NETGEAR R7200 v1

[ 0.000000] Linux version 5.10.138 (builder@buildhost) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r19685-512e76967f) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Sat Sep 3 02:55:34 2022 [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) [ 0.000000] MIPS: machine is Netgear R7200 [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] VPE topology {2,2} total 4 [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] On node 0 totalpages: 65536 [ 0.000000] Normal zone: 576 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 65536 pages, LIFO batch:15 [ 0.000000] percpu: Embedded 15 pages/cpu s30256 r8192 d22992 u61440 [ 0.000000] pcpu-alloc: s30256 r8192 d22992 u61440 alloc=15*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Writing ErrCtl register=000600d0 [ 0.000000] Readback ErrCtl register=000600d0 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 249356K/262144K available (7001K kernel code, 628K rwdata, 824K rodata, 1260K init, 243K bss, 12788K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 256 [ 0.000000] CPU Clock: 880MHz [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns [ 0.000012] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns [ 0.015861] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns [ 0.033802] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688) [ 0.106113] pid_max: default: 32768 minimum: 301 [ 0.115427] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.129829] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.147991] rcu: Hierarchical SRCU implementation. [ 0.157780] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build [ 0.173331] smp: Bringing up secondary CPUs ... [ 0.183040] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.183050] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.183061] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.183135] CPU1 revision is: 0001992f (MIPS 1004Kc) [ 0.243144] Synchronize counters for CPU 1: done. [ 0.304815] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.304825] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.304833] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.304878] CPU2 revision is: 0001992f (MIPS 1004Kc) [ 0.363990] Synchronize counters for CPU 2: done. [ 0.424321] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.424330] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.424338] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.424388] CPU3 revision is: 0001992f (MIPS 1004Kc) [ 0.483566] Synchronize counters for CPU 3: done. [ 0.543175] smp: Brought up 1 node, 4 CPUs [ 0.555589] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.575096] futex hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.588906] pinctrl core: initialized pinctrl subsystem [ 0.601602] NET: Registered protocol family 16 [ 0.611485] thermal_sys: Registered thermal governor 'step_wise' [ 0.613137] cpuidle: using governor teo [ 0.645447] FPU Affinity set after 11720 emulations [ 0.671784] clocksource: Switched to clocksource GIC [ 0.683738] NET: Registered protocol family 2 [ 0.692780] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.708716] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.725358] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.740497] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.754658] TCP: Hash tables configured (established 2048 bind 2048) [ 0.767400] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.780284] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.794401] NET: Registered protocol family 1 [ 0.802962] PCI: CLS 0 bytes, default 32 [ 0.813211] workingset: timestamp_bits=14 max_order=16 bucket_order=2 [ 0.830029] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.841522] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.861814] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 0.878162] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.889542] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.900870] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.912804] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.929699] printk: console [ttyS0] disabled [ 0.938174] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A [ 0.956097] printk: console [ttyS0] enabled [ 0.972631] printk: bootconsole [early0] disabled [ 0.994092] mt7621-nand 1e003000.nand: Using programmed access timing: 31c07388 [ 1.008945] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1 [ 1.021595] nand: Macronix MX30LF1G18AC [ 1.029242] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.044327] mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits [ 1.057370] mt7621-nand 1e003000.nand: Using programmed access timing: 21005134 [ 1.071928] mt7621-nand 1e003000.nand: Using programmed access timing: 21005134 [ 1.086505] Scanning