Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| docs:user-guide:failsafe_and_factory_reset [2017/05/03 15:26] – [Entering failsafe mode] add link to Openwrt failsafe pge hnyman | docs:guide-user:troubleshooting:failsafe_and_factory_reset [2024/07/11 08:43] – [Fixing your settings] palbiez | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== Failsafe | + | ====== Failsafe |
| - | //LEDE// allows you to boot into a **failsafe | + | OpenWrt offers several ways to "start over" with your router: |
| + | | ||
| + | * **[[docs: | ||
| + | * **[[docs: | ||
| - | Failsafe mode **cannot**, however, fix more deeply rooted problems like faulty hardware or a broken kernel. It is similar | + | ===== Failsafe mode ===== |
| + | OpenWrt allows you to boot into a **failsafe mode** that overrides its current configuration. | ||
| + | If your device becomes inaccessible, e.g. after a configuration error, then failsafe mode is there to help you out. | ||
| + | When you reboot in failsafe mode, the device starts up in a basic operating state, with a few hard coded defaults, and you can begin to fix the problem manually. | ||
| - | **Caveat:** Failsafe mode is only available if you have installed firmware from a SquashFS | + | Failsafe mode can be triggered by pressing (almost any) button on the device shortly after powering it on. |
| + | Each router is unique, but OpenWrt watches for a WPS, Reset, or other button press. | ||
| + | |||
| + | Failsafe mode **cannot**, however, fix more deeply rooted problems like faulty hardware or a broken kernel. | ||
| + | It is similar to a reset, however with failsafe, you can access your device and restore settings if desired, whereas a reset would just wipe everything. | ||
| + | |||
| + | **Caveat:** Failsafe mode is only available if you have installed firmware from a Squashfs | ||
| + | To verify whether your device has the SquashFS root partition, check for " | ||
| + | |||
| + | <code bash> | ||
| + | grep squash / | ||
| + | </ | ||
| + | |||
| + | The terminal should return something similar to this: | ||
| < | < | ||
| - | grep squash | + | /dev/root /rom squashfs ro,relatime 0 0 |
| </ | </ | ||
| + | |||
| + | |||
| ==== Entering failsafe mode ==== | ==== Entering failsafe mode ==== | ||
| + | Failsafe mode starts the router with the IP address 192.168.1.1, | ||
| + | DHCP and wireless connectivity. | ||
| + | You will need to set your PC to a static address on the same subnet | ||
| + | (e.g., 192.168.1.10) and connect via Ethernet. | ||
| + | Sometimes you need to connect to a specific network port of your router | ||
| + | to get connectivity. | ||
| + | **Try the LAN1 port first.** | ||
| + | DSA devices frequently enable [[https:// | ||
| - | Make sure you use a wired connection, since the failsafe | + | On most routers, OpenWrt will blink an LED (usually " |
| + | Early in the boot cycle, OpenWrt watches for a button press (any button) | ||
| + | inside a specific two second window to indicate that it should enter failsafe | ||
| - | On most routers, LEDE will blink a LED (usually " | + | **To enter failsafe mode, follow one of the procedures listed below:** |
| - | There are three different (power) LED blinking speeds during boot for most of the routers: | + | **Simplest - recommended |
| + | This can be the WPS, Reset, or other button on the device. | ||
| - | * first a moderate 0.1 second blinking rhythm during those two seconds, when router waits for user to trigger | + | The LEDs provide clues for timing |
| - | * then either | + | Watch the LED blinking speeds immediately after powering up the router. |
| - | * a slow 0.2 second blink continuing to the end of boot, if the failsafe was not triggered and the normal | + | Most routers show three different (power) LED blinking speeds during |
| - | * a rapid 0.05 second blink if the user pressed a button and failsafe mode was triggered | + | |
| - | **To enter failsafe mode, follow one of the procedures listed below:** | + | |
| + | | ||
| + | * Then either: | ||
| + | * A faster, 10-per-second blink if failsafe mode was triggered. The device is listening on 192.168.1.1 | ||
| + | * A slower, 2.5-per-second blink continuing to the end of normal boot, if the failsafe was not triggered | ||
