User Tools

Site Tools


inbox:linksys:linksys_ea8300

Linksys EA8300

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

The Linksys EA8300 is a MU-MIMO Tri-Band WiFi router, which has one 2.4GHz and two 5GHz WiFi Interfaces, four 1G LAN ports, one 1G WAN port, a USB 3.0 interface and four external antennas. Also, it has Bluetooth 4.1 onboard and a Power-Amplifier for 5GHz. It is powered by an external 12V, 2A power adapter and supports DFS and 256QAM.

OpenWrt support

Not supported, but work in progress

Supporting activities

Based on the LEDE GIT by 07-11-2018, Oliver Welter (verbotenezone) has just begun to add support for the Linksys EA8300 to GIT.

Public discussion on LEDE Forum can be found here.

As you can see in the OpenWrt Bootlog (end of this page), the EA8300 runs with a ipq40xx-qcom_ap-dk04.1-c1 firmware image, but there are many missing drivers. I am currently working on the DTS files and drivers. Experimental firmware will be available soon at https://github.com/Bunkerschild/openwrt

2018-07-31 Oliver Welter contact@verbotene.zone

Hardware highlights

SoC CPU MHz CPU cores Ram Flash Network WLAN-Hardware WLAN2.4 WLAN5.0 USB
Qualcomm IPQ4019 716 4 256 MiB 256 MiB 5x 10/100/1000 Qualcomm Atheros QCA9886 b/g/n a/n/ac 1x 3.0

Hardware

Info

General

Brand Linksys
Model EA8300
Versions V1.0
Device-Type WiFi-Router MU-MIMO Tri-Band
FCC-ID Q87-EA8300
User guide Linksys user guide (PDF)
Stock-Firmware Ver. 1.1.3.184925 - 11/15/2017 - 47.4 MB
SoC Qualcomm IPQ4019
CPU-Cores 4x ARM Cortex A7
CPU-Freq 717 MHz
Flash-Size 256 MB
Flash-Type Macronix MX30LF2G18AC-TI
RAM-Size 256 MB
RAM-Type Nanya NT5CC128M16IP-DI
Power 12V, 2A
WLAN1 type Qualcomm IPQ4019
WLAN1 protocols abgn+ac
WLAN1 antenna non-detachable
WLAN1 MIMO conf. 2×2:2
WLAN1 2.4 GHz 400 Mbps (802.11n @ 40 MHz ch., 256QAM)
WLAN1 5 GHz 867 Mbps (802.11ac @ 80 MHz ch.)
WLAN2 type Qualcomm Atheros QCA9886
WLAN2 protocols an+ac
WLAN2 antenna non-detachable
WLAN2 MIMO conf. 2×2:2
WLAN2 5 GHz 867 Mbps (802.11ac @ 80 MHz ch.)
ETH chip Qualcomm IPQ4019
Switch Qualcomm Atheros QCA8075
LAN ports 4x 10/100/1000
WAN ports 1x 10/100/1000
Bluetooth-Vers. 4.1
Bluetooth chip Qualcomm CSR8811
Power-Amplifier SKY85408-11 for 5 GHz WiFi
USB 1x 3.0

Photos

Opening the case

To open the case, carefully remove the four round rubbers on the back side of EA8300. After that, carefully remove the four Torx-TR screws, which are in each corner, beneeth the rubber feets. Now, you need to rotate the EA8300 again, to the upper side. It is good to have a little and stable plastic spatula, to open the head cover. Take the spatula and put it carefully between the slot, holding EA8300's body and head cover together. Move the spatula against the head cover, so that you can leverage the body from it and turn the spatula all around the EA8300's slot (360 degree), while leveraging as described before. Now, you should can remove the head cover very easily, without brute force.

If you would like to remove the PCB, just remove the antenna plugs on the frontside of the PCB. Lift up the PCB a little bit, on the antenna-plug-side. Now, pull it carefully to get it removed and beware of the WPS switch on the right side of the case.

Serial

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device: After opening the EA8300, you will find the serial port on the right side, in front of the router, marked as J1 on the PCB.

Insert photo of PCB with markings for serial port

WARNING! This has not been tested, yet and might be wrong.

JP1
PIN 1 PIN 2 PIN 3 PIN 4 PIN 5
TXD RXD GND
Serial connection parameters
for Linksys EA8300 V1
115200, 8N1