device for bad blocks [ 2.383207] 7 fixed-partitions partitions found on MTD device mt7621-nand [ 2.396722] Creating 7 MTD partitions on "mt7621-nand": [ 2.407140] 0x000000000000-0x000000100000 : "u-boot" [ 2.418060] 0x000000100000-0x000000200000 : "SC PART_MAP" [ 2.430049] 0x000000200000-0x000000600000 : "kernel" [ 2.440941] 0x000000600000-0x000002e00000 : "ubi" [ 2.451459] 0x000002e00000-0x000004600000 : "reserved0" [ 2.462940] 0x000004600000-0x000004800000 : "factory" [ 2.474041] 0x000004800000-0x000008000000 : "reserved1" [ 2.533524] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 2.549625] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21 [ 2.567202] i2c /dev entries driver [ 2.832279] i2c-mt7621 1e000900.i2c: clock 100 kHz [ 2.844211] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges: [ 2.857611] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff] [ 2.875138] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000 [ 2.891443] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000 [ 2.907836] mt7621-pci 1e140000.pcie: Parsing DT failed [ 2.920675] NET: Registered protocol family 10 [ 2.931158] Segment Routing with IPv6 [ 2.938669] NET: Registered protocol family 17 [ 2.947628] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 2.973784] 8021q: 802.1Q VLAN Support v1.8 [ 2.985458] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 3.015374] mt7530 mdio-bus:1f lan4 (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7530 PHY] (irq=26) [ 3.037400] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7530 PHY] (irq=27) [ 3.059403] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7530 PHY] (irq=28) [ 3.081373] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7530 PHY] (irq=29) [ 3.103500] mt7530 mdio-bus:1f wan (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7530 PHY] (irq=30) [ 3.125596] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode [ 3.142415] DSA: tree 0 setup [ 3.148613] rt2880-pinmux pinctrl: pcie is already enabled [ 3.159689] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges: [ 3.173071] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff] [ 3.190592] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000 [ 3.206890] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000 [ 3.223288] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1) [ 3.238386] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0) [ 3.253372] mt7621-pci 1e140000.pcie: failed to parse bus ranges property: -22 [ 3.368006] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz [ 3.379124] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz [ 3.490427] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK) [ 3.504299] mt7621-pci 1e140000.pcie: PCIE0 enabled [ 3.514020] mt7621-pci 1e140000.pcie: PCIE1 enabled [ 3.523743] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002 [ 3.542432] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00 [ 3.555108] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff] [ 3.568801] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] [ 3.582508] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.593442] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] (bus address [0x00000000-0x0fffffff]) [ 3.613758] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400 [ 3.625736] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 3.638230] pci 0000:00:00.0: reg 0x14: [mem 0x60400000-0x6040ffff] [ 3.650779] pci 0000:00:00.0: supports D1 [ 3.658767] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 3.670775] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400 [ 3.682788] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 3.695281] pci 0000:00:01.0: reg 0x14: [mem 0x60410000-0x6041ffff] [ 3.707829] pci 0000:00:01.0: supports D1 [ 3.715819] pci 0000:00:01.0: PME# supported from D0 D1 D3hot [ 3.729028] pci 0000:01:00.0: [14c3:7615] type 00 class 0x000280 [ 3.741055] pci 0000:01:00.0: reg 0x10: initial BAR value 0x00000000 invalid [ 3.755115] pci 0000:01:00.0: reg 0x10: [mem size 0x00100000 64bit] [ 3.767768] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link) [ 3.798893] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 3.809324] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] [ 3.821466] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 3.835003] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref] [ 3.849389] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 3.862802] pci 0000:02:00.0: [14c3:7615] type 00 class 0x000280 [ 3.874821] pci 0000:02:00.0: reg 0x10: initial BAR value 0x00000000 invalid [ 3.888862] pci 0000:02:00.0: reg 0x10: [mem size 0x00100000 64bit] [ 3.901522] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link) [ 3.932692] pci 0000:00:01.0: PCI bridge to [bus 02-ff] [ 