| + | * If you missed the timing and see the slower blink rate, just power off the device, wait a couple seconds, and try again. | ||
| + | |||
| + | **Alternate for expert users: Wait (with a packet sniffer) for a special broadcast packet and press a button.** The packet will be sent to destination address 192.168.1.255 port UDP 4919. | ||
| + | The packet contains the text "// | ||
| + | So for example, in a terminal and using tcpdump, with the router connected to port eth0 of your computer, you would enter the command < | ||
| - | | + | **Alternate |
| - | * **Wait (with a packet sniffer) for a special broadcast packet and press a button.** The packet will be sent to destination address 192.168.1.255 port UDP 4919. The packet cnotains the text " | + | The message shown in the console is "//Press the [f] key and hit [Enter] to enter failsafe mode//" |
| - | * **Watch for a boot message on the serial console and press a key (" | + | |
| - | Usually, it is easiest to watch the LEDs. However, do consult the available documentation for your device, as there is no default button assigned as a reset button and not all procedures work on every device. Whichever trigger you use, the device will enter failsafe mode and you can access the command line with SSH (always possible) or a serial keyboard. | + | Usually, it is easiest to watch the LEDs. |
| + | However, do consult the available documentation for your device, as there is no default button assigned as a reset button and not all procedures work on every device. | ||
| + | Whichever trigger you use, the device will enter failsafe mode and you can access the command line with SSH (always possible) or a serial keyboard. | ||
| - | Note that LEDE uses always SSH, but early OpenWrt releases (15.05 and before) offered a telnet connection in this state but no SSH. | + | Note that modern OpenWrt always |
| + | |||
| + | |||
| + | ================= | ||
| - | Note: old Openwrt wiki page offer more details, most of them still valid: https:// | ||
| ==== Fixing your settings ==== | ==== Fixing your settings ==== | ||
| + | Once failsafe mode is triggered, the router will boot with a network address of 192.168.1.1/ | ||
| + | When in failsafe mode, the DHCP server will not be running. | ||
| + | You must set your computer' | ||
| - | Once failsafe mode is triggered, the router will boot with a network address of 192.168.1.1/ | + | Using SSH or a serial connection, you can then mount the JFFS2 partition with the following command: |
| - | < | + | < |
| mount_root | mount_root | ||
| </ | </ | ||
| - | After that, you can start looking around and fix what’s broken. The JFFS2 partition will be mounted to ///overlay//, as under normal operation. | + | After that, you can start looking around and fix what’s broken. |
| + | The JFFS2 partition will be mounted to '' | ||
| - | ==== Soft Factory Reset ==== | + | You can also transfer files by using scp command/protocol from Linux or macOS, or by using [[docs: |
| - | If you want a clean slate, there’s no need to flash again; just enter the following | + | |
| - | < | + | Additional steps required for [[: |
| - | umount | + | |
| + | < | ||
| + | # unplug external device | ||
| + | reboot | ||
| + | |||
| + | # plug external device | ||
| + | # mount external device, e.g. | ||
| + | block info | ||
| + | mount / | ||
| + | |||
| + | # fix the issue, e.g. | ||
| + | vi / | ||
| + | |||
| + | # verify external device will be mounted automatically, | ||
| + | vi /overlay/ | ||
| + | reboot | ||
| </ | </ | ||
| - | Note: for most routers, " | ||
| - | ==== Hard Factory Reset ==== | ||
| - | This command will erase and reformat the whole jffs2 partition and create it again: | ||
| - | < | + | Tipp: If you are not able to use '' |
| + | In this case use '' | ||
| + | |||
| + | |||
| + | ===== Factory reset ===== | ||
| + | A factory reset returns your router to the configuration it had just after flashing. | ||
| + | This works on any install with a squashfs / overlayfs setup (the norm for most installations), | ||
| + | |||
| + | With a large NOR chip, it can take 3 to 5 minutes for the overlayfs to be formatted in the flash. | ||
| + | During this time, changes cannot be saved. | ||
| + | |||
| + | **Caveat: | ||