JTAG

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

Bootlogs

OEM bootlog

Format: Log Type - Time(microsec) - Message - Optional Info Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00108 S - IMAGE_VARIANT_STRING=DAACANAZA S - OEM_IMAGE_VERSION_STRING=CRM S - Boot Config, 0x00000025 S - Reset status Config, 0x00000010 S - Core 0 Frequency, 0 MHz B - 261 - PBL, Start B - 1338 - bootable_media_detect_entry, Start B - 2609 - bootable_media_detect_success, Start B - 2623 - elf_loader_entry, Start B - 4030 - auth_hash_seg_entry, Start B - 6181 - auth_hash_seg_exit, Start B - 74262 - elf_segs_hash_verify_entry, Start B - 196333 - PBL, End B - 196357 - SBL1, Start B - 288383 - pm_device_init, Start D - 7 - pm_device_init, Delta B - 289873 - boot_flash_init, Start D - 87133 - boot_flash_init, Delta B - 381308 - boot_config_data_table_init, Start D - 13973 - boot_config_data_table_init, Delta - (419 Bytes) B - 398033 - clock_init, Start D - 7550 - clock_init, Delta B - 409019 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:6 B - 412432 - sbl1_ddr_set_params, Start B - 417527 - cpr_init, Start D - 2 - cpr_init, Delta B - 421909 - Pre_DDR_clock_init, Start D - 4 - Pre_DDR_clock_init, Delta D - 13170 - sbl1_ddr_set_params, Delta B - 435214 - pm_driver_init, Start D - 2 - pm_driver_init, Delta B - 505015 - sbl1_wait_for_ddr_training, Start D - 28 - sbl1_wait_for_ddr_training, Delta B - 520486 - Image Load, Start D - 144019 - QSEE Image Loaded, Delta - (269176 Bytes) B - 664931 - Image Load, Start D - 2121 - SEC Image Loaded, Delta - (2048 Bytes) B - 675076 - Image Load, Start D - 187408 - APPSBL Image Loaded, Delta - (444319 Bytes) B - 862879 - QSEE Execution, Start D - 56 - QSEE Execution, Delta B - 869115 - SBL1, End D - 674760 - SBL1, Delta S - Flash Throughput, 2085 KB/s (715962 Bytes, 343263 us) S - DDR Frequency, 672 MHz U-Boot 2012.07 [Chaos Calmer 15.05.1,r35193] (Jan 23 2017 - 14:17:23) CBT U-Boot ver: 1.2.9 smem ram ptable found: ver: 1 len: 3 DRAM: 256 MiB machid : 0x8010006 NAND: ID = 9590dac2 Vendor = c2 Device = da ONFI device found SF NAND unsupported id:ff:ff:ff:ffSF: Unsupported manufacturer ff ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0) 256 MiB MMC: qca_mmc: 0 PCI0 Link Intialized In: serial Out: serial Err: serial machid: 8010006 flash_type: 2 Net: MAC0 addr:0:3:7f:ba:db:ad PHY ID1: 0x4d PHY ID2: 0xd0b1 ipq40xx_ess_sw_init done eth0 Updating boot_count ... done Hit any key to stop autoboot: 0 Memory test start, banksize=0x2000000, data size=0x8000, test count per bank=64 Memory test end, lapsed time = 3 seconds The test result is success NAND read: device 0 offset 0x5f80000, size 0x300000 3145728 bytes read: OK ## Booting kernel from FIT Image at 84000000 ... Using 'config@1' configuration Trying 'kernel@1' kernel subimage Description: ARM Linksys Linux-3.14.77 Type: Kernel Image Compression: uncompressed Data Start: 0x840000e4 Data Size: 2545240 Bytes = 2.4 MiB Architecture: ARM OS: Linux Load Address: 0x80208000 Entry Point: 0x80208000 Hash algo: crc32 Hash value: c68b2f21 Hash algo: sha1 Hash value: f62811ae861b055c3d62e863d52edb504d6a003c Verifying Hash Integrity ... crc32+ sha1+ OK ## Flattened Device Tree from FIT Image at 84000000 Using 'config@1' configuration Trying 'fdt@1' FDT blob subimage Description: ARM Linksys Dallas device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x8426d86c Data Size: 38318 Bytes = 37.4 KiB Architecture: ARM Hash algo: crc32 Hash value: 49f16ad6 Hash algo: sha1 Hash value: 8cf30d490b6467bc83d0fff6fbe26973d15b23e2 Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x8426d86c Loading Kernel Image ... OK OK Loading Device Tree to 871e3000, end 871ef5ad ... OK Device nand2 not found! eth0 MAC Address from ART is not valid eth1 MAC Address from ART is not valid Using machid 0x8010006 from environment Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 3.14.77 (root@build-vm) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r35193) ) #1 SMP PREEMPT Mon Nov 6 00:45:28 PST 2017 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: Linksys Dallas WiFi AP router based on Qualcomm AP DK07.1-c1 [ 0.000000] Reserved memory: failed to reserve memory for node 'rsvd1@87000000': base 0x87000000, size 5 MiB [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] PERCPU: Embedded 8 pages/cpu @cfdc8000 s8448 r8192 d16128 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 62208 [ 0.000000] Kernel command line: init=/sbin/init rootfstype=ubifs ubi.mtd=13,2048 root=ubi0:ubifs rootwait rw clk_ignore_unused [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 240764K/250880K available (4962K kernel code, 415K rwdata, 1664K rodata, 208K init, 325K bss, 10116K reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0880d1c (6628 kB) [ 0.000000] .init : 0xc0881000 - 0xc08b5100 ( 