3.943121] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff] [ 3.955271] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff] [ 3.968788] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff pref] [ 3.983179] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 3.996419] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 4.009589] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 4.023467] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000] [ 4.036641] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000] [ 4.050506] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] [ 4.064032] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref] [ 4.078420] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff] [ 4.091959] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref] [ 4.106342] pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff] [ 4.119875] pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff] [ 4.133406] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff] [ 4.146923] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff] [ 4.160466] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit] [ 4.175039] pci 0000:00:00.0: PCI bridge to [bus 01] [ 4.184925] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff] [ 4.198448] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 4.211982] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref] [ 4.226378] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff 64bit] [ 4.240952] pci 0000:00:01.0: PCI bridge to [bus 02] [ 4.250839] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff] [ 4.264362] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff] [ 4.277893] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff pref] [ 4.294524] UBI: auto-attach mtd3 [ 4.301142] ubi0: attaching mtd3 [ 4.307988] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx [ 4.714766] ubi0: scanning is finished [ 4.738607] ubi0: attached mtd3 (name "ubi", size 40 MiB) [ 4.749436] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 4.763145] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 4.776669] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 4.790535] ubi0: good PEBs: 320, bad PEBs: 0, corrupted PEBs: 0 [ 4.802503] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 4.816892] ubi0: max/mean erase counter: 4/2, WL threshold: 4096, image sequence number: 1635066095 [ 4.835087] ubi0: available PEBs: 0, total reserved PEBs: 320, PEBs reserved for bad PEB handling: 20 [ 4.853474] ubi0: background thread "ubi_bgt0d" started, PID 457 [ 4.855798] block ubiblock0_0: created from ubi0:0(rootfs) [ 4.876422] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 4.898726] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 4.917179] Freeing unused kernel memory: 1260K [ 4.926258] This architecture does not have kernel memory protection. [ 4.939100] Run /sbin/init as init process [ 4.947260] with arguments: [ 4.947267] /sbin/init [ 4.947272] with environment: [ 4.947277] HOME=/ [ 4.947282] TERM=linux [ 5.496673] init: Console is alive [ 5.503922] init: - watchdog - [ 6.201085] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 11.093104] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 11.122186] init: - preinit - [ 12.046590] random: jshn: uninitialized urandom read (4 bytes read) [ 12.132314] random: jshn: uninitialized urandom read (4 bytes read) [ 12.200662] random: jshn: uninitialized urandom read (4 bytes read) [ 12.563975] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 12.580103] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 12.582294] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode [ 12.610458] 8021q: adding VLAN 0 to HW filter on device lan1 [ 12.624800] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 16.145917] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx [ 16.160906] IPv6: ADDRCONF(NETDEV_CHANGE): lan1: link becomes ready [ 17.170317] UBIFS (ubi0:1): Mounting in unauthenticated mode [ 17.182041] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 582 [ 17.265132] UBIFS (ubi0:1): recovery needed [ 17.450757] UBIFS (ubi0:1): recovery completed [ 17.459748] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 17.475345] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 17.495106] UBIFS (ubi0:1): FS size: 32251904 bytes (30 MiB, 254 LEBs), journal size 1650688 bytes (1 MiB, 13 LEBs) [ 17.515920] UBIFS (ubi0:1): reserved for root: 1523336 bytes (1487 KiB) [ 17.529103] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID BB2F90AC-15AA-42DA-84B2-1582B28B78F5, small LPT model [ 17.559187] mount_root: switching to ubifs overlay [ 17.588493] urandom-seed: Seeding with /etc/urandom.seed [ 17.776081] mt7530 mdio-bus:1f lan1: Link is Down [ 17.795992] procd: - early - [ 17.802117] procd: - watchdog - [ 18.451929] procd: - watchdog - [ 18.461445] procd: - ubus - [ 18.534410] random: ubusd: uninitialized urandom read (4 bytes read) [ 18.549457] random: ubusd: uninitialized urandom read (4 bytes read) [ 18.567054] random: ubusd: uninitialized urandom read (4 bytes read) [ 18.588306] procd: - init - [ 19.364232] kmodloader: loading kernel modules from /etc/modules.d/* [ 19.583463] urngd: v1.0.2 started. [ 19.671967] Loading modules backported from Linux version v5.15.58-0-g7d8048d4e064 [ 19.687086] Backport generated by backports.git v5.15.58-1-0-g42a95ce7 [ 19.793254] random: crng init done [ 19.800052] random: 30 urandom warning(s) missed due to ratelimiting [ 19.892289] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=22 [ 19.903097] pci 0000:00:00.0: enabling device (0006 -> 0007) [ 19.914379] mt7615e 0000:01:00.0: enabling device (0000 -> 0002) [ 19.939240] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 19.943771] mt7621-pci 1e140000.pcie: bus=2 slot=1 irq=23 [ 19.954710] pci 0000:00:01.0: enabling device (0006 -> 0007) [ 19.966111] mt7615e 0000:02:00.0: enabling device (0000 -> 0002) [ 20.041565] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht' [ 20.041610] ieee80211 phy1: copying sband (band 1) due to VHT EXT NSS BW flag [ 20.064718] mt7615e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a [ 20.064718] [ 20.064774] mt7615e 0000:02:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a [ 20.064774] [ 20.129479] kmodloader: done loading kernel modules from /etc/modules.d/* [ 20.390454] mt7615e 0000:01:00.0: N9 Firmware Version: _reserved_, Build Time: 20200814163649 [ 20.390507] mt7615e 0000:02:00.0: N9 Firmware Version: _reserved_, Build Time: 20200814163649 [ 20.529824] mt7615e 0000:01:00.0: CR4 Firmware Version: _reserved_, Build Time: 20190121161307 [ 20.529938] mt7615e 0000:02:00.0: CR4 Firmware Version: _reserved_, Build Time: 20190121161307 [ 25.516672] mtk_soc_eth 1e100000.ethernet eth0: Link is Down [ 25.537308] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 25.553275] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 25.565061] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode [ 25.583784] 8021q: adding VLAN 0 to HW filter on device lan1 [ 25.598763] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 25.612202] br-lan: port 1(lan1) entered blocking state [ 25.622672] br-lan: port 1(lan1) entered disabled state [ 25.634416] device lan1 entered promiscuous mode [ 25.644047] device eth0 entered promiscuous mode [ 25.670499] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode [ 25.684236] 8021q: adding VLAN 0 to HW filter on device lan2 [ 25.699097] br-lan: port 2(lan2) entered blocking state [ 25.710014] br-lan: port 2(lan2) entered disabled state [ 25.721653] device lan2 entered promiscuous mode [ 25.742195] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode [ 25.756066] 8021q: adding VLAN 0 to HW filter on device lan3 [ 25.772124] br-lan: port 3(lan3) entered blocking state [ 25.782645] br-lan: port 3(lan3) entered disabled state [ 25.794483] device lan3 entered promiscuous mode [ 25.815315] mt7530 mdio-bus:1f lan4: configuring for phy/gmii link mode [ 25.828988] 8021q: adding VLAN 0 to HW filter on device lan4 [ 25.843598] br-lan: port 4(lan4) entered blocking state [ 25.854072] br-lan: port 4(lan4) entered disabled state [ 25.865907] device lan4 entered promiscuous mode [ 25.889926] mt7530 mdio-bus:1f wan: configuring for phy/gmii link mode [ 25.903566] 8021q: adding VLAN 0 to HW filter on device wan [ 28.449399] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx [ 29.475754] br-lan: port 5(wlan1) entered blocking state [ 29.486431] br-lan: port 5(wlan1) entered disabled state [ 29.497749] device wlan1 entered promiscuous mode [ 29.507824] br-lan: port 5(wlan1) entered blocking state [ 29.518697] br-lan: port 5(wlan1) entered forwarding state [ 29.531487] br-lan: port 1(lan1) entered blocking state [ 29.542053] br-lan: port 1(lan1) entered forwarding state [ 29.554549] br-lan: port 5(wlan1) entered disabled state [ 29.566157] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 30.760386] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready [ 30.773369] br-lan: port 5(wlan1) entered blocking state [ 30.783998] br-lan: port 5(wlan1) entered forwarding state [ 32.263824] br-lan: port 6(wlan0) entered blocking state [ 32.274490] br-lan: port 6(wlan0) entered disabled state [ 32.285826] device wlan0 entered promiscuous mode [ 32.295695] br-lan: port 6(wlan0) entered blocking state [ 32.306551] br-lan: port 6(wlan0) entered forwarding state [ 32.318292] br-lan: port 6(wlan0) entered disabled state [ 32.967233] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 32.980343] br-lan: port 6(wlan0) entered blocking state [ 32.991081] br-lan: port 6(wlan0) entered forwarding state