| + | * Factory reset depends on completing the boot process. If factory reset is not working, try with failsafe mode instead. | ||
| + | * x86 builds (made for PC/Server hardware) with an ext4 read-write rootfs cannot be reset this way. | ||
| + | |||
| + | ==== Reset button ==== | ||
| + | On devices with a physical reset button, OpenWrt can be reset to default settings without serial or SSH access. | ||
| + | |||
| + | - Power on the device and wait for the status led to stop flashing (or go into failsafe mode, as described above). | ||
| + | - Press and hold the reset button for 10 seconds. | ||
| + | - Release the reset button. | ||
| + | |||
| + | The device will do a hard factory reset (see below) and then reboot. | ||
| + | This operation can be slow on some devices, so wait a few minutes before connecting again. | ||
| + | |||
| + | ==== Soft factory reset ==== | ||
| + | If you want a clean slate, there’s no need to flash again; just enter the following commands. | ||
| + | Your device' | ||
| + | |||
| + | Issuing " | ||
| + | Note that this "soft reset" is performed with file system actions, so in some cases it is not enough. | ||
| + | |||
| + | < | ||
| + | firstboot && reboot | ||
| + | </ | ||
| + | |||
| + | Note: If the commands above (all on one line) don't work, try those commands on separate lines in the terminal. | ||
| + | |||
| + | Note: for most routers, " | ||
| + | |||
| + | Note: if you're issuing this command inside a bash script, remember to add the option -y to force firstboot: | ||
| + | |||
| + | <code bash> | ||
| + | firstboot -y && reboot | ||
| + | </ | ||
| + | |||
| + | Here is a log of soft factory reset process in action, obtained via serial connection, during router startup**: | ||
| + | * < | ||
| + | Press the [f] key and hit [enter] to enter failsafe mode | ||
| + | Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level | ||
| + | f | ||
| + | - failsafe - | ||
| + | / | ||
| + | / | ||
| + | / | ||
| + | |||
| + | BusyBox v1.25.1 () built-in shell (ash) | ||
| + | |||
| + | ash: can't access tty; job control turned off | ||
| + | | ||
| + | / /\ _ ___ ___ ___ | ||
| + | / | ||
| + | / DE / \ | |__| _|| |) | _| | ||
| + | / | ||
| + | | ||
| + | \ LE \ / ----------------------------------------------------------- | ||
| + | | ||
| + | \________\/ | ||
| + | |||
| + | ================= FAILSAFE MODE active ================ | ||
| + | special commands: | ||
| + | * firstboot | ||
| + | * mount_root mount root-partition with config files | ||
| + | |||
| + | after mount_root: | ||
| + | * passwd change root's password | ||
| + | * / | ||
| + | |||
| + | for more help see: | ||
| + | http:// | ||
| + | ======================================================= | ||
| + | |||
| + | admin@(none):/# | ||
| + | [ 102.942293] jffs2reset: This will erase all settings and remove any installed packages. Are you sure? [N/y] | ||
| + | y | ||
| + | [ 117.606813] jffs2reset: / | ||
| + | [ 117.612055] jffs2reset: / | ||
| + | reboot | ||
| + | admin@(none):/# | ||
| + | ...</ | ||
| + | |||
| + | Tips**:** after (a OpenWrt based) router reboots or starts, it goes thru the bootmenu (selection menu for boot options) within 1 to 2 seconds (or, within 1 second, after preset delay time has passed). | ||
| + | The boot menu accepts Up/Down & Enter buttons, so avoid those or any other buttons for that period of time. | ||
| + | After that bootmenu stage, within 3 to 8 seconds later (depending on CPU speed, etc) the failsafe mode appears & passes, so you have to press the " | ||
| + | |||
| + | ==== Hard factory reset ==== | ||
| + | === Re-flashing the firmware === | ||
| + | Re-flash or upgrade the firmware discarding the settings. | ||
| + | |||
| + | <code bash> | ||
| + | sysupgrade -n / | ||
| + | </ | ||
| + | |||
| + | OpenWrt preserves settings [[docs: | ||
| + | |||
| + | === JFFS2 reset === | ||
| + | Reset the JFFS2 partition. | ||
| + | |||
| + | <code bash> | ||
| umount /overlay && jffs2reset && reboot | umount /overlay && jffs2reset && reboot | ||
| </ | </ | ||
| - | While essentially doing the same thing as // | + | Based on the mount status |
| + | |||
| + | === F2FS reset === | ||
| + | Reset the F2FS partition. | ||
| + | |||
| + | <code bash> | ||
| + | dd if=/ | ||
| + | </ | ||