209 kB) [ 0.000000] .data : 0xc08b6000 - 0xc091df34 ( 416 kB) [ 0.000000] .bss : 0xc091df34 - 0xc096f5dc ( 326 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] Architected cp15 timer(s) running at 48.00MHz (virt). [ 0.000008] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 2863311552512ns [ 0.000018] Switching to timer-based delay loop [ 0.000340] Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000) [ 0.000359] pid_max: default: 32768 minimum: 301 [ 0.000628] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000642] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.012216] CPU: Testing write buffer coherency: ok [ 0.012566] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.012634] Setting up static identity map for 0x802137b0 - 0x80213808 [ 0.090613] CPU1: Booted secondary processor [ 0.090658] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.110630] CPU2: Booted secondary processor [ 0.110670] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.130644] CPU3: Booted secondary processor [ 0.130680] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.130816] Brought up 4 CPUs [ 0.130858] SMP: Total of 4 processors activated (384.00 BogoMIPS). [ 0.130868] CPU: All CPU(s) started in SVC mode. [ 0.141053] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.141426] pinctrl core: initialized pinctrl subsystem [ 0.141858] regulator-dummy: no parameters [ 0.142521] NET: Registered protocol family 16 [ 0.144083] DMA: preallocated 2048 KiB pool for atomic coherent allocations [ 0.144607] cpuidle: using governor ladder [ 0.144619] cpuidle: using governor menu [ 0.154962] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 1 [ 0.154970] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 2 [ 0.154978] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 3 [ 0.154982] hw-breakpoint: CPU 2 failed to disable vector catch [ 0.155014] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 0 [ 0.155100] [ 0.155100] Version Rollback Feature Disabled [ 0.158514] i2c-msm-v2 78b7000.i2c: probing driver i2c-msm-v2 [ 0.159298] sps:sps is ready. [ 0.165682] bio: create slab <bio-0> at 0 [ 0.167354] SD0 VccQ: 1800 <--> 3000 mV [ 0.167849] SCSI subsystem initialized [ 0.168539] msm_bus_fabric_init_driver [ 0.168698] msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100 [ 0.168715] msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100 [ 0.168734] msm_bus_device 580000.ad-hoc-bus: Failed to get bus clk for bus4096 ctx1 [ 0.168776] msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100 [ 0.168791] msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100 [ 0.168808] msm_bus_device 580000.ad-hoc-bus: Failed to get bus clk for bus1024 ctx1 [ 0.194797] Bluetooth: Core ver 2.18 [ 0.194869] NET: Registered protocol family 31 [ 0.194879] Bluetooth: HCI device and connection manager initialized [ 0.194896] Bluetooth: HCI socket layer initialized [ 0.194911] Bluetooth: L2CAP socket layer initialized [ 0.194979] Bluetooth: SCO socket layer initialized [ 0.195179] 80000.qcom,pcie supply vreg-3.3 not found, using dummy regulator [ 0.195243] 80000.qcom,pcie supply vreg-1.8 not found, using dummy regulator [ 0.195302] 80000.qcom,pcie supply vreg-0.9 not found, using dummy regulator [ 0.195363] 80000.qcom,pcie supply gdsc-vdd not found, using dummy regulator [ 0.290519] msm_pcie_enable: msm_pcie_enable: PCIe: trigger the reset of endpoint of RC0. [ 0.300473] msm_pcie_enable: msm_pcie_enable: PCIe RC0 PHY is ready! [ 0.320474] msm_pcie_enable: msm_pcie_enable: PCIe: Release the reset of endpoint of RC0. [ 0.460611] msm_pcie_enable: msm_pcie_enable: PCIe RC0 link initialized [ 0.460870] PCI host bridge to bus 0000:00 [ 0.460894] pci_bus 0000:00: root bus resource [io 0x40200000-0x402fffff] [ 0.460910] pci_bus 0000:00: root bus resource [mem 0x40300000-0x40ffffff] [ 0.460925] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.461006] msm_pcie_oper_conf: msm_pcie_oper_conf: Read of RC0 0:0x00 + 0x0014[4] is all FFs [ 0.461426] PCI: bus0: Fast back to back transfers disabled [ 0.461444] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.461714] msm_pcie_oper_conf: msm_pcie_oper_conf: Read of RC0 1:0x00 + 0x0014[4] is all FFs [ 0.462269] PCI: bus1: Fast back to back transfers disabled [ 0.462363] msm_pcie_oper_conf: msm_pcie_oper_conf: Read of RC0 0:0x00 + 0x0028[4] is all FFs [ 0.462398] pci 0000:00:00.0: BAR 8: assigned [mem 0x40400000-0x405fffff] [ 0.462417] pci 0000:00:00.0: BAR 0: assigned [mem 0x40300000-0x40300fff 64bit] [ 0.462448] pci 0000:01:00.0: BAR 0: assigned [mem 0x40400000-0x405fffff 64bit] [ 0.462488] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.462509] pci 0000:00:00.0: bridge window [mem 0x40400000-0x405fffff] [ 0.462532] msm_pcie_probe: msm_pcie_probe: RC0 is enabled in bootup [ 0.462824] Switched to clocksource