = 0 DEBUG> IFX_ETHSW_LowLevelCommandSearch[89]: IOC_TYPE=e9, IOC_NR=1 pDrv=80092864, pDrv->pLlHandle=8009271C IFX_FLOW_RegisterSet : addr 00000c79 data 0000c001 switch_utility, RegisterSet, 0xc81, 0xc001, ioctl is called DEBUG> Minor number = 0 DEBUG> IFX_ETHSW_LowLevelCommandSearch[89]: IOC_TYPE=e9, IOC_NR=1 pDrv=80092864, pDrv->pLlHandle=8009271C IFX_FLOW_RegisterSet : addr 00000c81 data 0000c001 MAC Address: 00:06:4e:00:00:01 Interface 1 ip = 192.168.1.1 init_if() ; gConfig.Interface[2].Link_Type is [0] switch_hw_receive[482], SLPID:2 Packet dropped!!! RUNTASK id=1 if_task if0... RUNTASK id=2 if_task if1... RUNTASK id=3 timer_task... Start decompress web imag... Unzipping from 80343EFC to 83F00000 ... done Uncompressed size = 14430 RUNTASK id=4 period_task... RUNTASK id=5 dhcp_daemon... RUNTASK httpd... Starting Multitask... period_task running!!! httpd: listen at 192.168.1.1:80 period_task running 120 switch_hw_receive[482], SLPID:2 Packet dropped!!! period_task running 240 switch_hw_receive[482], SLPID:2 Packet dropped!!! 1 igmp_handler(): checksum error ! 1 igmp_handler(): checksum error ! 1 igmp_handler(): checksum error ! 1 igmp_handler(): checksum error ! 1 igmp_handler(): checksum error ! 1 igmp_handler(): checksum error ! 1 igmp_handler(): checksum error ! 1 igmp_handler(): checksum error ! 1 igmp_handler(): checksum error ! 1 igmp_handler(): checksum error ! 1 igmp_handler(): checksum error ! 1 igmp_handler(): checksum error ! 1 igmp_handler(): checksum error ! period_task running 360 1 igmp_handler(): checksum error ! 1 igmp_handler(): checksum error ! 1 igmp_handler(): checksum error ! 1 igmp_handler(): checksum error ! 1 igmp_handler(): checksum error ! period_task running 480 1 igmp_handler(): checksum error ! 1 igmp_handler(): checksum error ! 1 igmp_handler(): checksum error ! 1 igmp_handler(): checksum error ! 1 igmp_handler(): checksum error ! 1 igmp_handler(): checksum error ! 1 igmp_handler(): checksum error ! 1 igmp_handler(): checksum error ! 1 igmp_handler(): checksum error ! 1 igmp_handler(): checksum error ! period_task running 600 1 igmp_handler(): checksum error ! 1 igmp_handler(): checksum error ! 1 igmp_handler(): checksum error ! 1 igmp_handler(): checksum error ! 1 igmp_handler(): checksum error ! 1 igmp_handler(): checksum error ! period_task running 720 switch_hw_receive[482], SLPID:2 Packet dropped!!! period_task running 840 period_task running 960 period_task running 1080 period_task running 1200 switch_hw_receive[482], SLPID:2 Packet dropped!!! period_task running 1320 period_task running 1440 period_task running 1560


U-Boot 2013.10-openwrt4 (Sep 17 2021 - 07:35:33) arv7520cw22 Board: Arcadyan ARV7520CW22 SoC: Lantiq VRX288 v1.2 CPU: 125 MHz IO: 125 MHz BUS: 125 MHz BOOT: UART w/o EEPROM DRAM: 128 MiB NAND: 128 MiB Using default environment In: serial Out: serial Err: serial Net: ltq-eth arv7520cw22 #


ROM VER: 1.1.4 CFG 06 NAND NAND Read OK U-Boot SPL 2013.10-openwrt4-gba7244a-dirty (Sep 23 2021 - 08:04:13) SPL: initializing SPL: initializing NAND flash SPL: reading image header at page offset 8000 SPL: checking image header at address 81000000 SPL: checking U-Boot image SPL: size 178837, entry 80100000, comp 4 SPL: loading U-Boot to RAM SPL: decompressing U-Boot with LZO SPL: U-Boot entry 80100000 SPL: jumping to U-Boot U-Boot 2013.10-openwrt4-gba7244a-dirty (Sep 23 2021 - 08:04:13) arv7520cw22 Board: Arcadyan ARV7520CW22 SoC: Lantiq VRX288 v1.2 CPU: 500 MHz IO: 250 MHz BUS: 250 MHz BOOT: NAND DRAM: 128 MiB NAND: 128 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: ltq-eth Hit any key to stop autoboot: 0 Loading from nand0, offset 0x100000 ** Unknown image type arv7520cw22 #


COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2021/09/23 08:39
  • by mandrake-lee