arch_sys_counter [ 0.464641] NET: Registered protocol family 2 [ 0.465885] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.465933] TCP bind hash table entries: 2048 (order: 2, 16384 bytes) [ 0.465983] TCP: Hash tables configured (established 2048 bind 2048) [ 0.466041] TCP: reno registered [ 0.466058] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.466088] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.466431] NET: Registered protocol family 1 [ 0.467224] hw perfevents: enabled with ARMv7 Cortex-A7 PMU driver, 5 counters available [ 0.468642] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.478162] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.478177] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.479142] msgmni has been set to 470 [ 0.480801] Key type asymmetric registered [ 0.480817] Asymmetric key parser 'x509' registered [ 0.480853] io scheduler noop registered [ 0.480863] io scheduler deadline registered (default) [ 0.481782] tcsr 194b000.tcsr: setting usb hs phy mode select = e700e7 [ 0.481851] tcsr 1953000.ess_tcsr: setting ess interface select = 0 [ 0.481922] tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000 [ 0.481979] tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222 [ 0.482415] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.483522] msm_serial_hsl_probe: detected port #0 (ttyMSM0) [ 0.483563] msm_serial_hsl_probe: Bus scaling is disabled [ 0.483714] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 139, base_baud = 115200) is a MSM [ 0.483788] msm_hsl_console_setup: console setup on port #0 [ 1.288005] console [ttyMSM0] enabled [ 1.292089] msm_serial_hsl_init: driver initialized [ 1.297069] uart_tx_gpio is not available [ 1.300494] uart_rx_gpio is not available [ 1.304528] uart_cts_gpio is not available [ 1.308565] uart_rfr_gpio is not available [ 1.312648] Wakeup irq not specified. [ 1.316316] BLSP UART: Bus scaling is disabled. [ 1.320998] sps: BAM device 0x07884000 is not registered yet. [ 1.326562] sps:BAM 0x07884000 is registered. [ 1.331015] 78b0000.uart: ttyQHS0 at MMIO 0x78b0000 (irq = 140, base_baud = 460800) is a MSM HS UART [ 1.340358] qca_serial_hs module loaded [ 1.345948] sps: BAM device 0x07984000 is not registered yet. [ 1.350669] sps:BAM 0x07984000 is registered. [ 1.354871] msm_nand_bam_init: msm_nand_bam_init: BAM device registered: bam_handle 0xcf0b4e00 [ 1.363746] sps:BAM 0x07984000 (va:0xd0a60000) enabled: ver:0x19, number of pipes:7 [ 1.371450] msm_nand_version_check: nand_major:1, nand_minor:4, qpic_major:1, qpic_minor:4 [ 1.379532] msm_nand_scan: missing page size info - extract from NAND ID [ 1.386183] msm_nand_scan: NAND Id: 0x9590dac2 Buswidth: 8Bits Density: 256 MByte [ 1.393646] msm_nand_scan: pagesize: 2048 Erasesize: 131072 oobsize: 64 (in Bytes) [ 1.401180] msm_nand_scan: BCH ECC: 4 Bit [ 1.405198] msm_nand_scan: CFG0: 0x2a0408c0, CFG1: 0x0804745c [ 1.405198] RAWCFG0: 0x280420c0, RAWCFG1: 0x0005045d [ 1.405198] ECCBUFCFG: 0x00000203, ECCBCHCFG: 0x42040700 [ 1.405198] BAD BLOCK BYTE: 0x000001d1 [ 1.427927] 16 ofpart partitions found on MTD device 7980000.qcom,nand [ 1.434358] Creating 16 MTD partitions on "7980000.qcom,nand": [ 1.440170] 0x000000000000-0x000000100000 : "0:SBL1" [ 1.446988] 0x000000100000-0x000000200000 : "0:MIBIB" [ 1.452767] 0x000000200000-0x000000300000 : "0:QSEE" [ 1.458501] 0x000000300000-0x000000380000 : "0:CDT" [ 1.463790] 0x000000380000-0x000000400000 : "0:APPSBLENV" [ 1.469587] 0x000000400000-0x000000480000 : "0:ART" [ 1.474916] 0x000000480000-0x000000680000 : "0:APPSBL" [ 1.481401] 0x000000680000-0x000000700000 : "u_env" [ 1.486637] 0x000000700000-0x000000740000 : "s_env" [ 1.491668] 0x000000740000-0x000000780000 : "devinfo" [ 1.496942] 0x000000780000-0x000005f80000 : "kernel" [ 1.562686] 0x000000a80000-0x000005f80000 : "rootfs" [ 1.626376] mtd: device 11 (rootfs) set to be root filesystem [ 1.631092] 0x000005f80000-0x00000b780000 : "alt_kernel" [ 1.698280] 0x000006280000-0x00000b780000 : "alt_rootfs" [ 1.762369] 0x00000b780000-0x00000b880000 : "sysdiag" [ 1.768244] 0x00000b880000-0x00000ff00000 : "syscfg" [ 1.821806] msm_nand_probe: NANDc phys addr 0x7980000, BAM phys addr 0x7984000, BAM IRQ 133 [ 1.829151] msm_nand_probe: Allocated DMA buffer at virt_addr 0xd0a7b000, phys_addr 0x8f0ba000 [ 1.839739] sps:BAM 0x07884000 (va:0xd0b40000) enabled: ver:0x19, number of pipes:12 [ 1.846758] m25p80 spi0.0: Failed to find sector-size [ 1.863725] libphy: ipq40xx_mdio: probed [ 1.870098] ipq40xx-mdio 90000.mdio: ipq40xx-mdio driver was registered [ 1.875772] tun: Universal TUN/TAP device driver, 1.6 [ 1.880712] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 1.887028] PPP generic driver version 2.4.2 [ 1.891297] PPP BSD Compression module registered [ 1.895838] PPP Deflate Compression module registered [ 1.900854] NET: Registered protocol family 24 [ 1.905296] i2c /dev entries driver [ 1.910332] Bluetooth: HCI UART driver ver 2.2 [ 1.913769] Bluetooth: HCI H4 protocol initialized [ 1.918514] Bluetooth: HCI BCSP protocol initialized [ 1.925468] hidraw: raw HID events driver (C) Jiri Kosina [ 1.930896] u32 classifier [ 1.932567] input device check on [ 1.936256] Netfilter messages via NETLINK v0.30. [ 1.940917] nfnl_acct: registering with nfnetlink. [ 1.945761] nf_conntrack version 0.5.0 (3761 buckets, 15044 max) [ 1.952248] ctnetlink v0.93: registering with nfnetlink. [ 1.957010] nf_conntrack_rtsp v0.7 loading [ 1.961116] ip_set: protocol 6 [ 1.964280] gre: GRE over IPv4 demultiplexor driver [ 1.968941] ip_gre: GRE over IPv4 tunneling driver [ 1.975287] nf_nat_rtsp v0.7 loading [ 1.977866] ip_tables: (C) 2000-2006 Netfilter Core Team [ 1.983408] TCP: cubic registered [ 1.987170] NET: Registered protocol family 10 [ 1.992517] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 1.997270] sit: IPv6 over IPv4 tunneling driver [ 2.003447] NET: Registered protocol family 17 [ 2.006988] Bridge firewalling registered [ 2.010858] Ebtables v2.0 registered [ 2.014688] Bluetooth: RFCOMM TTY layer initialized [ 2.019291] Bluetooth: RFCOMM socket layer initialized [ 2.024449] Bluetooth: RFCOMM ver 1.11 [ 2.028135] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 2.033440] Bluetooth: BNEP filters: protocol multicast [ 2.038641] Bluetooth: BNEP socket layer initialized [ 2.043633] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 2.049491] Bluetooth: HIDP socket layer initialized [ 2.054498] l2tp_core: L2TP core driver, V2.0 [ 2.058783] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 2.063560] l2tp_netlink: L2TP netlink interface [ 2.068170] 8021q: 802.1Q VLAN Support v1.8 [ 2.072476] Registering SWP/SWPB emulation handler [ 2.078444] SD0 VccQ: disabling [ 2.080553] regulator-dummy: disabling [ 2.084699] UBI: attaching mtd13 to ubi0 [ 2.441084] UBI: scanning is finished [ 2.450701] UBI: attached mtd13 (name "alt_rootfs", size 85 MiB) to ubi0 [ 2.456404] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 2.463155] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 2.469821] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 2.476696] UBI: good PEBs: 680, bad PEBs: 0, corrupted PEBs: 0 [ 2.482582] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 2.489717] UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 2086578551 [ 2.498745] UBI: available PEBs: 0, total reserved PEBs: 680, PEBs reserved for bad PEB handling: 40 [ 2.507881] UBI: background thread "ubi_bgt0d" started, PID 73 [ 2.508698] input: gpio_keys.7 as /devices/soc.0/gpio_keys.7/input/input0 [ 2.508946] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 2.512477] clk: Not disabling unused clocks [ 2.532370] UBIFS: background thread "ubifs_bgt0_0" started, PID 75 [ 2.578568] UBIFS: mounted UBI device 0, volume 0, name "ubifs" [ 2.583498] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 2.592575] UBIFS: FS size: 79360000 bytes (75 MiB, 625 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs) [ 2.602223] UBIFS: reserved for root: 0 bytes (0 KiB) [ 2.607262] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 2EAC459E-9655-4413-B027-D3005B5F5761, small LPT model [ 2.619597] VFS: Mounted root (ubifs filesystem) on device 0:11. [ 2.624905] Freeing unused kernel memory: 208K (c0881000 - c08b5000) ********************************************************************************* _ _ __ _ __ _____ __ __ _____ | | | || \ | | / // ____]\ \ / // ____]TM | | | || \ | | / /| (___ \ V /| (____ | | | || |\ \| |\ \ \____ \ \ / \____ \ | |_____ | || | \ | \ \ ____) | | | ____) | |_______||_||_| \__| \_\[____ / |_| [_____/ (c) 2013 Belkin International, Inc. and/or its affiliates. All rights reserved. Booting dallas (firmware version 1.1.3.184925) ********************************************************************************* [utopia][init] System Initialization [utopia][init] Creating /proc [utopia][init] Creating /sys [utopia][init] Creating /dev [utopia][init] Creating /tmp [utopia][init] Allocating 60M for /tmp [utopia][init] Prepairing /dev/pts [utopia][init] Setting /tmp and /var permissions [utopia][init] Starting udev.. [ 3.002265] UBIFS: background thread "ubifs_bgt0_0" stops Attempting mount of ubifs syscfg partition UBI device number 1, total 564 LEBs (71614464 bytes, 68.3 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB) [utopia][init] Using persistent syscfg data from /var/config/syscfg [utopia][init] Starting system logging [utopia][init] Starting sysevent subsystem [utopia][init] Enabling DesignWare USB3 DRD Core drivers [utopia][init] Loading QCA Ethernet, NSS and GMAC drivers net.netfilter.nf_conntrack_acct = 1 [utopia][init] Late loading usb drivers [utopia][init] Setting any unset system values to default [utopia][init] no persistence config file (/var/config/pstcfg) found setting up MAC addresses for all interface based on 24:F5:A2:06:5B:80 NTP Servers do not need to be updated checking for interactive script start up... Updating BootCount Page[40]:14000 ... Done attempting to sync sysinfo.cgi auth credentials [utopia][init] Loading Buttons drivers [utopia][init] Load WiFi cal data from MTD(mtd5) to FS. [utopia][init] Setup link to WiFi firmware and board data (EU) [utopia][init] Using EU region for WiFi firmware and board data NSS Auto scaling disabled inserting fpbypass.ko for QCA Sat Jul 28 20:50:00 UTC 2018 dallas login: wan, sysevent received: wan-start=NULL Guest access control is up Usage: link_aggregation [ link_aggregation-start | link_aggregation-stop | link_aggregation-restart ] SSDK Init OK! operate done. wifi, sysevent received: lan-started (Sat Jul 28 21:50:05 CET 2018) Lighttpd Model Base: EA8300 Generating Rainier lighttpd config Build temporary www configuration directory: wifi, service_start() $1$1bxubP3Z$zhSRiG0zO74sDlifh1FgQ/ Registering Service myrouter._http._tcp.local port 80 Power cycle Ethernet ports. Got a reply for myrouter._http._tcp.local.: Name now registered and active [utopia][init] Loading GMAC and WLAN drivers [utopia][init] Creating wifi devices ath0 ath1 ath10 wifi, wifi_physical_start(ath0) wifi, setting obss rssi threshold (ath0) Invalid command : obss_rx_rssi_th Auto channel Invalid command : acs_2g_allchan wifi, wifi_virtual_start(ath0) wifi, wifi_user_start(ath0) Not ready for JNAP. Sleeping for 15 seconds... wifi_user, ath0 TxBF enabled wifi, primary AP: ath0 is up wifi, wifi_guest_start(ath0) ath2 wifi_user, ath2 TxBF enabled wifi, guest AP: ath2 is up wifi, wifi_physical_start(ath1) [utopia] Not setting ppp_clamp_mtu wifi, setting obss rssi threshold (ath1) Invalid command : obss_rx_rssi_th Auto channel Following channels are blocked from Channel selection algorithm [52] [56] [60] [64] wifi, wifi_virtual_start(ath1) wifi, wifi_user_start(ath1) wifi_user, ath1 TxBF enabled wifi_user, ath1 MU-MIMO enabled wifi, primary AP: ath1 is up SSDK Init OK! operate done. wifi, wifi_guest_start(ath1) RTNETLINK answers: Device or resource busy ath3 wifi_user, ath3 TxBF enabled wifi_user, ath3 MU-MIMO enabled wifi, guest AP: ath3 is up wifi, wifi_physical_start(ath10) wifi, setting obss rssi threshold (ath10) Invalid command : obss_rx_rssi_th Auto channel wifi, wifi_virtual_start(ath10) wifi, wifi_user_start(ath10) wifi_user, ath10 TxBF enabled wifi_user, ath10 MU-MIMO enabled wifi, primary AP: ath10 is up wifi, wifi_guest_start(ath10) wifi, guest ath6 is disabled, do not start wifi guest wifi, start_hostapd() Configuration file: /tmp/hostapd-ath0.conf Configuration file: /tmp/hostapd-ath1.conf Configuration file: /tmp/hostapd-ath10.conf ath0: Could not connect to kernel driver Using interface ath0 with hwaddr 24:f5:a2:06:5b:81 and ssid "Linksys13295" random: Cannot read from /dev/random: Resource temporarily unavailable random: Only 0/20 bytes of strong random data available from /dev/random random: Not enough entropy pool available for secure operations WPA: Not enough entropy in random pool for secure operations - update keys later when the first station connects ath0: interface state UNINITIALIZED->ENABLED ath0: AP-ENABLED ath1: Could not connect to kernel driver Using interface ath1 with hwaddr 24:f5:a2:06:5b:82 and ssid "Linksys13295" random: Cannot read from /dev/random: Resource temporarily unavailable random: Only 0/20 bytes of strong random data available from /dev/random random: Not enough entropy pool available for secure operations WPA: Not enough entropy in random pool for secure operations - update keys later when the first station connects ath1: interface state UNINITIALIZED->ENABLED ath1: AP-ENABLED ath10: Could not connect to kernel driver Using interface ath10 with hwaddr 24:f5:a2:06:5b:83 and ssid "Linksys13295" ===>RESET dallas usb power random: Cannot read from /dev/random: Resource temporarily unavailable random: Only 0/20 bytes of strong random data available from /dev/random random: Not enough entropy pool available for secure operations WPA: Not enough entropy in random pool for secure operations - update keys later when the first station connects ath10: interface state UNINITIALIZED->ENABLED ath10: AP-ENABLED Restarting nfqrecv service... fastpath, sysevent received: qos_enabled wifi, start_lbd() starting daemon [utopia] Not setting ppp_clamp_mtu on dslite protocol wan, sysevent received: phylink_wan_state=down [fw.sh] fwup_checked_after_boot: 0 [fwupd] status details:"ERROR: Connecting server" [fw.sh] fwup_forced_update: 0 Starting smbd ... [fw.sh] fwup_checked_after_boot: 0 [fwupd] status details:"ERROR: Connecting server" [fw.sh] fwup_forced_update: 0


OpenWrt bootlog (TFTP Image with test kernel)

Format: Log Type - Time(microsec) - Message - Optional Info Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00108 S - IMAGE_VARIANT_STRING=DAACANAZA S - OEM_IMAGE_VERSION_STRING=CRM S - Boot Config, 0x00000025 S - Reset status Config, 0x00000010 S - Core 0 Frequency, 0 MHz B - 261 - PBL, Start B - 1339 - bootable_media_detect_entry, Start B - 2609 - bootable_media_detect_success, Start B - 2623 - elf_loader_entry, Start B - 4030 - auth_hash_seg_entry, Start B - 6181 - auth_hash_seg_exit, Start B - 74261 - elf_segs_hash_verify_entry, Start B - 196330 - PBL, End B - 196354 - SBL1, Start B - 288379 - pm_device_init, Start D - 7 - pm_device_init, Delta B - 289869 - boot_flash_init, Start D - 87156 - boot_flash_init, Delta B - 381328 - boot_config_data_table_init, Start D - 13978 - boot_config_data_table_init, Delta - (419 Bytes) B - 398058 - clock_init, Start D - 7586 - clock_init, Delta B - 409079 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:6 B - 412492 - sbl1_ddr_set_params, Start B - 417586 - cpr_init, Start D - 2 - cpr_init, Delta B - 421969 - Pre_DDR_clock_init, Start D - 4 - Pre_DDR_clock_init, Delta D - 13171 - sbl1_ddr_set_params, Delta B - 435273 - pm_driver_init, Start D - 2 - pm_driver_init, Delta B - 505082 - sbl1_wait_for_ddr_training, Start D - 28 - sbl1_wait_for_ddr_training, Delta B - 520564 - Image Load, Start D - 144019 - QSEE Image Loaded, Delta - (269176 Bytes) B - 665009 - Image Load, Start D - 2121 - SEC Image Loaded, Delta - (2048 Bytes) B - 675150 - Image Load, Start D - 187397 - APPSBL Image Loaded, Delta - (444319 Bytes) B - 862942 - QSEE Execution, Start D - 56 - QSEE Execution, Delta B - 869146 - SBL1, End D - 674901 - SBL1, Delta S - Flash Throughput, 2085 KB/s (715962 Bytes, 343256 us) S - DDR Frequency, 672 MHz U-Boot 2012.07 [Chaos Calmer 15.05.1,r35193] (Jan 23 2017 - 14:17:23) CBT U-Boot ver: 1.2.9 smem ram ptable found: ver: 1 len: 3 DRAM: 256 MiB machid : 0x8010006 NAND: ID = 9590dac2 Vendor = c2 Device = da ONFI device found SF NAND unsupported id:ff:ff:ff:ffSF: Unsupported manufacturer ff ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0) 256 MiB MMC: qca_mmc: 0 PCI0 Link Intialized In: serial Out: serial Err: serial machid: 8010006 flash_type: 2 Net: MAC0 addr:0:3:7f:ba:db:ad PHY ID1: 0x4d PHY ID2: 0xd0b1 ipq40xx_ess_sw_init done eth0 Updating boot_count ... done Hit any key to stop autoboot: 0 (IPQ40xx) # setenv ipaddr 192.168.1.1 (IPQ40xx) # setenv serverip 192.168.1.6 (IPQ40xx) # tftp openwrt-ipq40xx-qcom_ap-dk04.1-c1-initramfs-fit-uImage.itb eth0 PHY0 Down Speed :10 Half duplex eth0 PHY1 Down Speed :10 Half duplex eth0 PHY2 Down Speed :10 Half duplex eth0 PHY3 up Speed :100 Full duplex eth0 PHY4 Down Speed :10 Half duplex Using eth0 device TFTP from server 192.168.1.6; our IP address is 192.168.1.1 Filename 'openwrt-ipq40xx-qcom_ap-dk04.1-c1-initramfs-fit-uImage.itb'. Load address: 0x84000000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# #### done Bytes transferred = 6736896 (66cc00 hex) (IPQ40xx) # bootm ## Booting kernel from FIT Image at 84000000 ... Using 'config@1' configuration Trying 'kernel@1' kernel subimage Description: ARM OpenWrt Linux-4.14.59 Type: Kernel Image Compression: gzip compressed Data Start: 0x840000e4 Data Size: 6720210 Bytes = 6.4 MiB Architecture: ARM OS: Linux Load Address: 0x80208000 Entry Point: 0x80208000 Hash algo: crc32 Hash value: 7d5e1f1c Hash algo: sha1 Hash value: f7c24d295cf139f0fcb742ecbf8c13cbb7c4563e Verifying Hash Integrity ... crc32+ sha1+ OK ## Flattened Device Tree from FIT Image at 84000000 Using 'config@1' configuration Trying 'fdt@1' FDT blob subimage Description: ARM OpenWrt qcom_ap-dk04.1-c1 device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x84668cf4 Data Size: 14809 Bytes = 14.5 KiB Architecture: ARM Hash algo: crc32 Hash value: d9fa7caf Hash algo: sha1 Hash value: 169360b07ecbe32963874badfa0d1ea3609266be Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x84668cf4 Uncompressing Kernel Image ... OK Loading Device Tree to 871e8000, end 871ee9d8 ... OK Device nand2 not found! eth0 MAC Address from ART is not valid eth1 MAC Address from ART is not valid Using machid 0x8010006 from environment Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.14.59 (olli@athena) (gcc version 7.3.0 (OpenWrt 8 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instructie [ 0.000000] OF: fdt: Machine model: Qualcomm Technologies, Inc. IPQ40xx/AP-D1 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] random: get_random_bytes called from start_kernel+0x88/0x3c0 wit0 [ 0.000000] percpu: Embedded 15 pages/cpu @cfdb1000 s29260 r8192 d23988 u6140 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64512 [ 0.000000] Kernel command line: [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 242772K/260096K available (4180K kernel code, 137K rwdat) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0715100 (5173 kB) [ 0.000000] .init : 0xc0900000 - 0xc1100000 (8192 kB) [ 0.000000] .data : 0xc1100000 - 0xc1122540 ( 138 kB) [ 0.000000] .bss : 0xc1124000 - 0xc11612b4 ( 245 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] arch_timer: cp15 timer(s) running at 48.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycless [ 0.000008] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 4398s [ 0.000022] Switching to timer-based delay loop, resolution 20ns [ 0.000213] Calibrating delay loop (skipped), value calculated using timer f) [ 0.000230] pid_max: default: 32768 minimum: 301 [ 0.000357] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000374] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000942] CPU: Testing write buffer coherency: ok [ 0.001539] Setting up static identity map for 0x80300000 - 0x80300060 [ 0.001662] Hierarchical SRCU implementation. [ 0.002226] smp: Bringing up secondary CPUs ... [ 0.004637] smp: Brought up 1 node, 4 CPUs [ 0.004654] SMP: Total of 4 processors activated (384.00 BogoMIPS). [ 0.004662] CPU: All CPU(s) started in SVC mode. [ 0.008040] VFP support v0.3: implementor 41 architecture 2 part 30 variant 5 [ 0.008188] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ms [ 0.008211] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.008384] pinctrl core: initialized pinctrl subsystem [ 0.009210] NET: Registered protocol family 16 [ 0.009449] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.010509] cpuidle: using governor ladder [ 0.010550] cpuidle: using governor menu [ 0.022722] usbcore: registered new interface driver usbfs [ 0.022792] usbcore: registered new interface driver hub [ 0.022870] usbcore: registered new device driver usb [ 0.022925] pps_core: LinuxPPS API ver. 1 registered [ 0.022934] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giom> [ 0.022960] PTP clock support registered [ 0.023988] clocksource: Switched to clocksource arch_sys_counter [ 0.024752] NET: Registered protocol family 2 [ 0.025319] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.025360] TCP bind hash table entries: 2048 (order: 2, 16384 bytes) [ 0.025411] TCP: Hash tables configured (established 2048 bind 2048) [ 0.025507] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.025542] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.025731] NET: Registered protocol family 1 [ 0.113582] No memory allocated for crashlog [ 0.113733] workingset: timestamp_bits=30 max_order=16 bucket_order=0 [ 0.116905] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.116922] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORI. [ 0.121777] io scheduler noop registered [ 0.121795] io scheduler deadline registered (default) [ 0.124445] bam-dma-engine 8e04000.dma: num-channels unspecified in dt [ 0.124463] bam-dma-engine 8e04000.dma: num-ees unspecified in dt [ 0.125781] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.126301] msm_serial 78af000.serial: msm_serial: detected port #0 [ 0.126346] msm_serial 78af000.serial: uartclk = 1843200 [ 0.126395] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 26, base_baud =M [ 0.126419] msm_serial: console setup on port #0 [ 0.609337] console [ttyMSM0] enabled [ 0.614322] msm_serial 78b0000.serial: msm_serial: detected port #1 [ 0.617585] msm_serial 78b0000.serial: uartclk = 48000000 [ 0.623674] 78b0000.serial: ttyMSM1 at MMIO 0x78b0000 (irq = 27, base_baud =M [ 0.629423] msm_serial: driver initialized [ 0.641657] loop: module loaded [ 0.643240] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xda [ 0.644855] nand: Macronix MX30LF2G18AC [ 0.651407] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB si4 [ 0.656209] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64 [ 0.663307] m25p80 spi0.0: unrecognized JEDEC id bytes: ff, ff, ff [ 0.670630] libphy: Fixed MDIO Bus: probed [ 0.675954] i2c /dev entries driver [ 0.680088] i2c_qup 78b7000.i2c: using default clock-frequency 100000 [ 0.712785] NET: Registered protocol family 10 [ 0.716902] Segment Routing with IPv6 [ 0.717002] NET: Registered protocol family 17 [ 0.720260] 8021q: 802.1Q VLAN Support v1.8 ▒[ 0.745575] Freeing unused kernel memory: 8192Ker [ 0.811408] init: Console is alive [ 0.811591] init: - watchdog - [ 0.822673] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 0.825558] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.832062] SCSI subsystem initialized [ 0.841171] ehci-platform: EHCI generic platform driver [ 0.864908] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.867021] ohci-platform: OHCI generic platform driver [ 1.167230] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 1.167295] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus n1 [ 1.171844] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f665 hci version 0x100 [ 1.179268] xhci-hcd xhci-hcd.0.auto: irq 29, io mem 0x08a00000 [ 1.188532] hub 1-0:1.0: USB hub found [ 1.193790] hub 1-0:1.0: 1 port detected [ 1.197924] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 1.201664] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus n2 [ 1.206989] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 1.214671] usb usb2: We don't know the algorithms for LPM for this host, di. [ 1.221830] hub 2-0:1.0: USB hub found [ 1.229514] hub 2-0:1.0: 1 port detected [ 1.233516] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 1.237122] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus n3 [ 1.242600] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f665 hci version 0x100 [ 1.249990] xhci-hcd xhci-hcd.1.auto: irq 30, io mem 0x06000000 [ 1.259202] hub 3-0:1.0: USB hub found [ 1.264552] hub 3-0:1.0: 1 port detected [ 1.268601] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 1.272417] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus n4 [ 1.277725] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 1.285393] usb usb4: We don't know the algorithms for LPM for this host, di. [ 1.292543] hub 4-0:1.0: USB hub found [ 1.300253] hub 4-0:1.0: config failed, hub doesn't have any ports! (err -19) [ 1.305453] kmodloader: done loading kernel modules from /etc/modules-boot.d* [ 1.314289] init: - preinit - [ 1.460416] random: jshn: uninitialized urandom read (4 bytes read) [ 1.494998] random: jshn: uninitialized urandom read (4 bytes read) [ 1.506408] random: jshn: uninitialized urandom read (4 bytes read) /bin/board_detect: line 12: Unsupported: not found Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 4.763182] procd: - early - [ 4.763311] procd: - watchdog - [ 5.395127] procd: - watchdog - [ 5.397838] procd: - ubus - [ 5.409351] urandom_read: 5 callbacks suppressed [ 5.409362] random: ubusd: uninitialized urandom read (4 bytes read) [ 5.459896] random: ubusd: uninitialized urandom read (4 bytes read) [ 5.471215] procd: - init - Please press Enter to activate this console. [ 5.593927] kmodloader: loading kernel modules from /etc/modules.d/* [ 5.597918] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 5.997919] Loading modules backported from Linux version wt-2017-11-01-0-gf0 [ 5.997954] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d [ 6.006248] ip_tables: (C) 2000-2006 Netfilter Core Team [ 6.358200] nf_conntrack version 0.5.0 (4096 buckets, 16384 max) [ 6.569404] xt_time: kernel timezone is -0000 [ 6.767816] PPP generic driver version 2.4.2 [ 6.768723] NET: Registered protocol family 24 [ 6.782810] kmodloader: done loading kernel modules from /etc/modules.d/* BusyBox v1.28.4 () built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt SNAPSHOT, r7707-af9731832b ----------------------------------------------------- === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. -------------------------------------------------- root@OpenWrt:/#


Notes

Tags

inbox/linksys/linksys_ea8300.txt · Last modified: 2018/07/31 16:18 by verbotenezone